User manual

03
22
27
grease
tread-lock
7 6
9 7
6
10
12
3 5 1 / 5 6 1
8 6 1 / 0 8 1
23
4
3
2 4
16
22
2
www. SCALEDRIVE .de
ScaleART OHG / Schillerstraße 3-7 / D 67165 Waldsee
Tel.: [phone] / Mail: [e-mail]
Item nr.: 74000401 - front-axle differential
Compatible with all common commercial vehicle construction-
kit in scales: 1:13 - 1:16
- fibre-glass reinforced plastic
- milled steel und bronze gear
- all shafts and screws are made of stainless steel
- 10 ball bearings
- transmission 2,67 : 1 (identically with Tamiya)
- maximum steering angle 42°
- many variable mounting options
This model is not a toy. Furthermore is it not qualified for the use of children under the age of 14.
Technical changes and modifications are reserved. We do not take any responsibility for misprints
or misunderstanding of the construction-detail. Reproducing and multiplying our construction -
plans without our permission will be prosecuted.
set of front-axle parts 4 23000289
axle housing 2 23000250
cover without counters. 1 23000254
diff cover 1 23000255
crown wheel 1 23000260
pinion hafl-shaft 2 23000263
pinion cage 2 23000272
drive pinion 1 23000261
differential cage 1 23000267
half-axle front-axle 2 23000284
CVD joint 2 23000285
wheel center bolt 2 23000275
socket joint CVD 2 23000276
threaded bushing M2 4 15000022
needle bearing d5mm 2 32900030
ball bearing d5 x 11 x 4 2 32900005
ball bearing d5 x 9 x 3 2 32900036
ball bearing d7 x 11 x 3 4 32900035
counters. screw M1,6x6 5 32000069
counters. screw M2x6 5 32000072
screw M2x5 5 32000011
screw M2x6 35 32000012
screw M2x20 18 32000019
allen screw M3x6 3 32000592
screw M3x16 3 32000057
worm screw M2x3 3 32000230
worm screw M2,5x5 2 32000238
nut M2 55 32000002
self locking nut M3 3 32000913
circlip d3,2mm 2 32000721
circlip d4mm 3 32000722
washer d3,2 3 32000222
washer d5 x 0,2mm 2 32000210
washer d5 x 0,5mm 3 32000211
pin d1,5x8 3 32000376
pin d2x10 5 32000383
pin d3x18 1 32000477
steering lever M3x75 1 37030018
steering lever M3x85 1 37030019
tube 3x0,5x17,5 4 36035011
plain bearing 3x4,5x5 4 32900032
ball joint M3 2 32900414
grease 10g 2 60000507
allen key 0,9mm 1 60000303
allen key 1,3mm 1 60000304
A
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
A2
A1
A7 A4 A6 A3
A5
A8
36
34
26
08
05
20
06
34
04
05
20
D3,2mm
D4mm
M1,6x6
M2x5
M2,5x6
D3x18
tread-lock
D5 x 0,2
D5 x 0,5
09
30
15
29
16
02
16
07
32
33
Due to manufacturing tolerances there can be burrs on holes and surfaces.
Theses must be removed with a file or sandpaper to guarantee that the parts
are fitting each other.
2x
D2x10
D1,5x8
M2x3
18
14
25 10
11
35
12
2x
- 1 -
M2,5x5
The following tools are required for assembly:
Phillips screwdriver Art.Nr.: 96000007
socket wrench 4,0mm Art.Nr.: 96000016
socket wrench 5,5mm Art.Nr.: 96000018
allen key 2mm Art.Nr.: 96000010
nose pliers Art.Nr.: 96000051
diagonal cutter Art.Nr.: 96000052
scalpell Art.Nr.: 96000036
tread locking fluid medium str. Art.Nr.: 60000504
small file
tread-lock
M2x5
M2
M2x20
The washers 32 and 33 are used to compensate tolerances. If the drive
pinion 07 operates hard after the final assembly of the axle remove one or
two washers.
tread-lock
tread-lock
20
27
01
22
20
01
27
tread-lock