Service manual

7020
highlighted.
5. Using the [EDIT] key, change the setting to (0).
6. Press the [BACK] key.
7. Select [Special Set].
8. Enter the passcode (9272).
9. Select [Function Parameter Setting].
10. Select [Network].
11. [RCV Signal Detect Mode] will be highlighted.
12. Using the [EDIT] key, change the setting to (Time).
13. Using the [DOWN ARROW] on the touch screen, scroll down until [RCV Signal Detect Time] is
highlighted.
14. Using the [EDIT] key, change the setting to (6 sec).
15. Power the machine OFF/ON.
PLEASE LOAD 8.5x11, NORMAL PAPER message when printing. 8.5x11 paper is loaded and
when selected, READY TO RESTART, PRESS FORMFEED TO FORCE PRINTING is
displayed.
DESCRIPTION: SOLUTION ID:
135101
SOLUTION:
CAUSE: ATS/APS is disabled in the Key Operator mode.
SOLUTION: To enable ATS/APS, perform the following:
1. Power the copier ON.
2. Press the [HELP] key.
3. Touch [Key-Ope mode] on the touchscreen.
4. Touch [1. System/copier] on the touchscreen.
5. Touch the down-arrow located on the lower left corner of the touchscreen.
6. Touch [12. Memory SW] on the touchscreen.
7. Touch the down-arrow located on the right side of the touchscreen five (5) times [Auto tray
switch] will be highlighted. Repeatedly, touch [EDIT] until [ON] is displayed as the setting selection.
8. Touch the down-arrow on the right side of the touchscreen three (3) times [ATS/APS (Bypass)]
will be highlighted. Repeatedly, touch [EDIT] until the setting selection displayed is [ON] (ATS/APS
enabled for the bypass), or [OFF] (ATS/APS disabled for the bypass) as desired by the customer.
9. Touch the down-arrow on the right side of the touchscreen [ATS/APS SW(Tray 1)] will be
highlighted. Repeatedly, touch [EDIT] until the setting selection displayed is [ON] (ATS/APS
enabled for Tray 1).
10. Touch the down-arrow on the right side of the touchscreen [ATS/APS SW(Tray 2)] will be
highlighted. Repeatedly, touch [EDIT] until the setting selection displayed is [ON] (ATS/APS
enabled for Tray 2).
11. Touch the down-arrow on the right side of the touchscreen [ATS/APS SW(Tray 3)] will be
highlighted. Repeatedly, touch [EDIT] until the setting selection displayed is [ON] (ATS/APS
enabled for Tray 3).
12. Touch the down-arrow on the right side of the touchscreen [ATS/APS SW(Tray 4)] will be
highlighted. Repeatedly, touch [EDIT] until the setting selection displayed is [ON] (ATS/APS
enabled for Tray 4).
13. Touch [RETURN] three (3) times to return to the normal copy mode.
SPECIAL NOTE: Solution provided by Wayne Winters, Caltronics Business Systems
USAGE:
0
'PLEASE INSERT KEY COUNTER' message is displayed when printing with a key counter
installed.
DESCRIPTION: SOLUTION ID:
135237
SOLUTION:
CAUSE: Software switch 17-3 (host printing cannot be performed when a key counter is installed)
is enabled.
SOLUTION: Disable software switch 17-3 (host printing cannot be performed when a key counter is
installed). To disable software switch 17-3 perform the following:
1. Power the copier OFF.
2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys).
3. Select [1. SOFTWARE SW].
4. Using the up/down arrows, scroll to software switch 17-3.
5. Select OFF.
6. Power the copier OFF/ON to return to normal copy mode.
USAGE:
0
'PRINTING IS PROHIBITED' message and the print job is aborted.DESCRIPTION: SOLUTION ID:
135252
SOLUTION:
CAUSE: Software switch 17-3 (host printing cannot be performed when a key counter is installed)
is enabled with no key counter installed.
SOLUTION: Disable software switch 17-3 (host printing cannot be performed when a key counter is
installed). To disable software switch 17-3 perform the following:
1. Power the copier OFF.
2. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys).
USAGE:
0
119
Copyright 2005, Konica Minolta Business Solutions U.S.A., Inc.
May 2005