Service manual

7020
*[[Trademark ownership information| FILE V:\TEXT\TRADEMRK.TXT NEW]]
Safety label regarding clearing fixing unit jam.DESCRIPTION: SOLUTION ID:
154736
SOLUTION:
To prevent injury when clearing a fusing unit paper jam, two safety labels (a caution and arrow
label) are available that warn the operator of the high temperature area of the fusing unit. The
caution label provides notice of the high temperature area and the arrow label identifies the area of
concern. Both labels must be applied as shown in [[Safety Bulletin #64a| URL
http://techweb.konicabt.com/tpm/media/sb64a.pdf]].
Notes:
1. [[Link for internal use only| RUN v:\PDFfiles\AcroRd32.exe v:\PDFfiles\internal_link008.pdf]]
2. To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded for
free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html| URL
http://www.adobe.com/products/acrobat/readstep2.html]]
*[[Trademark ownership information| FILE V:\TEXT\TRADEMRK.TXT NEW]]
USAGE:
0
How to use the password print (secure printing) function.DESCRIPTION: SOLUTION ID:
155315
SOLUTION:
To use password print, a hard drive is required in the IP, the ECM mode must be enabled, user
ECM account(s) must be created, software dip switch 26-4 must be turned ON, and the ECM User
ID and password must be entered in the print driver.
To turn ON software dip switch 26-4, perform the following:
1. Power the copier OFF.
2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys).
3. Select SOFTWARE SW.
4. Using the up/down arrows, scroll to software switch 26-4.
5. Select ON.
6. Power the copier OFF/ON.
To enable ECM mode for password printing, perform the following:
1. Press the Help to enter Key Operator mode.
2. Press the Key-Ope Mode button on the touch screen.
3. Enter the Key Operator password (if necessary) and press OK.
4. Press System/Copier.
5. Press ECM.
6. Enter the 8 digit ECM master code (the default passcode is 00000000).
7. Press ECM ON/OFF Setting.
8. Select the ON setting for (Copier, Fax, or Printer) as desired.
9. Press OK.
10. Make any additional changes to the ECM accounts as desired.
11. Power the machine OFF/ON.
To perform password printing (using the PCL, PostScript or Visual PostScript driver), perform the
following:
1. From the document to be printed, select file then print from the file menu.
2. Select properties in the print driver dialog box.
3. Check the password check box.
4. In the ID box of the Password Setting dialog box enter the ECM user account number.
5. Enter any numeric password up to 8 digits in the password box.
6. Select OK.
7. Make any additional desired changes to the print driver and select OK.
8. Select OK to print the document.
9. On the operation panel of the machine, press the Scan/Print button.
10. Press Password Print on the LCD touch screen.
11. Enter the ECM user account number in the User ID space using the numeric keys on the
touchscreen.
12. Press OK.
13. Enter the same numeric password that was entered in the print driver using the numeric keys
on the touchscreen.
14. Select the number of the job to be printed and press the print button.
Note: The print job will not be printed until the matching password is entered at the main body. The
password print feature will increment the ECM user account.
USAGE:
0
Black streaks.DESCRIPTION: SOLUTION ID:
156293
SOLUTION:
CAUSE: Dirty charge corona and grid
SOLUTION: Clean charge corona and grid
SPECIAL NOTE: Solution provided by Bob Schimmelpfenning, Modern Business Machines.
USAGE:
0
125
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005