THIS MANUAL CONTAINS THE OPERATING INSTRUCTIONS AND SAFETY INFORMATION FOR YOUR SCAG ACCESSORY. READING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSORY PERFORMING TO MAXIMUM EFFICIENCY. THE SPECIFIC MODELS THAT THIS BOOK COVERS ARE CONTAINED ON THE INSIDE COVER. BEFORE OPERATING YOUR MACHINE, PLEASE READ ALL THE INFORMATION ENCLOSED.
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your mower.
A replacement manual is available from your authorized Scag Service Dealer or by contacting: Scag Power Equipment, Service Department at P.O. Box 152, Mayville, WI 53050. You may also contact us through our website at www.scag.com The manual for this grass catcher can be downloaded by using the model and serial number or use the contact form to make your request. Please indicate the complete model and serial number of your Scag product when requesting replacement manuals. 1.
5. To clean the hopper debris screen; 3. When dumping the hopper into a disposal area: WARNING DO NOT DUMP CLIPPINGS IN A DISPOSAL AREA THAT IS BURNING A. B. Disengage the deck drive, apply the parking brake and allow all moving parts to come to a complete stop. Pull downward on the hopper door handle to allow the hopper sweeper to remove the material from inside the hopper. See Figure 2-1. A. Disengage the deck drive and allow all moving parts to come to a complete stop. B.
3.1 ASSEMBLY INSTRUCTIONS FOR 48" AND 52" CUTTER DECK -NOTEWhen installing this grass catcher on a machine with a serial number range from 7630001 to 8479999, you will need to install part number 461764 for a 48" cutter deck or 461765 for a 52" cutter deck. This kit includes a new Turbo Baffle and Deck Baffle. -NOTEUse the illustrated parts list as a part number reference when following the assembly instructions. 1. Remove all packaging materials.
FLATWASHER ELASTIC STOP NUT CARRIAGE BOLT FIGURE 3-2 BLOWER ASSEMBLY HAIR PIN TIGHTEN CATCH PLATE HARDWARE MOUNTING PIN TIGHTEN MOUNTING BRACKET HARDWARE MOUNTING BRACKET P R O P E R Y L S E C R E V I E N G E I W T H I OL I A N D FUEL. RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.
10. Install the new belt covers and secure. See items number 1 and number 21 on page 10 of the Blower Mounting Components section in the Illustrated Parts List for proper installation. -NOTEThe hopper dump handle can be installed on either side for operator convenience. When installing this grass catcher on a machine with the Roll Over Protection System (ROPS), the curved handle will need to be installed on the right side. 11.
4.1 GRASS CATCHER REMOVAL INSTRUCTIONS 5. With help from an assistant, remove the hopper assembly from the mounting posts. 1. Prepare the work area making sure that it is a clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 4-1. WARNING DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING KIT, OR ENTIRE GRASS CATCHER INSTALLED 3.
Notes 7
GC-STC 48" & 52" BLOWER HOUSING ASSEMBLY 9 48 10 11 12 13 4 2 1 8 9 5 3 11 7 6 10 10 44 14 47 27 14 12 11 15 43 16 42 26 41 39 18 W FO E B R E E IN V HL O C UA C MAAN M LT 'S E GR B TINATO R LL RAOPE TA E D S PREA IN O 40 A R 34 15 14 17 N IN G 27 R 19 E 17 25 28 20 41 21 38 3 35 22 27 23 51 24 46 14 RO BLOWER ROTATING BLADES BEFORE ENGINE CHUTE ENTERING CAN T 24 DA NG ER Stop IN en G gine B DISC UN DO NO be LA DE LE HA SS T OP fore S cl RG GR E
GC-STC 48" & 52" BLOWER HOUSING ASSEMBLY Ref. No. Part Number Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 04067-07 481547 04019-02 04001-59 04001-01 423298 481428 482300 04024-02 04021-05 04041-07 43277 482299 04021-09 04030-04 423933 04003-05 04001-54 04001-46 04001-81 04001-21 461812 482278 482079 04043-04 43575 481039 Pin, Ring 2-1/4" Long Lanyard, Deck Height Pin Nut, Serr.
GC-STC 48" & 52" BLOWER MOUNTING COMPONENTS FOR MACHINES WITH A SERIAL NUMBER BETWEEN 7630001 - 8479999 ONLY 31 30 10 24 23 25 25 6 10 26 11 5 26 29 2 28 4 32 6 7 1 27 29 8 27 3 28 6 12 UNDER SIDE OF CUTTER DECK SHOWN 9 13 21 14 22 20 15 15 16 18 17 19 RIGHT SIDE OF CUTTER DECK SHOWN 390STC203B 10
GC-STC 48" & 52" BLOWER MOUNTING COMPONENTS Ref. No.
GC-STC-CS HOPPER COMPONENTS 16 14 49 50 45 45 5 4 3 41 15 31 43 11 51 17 56 55 40 58 59 8 12 9 6 49 53 2 25 50 B 55 34 42 24 27 43 49 53 18 61 48 38 63 49 34 53 49 50 52 41 54 12 18 53 49 58 59 28 7 1 33 49 69 38 49 45 49 49 25 36 21 58 53 20 59 19 53 64 66 33 65 29 61 71 71A 33 38 30 38 22 35 13 46 37 57 C 23 65 64 21 32 49 49 49 40 49 66 65 53 63 33 19 C A 62 10 34 36 49 60 61 37 60 20 70 24 33 10 49 6 29 34 68 32 2
GC-STC-CS HOPPER COMPONENTS Ref. No.
GC-STC-CS DECALS 481039 482275 481327 481377 483037 483039 14
LIMITED WARRANTY- COMMERCIAL ACCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within the warranty period.
© 2004 SCAG POWER EQUIPMENT DIVISION OF METALCRAFT OF MAYVILLE, INC www.scag.com PART NO.
