Technical Data Kandi Electric Vehicle User Operating Manual Kandi Technologies Group, Inc.
1 Preface Preface Thanks for your trust to choose Kandi Electric Vehicles with zero emission and zero pollution, a model possessing such performances as good safety, comfort and economy. we are now shouldering our enterprise mission to prolong the life of the earth, and looking forward to adding fun to your work and life with products and service of high quality. Please read this manual carefully prior to driving the car for the first time .
2 Table of Contents Contents Preface.............................................. 1 About this Manual .......................... 4 General ............................................. 5 Cab ................................................... 8 List ............................. 8 Instruments and Indicators ............ 9 Instrument ....................... 9 Driver Information System ......... 13 Centralized Control Screen System ... 16 ON and OFF .................................. 25 Mechanical Key ..
Table of Contents Charging Method ................. 75 Wheel ......................... 90 Technical Data ............................. 114 110V Charging Operation .......... 77 Anchor Aid ..................................... 97 Description of Data ...............114 Replace Wheels .................. 97 Car Technical Data ...............115 Towing a Car ................... 100 Maintenance ................................. 117 Fuse and Bulb .............................. 103 Vehicle Maintenance...
4 About this operating manual About this Manual This manual includes important information, tips, suggestions and warnings related to the use of this vehicle. Make sure to keep this Operating Manual in the car all the times. This is very important especially when you lend or resell the car to others. The Manual describes the contents of the vehicle equipment at the time of final draft.
General General Installation of accessories Please contact with a Kandi-authorized dealer prior to the installation of any accessories. Various kinds of accessories and optional accessories can be installed only within the scope of your region permitted by the laws and regulations, and must also meet the requirements of various inspections and the precautions described in various business documents related to the car.
General 6 Safe Driving Technology Although it is impossible to ensure you’re driving safe and prevent from an accidents 100%, we still recommend that you pay full attention to following matters in order to either prevent from an accidents or reduce losses when an accident occurs. Prior to driving, you and your passengers must fasten your seat belt respectively. When the ignition key is in the ignition system, do not get out of your car nor leave your child alone in the car.
Cab Some equipment listed herein is only used for either a specific model or an optional 7
Cab 8 Cab ⑾ Cigar lighter. List ⑿ Shift knob. ⒀ Parking brake lever. ⒁ Acceleration pedal. ⒂ Brake pedal. ⒃ Front hood opening handle. ⒄ Central door lock switch. ⒅ Power window Regulator. ⑴ ⑵ ⑶ ⑷ ⑸ ⑹ Air outlet with adjusting wheel. Lights switch. Instrument regulating switch. Steering wheel. Instrument cluster. Ignition switch. ⑺ Window glass wiping and cleaning device. ⑻ Emergency switch. ⑼ Central controller. ⑽ Glove box.
Instruments and Indicator Light Instruments and Indicators Instrument ⑥ Voltameter. ⑦ Tachometer. Instrument Cluster List Odometer The combination instrument is an information center for the driver to use. Recording total mileage driven by the car accumulatively. Odometer for Driving The drivable range odometer indicates drivable mileage which is predicted based on residual electric quantity and consumed electric quantity. Electricity Meter Electricity meter indicates approx.
10 Instruments and Indicator Light be the risk in either over-discharge of the battery or the vehicle at anchor. Wattmeter What shown on the power meter is the instant power passed through the power battery while the car is driving (cyan) and is charging or the energy is fed back (green). Speedometer The speedometer is used to indicate real-time speed of the vehicle during driving. Voltmeter The voltmeter is used to indicate current power battery voltage of the vehicle.
Instruments and Indicator Light Total mileage indicating range is 0-999999 mi, and it cannot be zeroed, and remains unchanged when the mileage is accumulated to the maximum value. Trip indicates total mileage driven after previous trip is reset, and its indicating range is 0-9999.9mi, and zeroed automatically after exceeding 9999.9mile. When the mode switchover button is switched to the trip, the trip can be reset to zero by pressing and holding the mode switchover button for more than 1 second.
12 Instruments and Indicator Light Indicator mark for the complete vehicle When the indicator is on or the buzzer works Treatment method of indicator or warning light on Indicator mark for the vehicle Brake System Fault Warning Light When the ignition switch is at “ON” position, this warning light is Instruction on in the following conditions.
Instruments and Indicator Light Warning ! It is very dangerous to continue driving when the brake liquid is too low. Send your car for inspection to service station authorized by Kandi under the following conditions: Power Battery Failure Warning Light Power battery failure warning light. If the light comes on during driving, it indicates that the power battery fails.
14 Instruments and Indicator Light High beam light indicator light Low beam light indicator light The indicator light will be on when the ignition system is in ON or STAR gear and the position light is on. Position light indicator light Front fog Light Indicator Light Front fog light indicator light This indicator light is on when the front fog lights are turned on.
Instruments and Indicator Light Rear Fog Light Indicator Light This indicator light is on when the rear fog lights are turned on. Seat-Belt Indicator Light When the driver does not fasten the seat belt in the absent of an passengers on the front passenger seat or any of passengers on the driver’s seat or the front passenger seat does not fasten the seat belt, the indicator light for seat belt will be lit and the instrument gives an alarm at the same time, reminding that the driver fastens the seat belt.
16 Instruments and Indicator Light According to the connection direction of the turn signal light, the left or right indicator light will flash accordingly. When the flashing alarm device is connected, two indicator lights will flash at the same time. If a turn signal light does not work, the flashing frequency of the indicator light is about twice as fast.
