Service manual

ManualsBrandsScan-Graphics ManualsPrint & ScanCF500/44

7020

cable that is connected to the master channel of the PC or IP controller. Power is supplied by the

IP/PC's power supply through a standard power connector.

3. Use a Microsoft Windows 98 boot disk which can be created on a Windows 98 workstation.

4. Connect the hard drive to the 40-pin connector on one side of the adapter and connect the

IP/PC's IDE cable to the 44-pin connector on the other side of the adapter. Ensure that [[Pin 1 on

the IDE connector and hard drive| IMAGE V:\BITMAPS\IP411_HD_connect.bmp SCROLL]] is

connected to [[Pin 1 on the adapter| IMAGE V:\BITMAPS\IP411_HD_connect1.bmp SCROLL]].

5. Insert the 98 Boot disk into the floppy drive of the IP/PC, reconnect the IP/PC power cord, and

power ON the IP/PC.

6. Once the IP/PC boots from the floppy, press return at the date and time prompts to get to the A:

prompt.

7. Use FDISK to create a primary DOS partition and set it as active.

WARNING: Do not use large disk support.

8. Format the newly-created partition with the /s switch to transfer system files.

=================================C A U T I O

N=================================

If the hard drive is not connected to the IDE master channel, and is not configured to be the

MASTER

drive, the setup program will format whatever drive is connected and setup as the MASTER

drive.

===========================================================================

9. Remove the hard drive from the PC and reinstall it the IP unit. Allow the IP and main body to

completely boot or this process will have to be repeated.

*[[Trademark ownership information| FILE V:\TEXT\TRADEMRK.TXT NEW]]

DF314, RADF FAILURE PLEASE CALL SERVICE message.DESCRIPTION: SOLUTION ID:

102090

SOLUTION:

PROBABLE CAUSES:

1. The ADF CB has failed.

Reseat the connectors on the ADF CB and loosen ties wraps on wiring harness to ensure proper

communication is taking place between the ADF and the main body. Reflash the files in the ADF.

If problem persists, replace ADF CB (p/n 13GL-9010).

2. Failure of the original reversal motor (M303). When checking the document feeder

photosensors, all operate properly in diagnostics.

To verify the operation of M303, perform the following:

a. Power the machine OFF.

b. Access the 47 multimode (power the machine ON while pressing the 4 and 7 keys), output

code 60, P-2-3 to verify the operation of M303.

c. If motor drive does not occur, it is necessary to replace M303 (p/n 13GL80030). It may also

be necessary to replace the RADF CB (p/n 13GL-9019) if the motor damaged the board.

Notes:

I. If the new ADF CB needs to be flashed, DF314 write protection must first be turned OFF.

To turn OFF DF314 write protection, perform the following:

A. Power the copier OFF.

B. Access the 25 mode (power the copier ON, while pressing the 2 and 5 keys).

C. Select [ 1. SOFTWARE SW].

D. Using the up/down arrows, scroll to software switch 23-6.

E. Select ON.

F. Power the copier OFF/ON to return to normal copy mode.

II. System control firmware level 32 CGDO (minimum level) must be installed for the

dipswitch to function.

III. Refer to the [[ADF serial number, DF Control Board, firmware version and model

compatibility matrix| URL http://techweb.konicabt.com/tpm/media/t20030054a1e.pdf]].

IV. To view the PDF, Acrobat* Reader must be installed. Acrobat Reader can be downloaded

for free from the Adobe* Web site at: [[http://www.adobe.com/products/acrobat/readstep2.html|

URL http://www.adobe.com/products/acrobat/readstep2.html]]

*[[Trademark ownership information| FILE V:\TEXT\TRADEMRK.TXT NEW]]

USAGE:

F26-1 at power up.DESCRIPTION: SOLUTION ID:

112220

SOLUTION:

PROBABLE CAUSES:

1. The TDS (Toner Density Sensor), in the developing unit, has detected a depletion of toner.

Note: This may have been caused by the customer making an excessive amount of copies while

the machine was out of toner. It may also be caused by a bound toner addition system.

Clean all toner from the toner recycle and toner supply assemblies. Confirm that the gear mesh

between the toner supply auger drive gear and toner supply motor (M4) is flush. If toner supply

conveyance is normal and the toner cavity is empty, install a new toner cartridge (Item #950236)

USAGE:

May 2005