Service manual

7020
Intermittent F51-06 code.DESCRIPTION: SOLUTION ID:
177885
SOLUTION:
CAUSE: Failed write unit.
SOLUTION: Replace write unit (p/n 26NA-6503).
Note: Before replacing the write unit, ensure 24V DC for the polygon motor is present at CN22 pin
5 of the PRDB.
USAGE:
0
DF314, "Reload original in order, then set scanning conditions of originals" message
displayed when copying odd size original through the document feeder.
DESCRIPTION: SOLUTION ID:
179893
SOLUTION:
CAUSE: Non-standard size was not selected.
SOLUTION: When feeding Non-standard size paper through the DF314, the [Non- standard size]
needs to be selected in the [ORIGINAL MODE]. To select [Non-standard size] Perform the
following:
1. On the display panel select [ORIGINAL MODE].
2. On the display panel select [Non-standard size].
3. Place the original in the DF314 feed tray and press [START].
Note: This application can also be programmed into job number 15, to have the machine powered
ON with this function.
USAGE:
0
Is Unimessage Pro available for the FK102?DESCRIPTION: SOLUTION ID:
180104
SOLUTION:
Unimessage Pro utility is not a function used with the FK102.
USAGE:
0
Is Unimessage Pro available for the FK101?DESCRIPTION: SOLUTION ID:
180108
SOLUTION:
Unimessage Pro utility is not a function used with the FK101.
USAGE:
0
FK101, When 'Reduction for record' is set to 100% in Key Operator Mode 'Tx/Rx mode set', it
is printed as 96% on the FAX setting list. This failure occurs only on the FAX setting list.
DESCRIPTION: SOLUTION ID:
181663
SOLUTION:
CAUSE: Initially the maximum reception zoom was only 96%. After a certain period, life size
reception (100%) was added. At this time, the corresponding change was not made in the FAX
setting list.
SOLUTION: The failure is included in the system control program and will be corrected on the next
upgrade of each program.
USAGE:
0
FK101, when TEL/FAX auto switch is ON and pseudo Ring of TEL reception is calling, if
external handset is off-hook, "Reception Error" is displayed on control panel screen for a
few seconds. In addition, this failure is only displayed. There is no problem with
communication and/or journal record.
DESCRIPTION: SOLUTION ID:
181687
SOLUTION:
CAUSE: Message is displayed because of internal process related to the system control.
SOLUTION: Since this message does not have to be displayed, it will be corrected in the next
system control program upgrade.
USAGE:
0
FK102, Is there an audible beep when faxes are received?DESCRIPTION: SOLUTION ID:
181882
SOLUTION:
There is an audible beep when the Fax is first being received, but there is no audible beep after the
Fax has been printed.
USAGE:
0
FL102, how to set line 2 for RX only.DESCRIPTION: SOLUTION ID:
182240
SOLUTION:
To set line 2 for RX only, perform the following:
1. Access the [Key-ope mode].
2. Select [4. FAX].
3. Select [FL102 settings].
4. Select [Line parameter set].
5. Scroll to Line2 Com set, press [EDIT] and change the setting to RX only.
6. Power the copier OFF/ON.
USAGE:
0
Change of paper feed gear material in driving section and change of driving auxiliary panel.DESCRIPTION: SOLUTION ID:
182952
SOLUTION:
See [[M20030277A0| URL http://techweb.konicabt.com/tpm/media/mn20030277a0.pdf]] for details.
Note: To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded
for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html|
USAGE:
0
135
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005