Service manual

7020
Download EPROMs link and then select EPROMS for Accessories.
4. This change does not apply to the 7035.
FK101, how to allocate additional memory for the fax option.DESCRIPTION: SOLUTION ID:
86555
SOLUTION:
To change the memory amount available for scanning fax documents, perform the following:
1. Access the Key Operator Mode (press HELP, then touch Key Ope mode at the left front of touch
screen and then enter Password if necessary).
2. Touch 2. FAX from the Key Operator Mode screen.
3. Touch Special set from the Fax initial setting menu screen.
4. Enter password 9272 and touch OK.
5. Touch FAX file format on the Service mode setting screen.
6. Touch the UP or DOWN arrows to allocate desired fax file size (2MB or 4MB).
7. Touch Format in the lower left of touch screen, then YES to register the fax memory allocation
amount. (at this time any previously scanned files for sending or for printing are erased).
8. Touch BACK to return to the basic screen.
Note: When equipped with the standard 32MB, the memory amount can be changed from 2MB to
4MB, if more memory is added as 64MB go to Address Parameter list and change the data at
0B0003 to 011 for 8MB.
USAGE:
16
How to copy/print onto envelopes, 7020.DESCRIPTION: SOLUTION ID:
88666
SOLUTION:
Envelopes are not included in the paper specifications of this machine. Konica Minolta does not
recommend copying/printing onto envelopes with a 7020. The following special paper is
recommended:
Transparency film
Labels
Hole punch
Rag content
Note: These special papers must only be fed from the multi-sheet bypass tray.
USAGE:
16
FK101, how to program the default input tray for receive faxes.DESCRIPTION: SOLUTION ID:
89684
SOLUTION:
To program the receive fax input tray, perform the following:
1. Press Help key.
2. Press Key-Ope Mode button from the touchscreen.
3. Press [2: Fax] button.
4. Press Tx/Rx Mode set button.
5. Press Up Arrow (right hand side of the touchscreen) button twice.
6. Press Edit button until particular tray or [AUTOMATIC] is selected.
7. Press Back button twice
8. Press Return button.
Note: ATS must be turned on.
USAGE:
16
FK101, how to enable/disable the transmission confirmation report (TCR).DESCRIPTION: SOLUTION ID:
91908
SOLUTION:
SOLUTION: To enable/disable the TCR, perform the following:
1. Power the copier ON.
2. Press the [HELP] key.
3. Touch [Key-Ope mode] on the touchscreen.
4. Touch [2. FAX] on the touchscreen.
5. Touch [Report output set] on the touchscreen.
6. Touch the down-arrow located on the right side of the touchscreen one (1) time. [Transmission
report] should be highlighted.
7. Repeatedly touch [EDIT] located on the bottom of the touchscreen until the desired setting
appears. The available settings are:
OFF
Always
Only error
8. Touch [BACK] located on the lower right of the touchscreen two (2) times.
9. Touch [RETURN] located on the lower right of the touchscreen, which will return the machine to
the ready state.
USAGE:
16
F41-1 at power up.DESCRIPTION: SOLUTION ID:
120304
SOLUTION:
CAUSE: A loss of 24V DC at CN63-1 of the scanner driver board due to an open ICP1.
SOLUTION: Verify the operation of L1 (exposure lamp). To verify the operation of L1, perform the
following:
1. Access the 47 mode (power the copier ON, while simultaneously holding the 4 and 7 keys),
output code 00.
USAGE:
16
16
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005