Instruments and Indicator Light Main interface (homepage) Bottom operation bar Status Bar ① ⑤ Return. click and return to the interface of previous level. ⑥ Home page: Click to return to the home page interface. ⑦ Volume: click and the window for volume adjustment pops up. WIFI(icon) When WIFI is connected, the icon is bright white. and if WIFI is not connected, the icon is gray. ② Bluetooth (icon) When Bluetooth is not opened, icon is displayed as dark gray.
Instruments and Indicator Light 18 Main Interface ⑴ System time: displays the system time and date. ⑵ Remaining mileage: the remaining mileage of the vehicle displays. ⑶ Music: via the local music player inlet, press the button to operate the control and from left to right is previous song, play / pause and next song. ⑷ Radio: via the radio FM play entrance, press the button to operate the control and from left to right are previous one, play / pause, next one from left to right.
Instruments and Indicator Light currently playing music) and song words (click the button to enter the window of displaying the song words of current playing music). Music interface ③ Play progress bar, you can drag the progress bar manually to control the play progress. and the play time can be shown in real time. ④ Display the songs in the current playlist, click the song in the list to play directly.
Instruments and Indicator Light 20 ① Display the frequency of the currently playing radio station. ② Through the radio frequency search range, the slide frequency set can be manually adjusted. ③ Play button control: from left to right are previous radio ( click the button to decrease the frequency by 0.05MHz), close ( click the button to close and exit the radio Application), next radio (click the button to increase the frequency by 0.
Instruments and Indicator Light Bluetooth music interface ③ Play progress bar, and display the play time point in real time. Applications Bluetooth music interface ① Display the name of music playing.
Instruments and Indicator Light 22 ② Browser: After the centralized control screen is connected to WIFI, you can enter the browser to browse the Internet. ③ File manager: after entering the file manager, you can copy, cut and paste, and cancel the local file. ③ ④ Air Conditioner Control the air volume of air conditioner by clicking button “-” and “+”.
Instruments and Indicator Light ② ③ ④ ⑤ ⑥ Display the dial number. Dial keypad. Address book button, click the button to view the phone address book. Make a call and answer/hang up the call. Call record query. ② Display the summary information of power battery, including total voltage, total current, maximum temperature, minimum temperature, maximum monomer voltage, minimum monomer voltage, insulation resistance and the number of batteries.
Instruments and Indicator Light 24 ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ Display: Adjust the display backlight brightness of the centralized control screen, and set the backlight brightness adjustment after turning on the small light of the vehicle. Bluetooth: Set Bluetooth name, PIN code, automatic connection switch and auto answer switch.
ON and OFF ON and OFF Mechanical Key Key Unit Every car is equipped with two mechanical keys. Regulator), which may cause a risk of accidents! The key cannot be pulled out of the ignition system before the car stops. Otherwise, the steering lock will be locked suddenly, which may cause a risk of accident! Central Door Lock Central Door Lock Switch The central door lock can be operated with the switch on the driver's door.
26 ON and OFF Instruction Or the control over the central door lock can be achieved through the toggle button on the interior handle on the driver's side. trunk lid. However, since a locked door will make it more difficult to rescue from outside in an emergency, so you must never leave your child unattended in a car.
ON and OFF handle cover with your thumb in the direction of ①. It is ok to pull out the handle with four fingers in the direction of ②. Instruction To unlock the child safety lock (LOCK) (The rear door cannot be opened inside the car), move the shift lever of child safety lock to the Stop position in the direction of ②, as shown in the figure.
28 ON and OFF Front window regulator switch ③ Window switch for driver's door. ④ Window switch of passenger door. Rear window regulator switch ⑥ Rear left door window switch. ⑦ Rear right door window switch. Others ① Central lock ON. ② Central lock OFF. ⑤ Glass lock switch. − Switches ① and ② can realize the function of centralized control lock. After Switch ⑤ is pressed down, the windows will be locked and other windows except for the driver’s window cannot be lowered or raised.
Light and Vision Light and Vision Lights ⑥ Left / right steering selection. Rotate the light control handle ① to select on / off of general Turn On and Off the Lights Use the light control handle of the combination switch to control ON / OFF of the lights. light. − Turn the light knob to OFF gear The exterior lights of the car, instrument backlights, the background lights of air conditioning control panel and the background lights of acoustic equipment will be turned off.
Light and Vision 30 When being switched to high beam, the indication will light up. on the meter Rotate fog light selection knob ③ to select the fog light function − Rotate switch to OFF position The front and rear fog lights of the car are turned off. − Rotate the switch to position (some models are equipped with this function) The front fog lights of the car are turned on and the rear fog lights are turned off. At this time, the indication on the meter will light up.
Light and Vision road. do not adjust the illumination distance of the lights too far, for fear that the road users on the opposite side are affected. Flashing Alarm Device The flashing alarm device is used to make the users on any other roads pay more attention to your car in a dangerous situation. The car is in trouble or in an emergency. Tow or towed by any other car.
32 Light and Vision − Turn the toggle lever to its original position, and switch the front headlight to low beam. At this time, the high beam is off. − Turn the toggle lever backward, and the high beam of the headlight will turn on instantaneously. Used to send a signal to the vehicle in front of the car. Description of these functions The operation of the above-mentioned lights can be performed only when the ignition system is turned on.
Light and Vision Rear snow chain operation Sunvisor − Press the switch OFF and the snow chain turns off. The sunvisor for the driver and front passenger can be pulled out of the fixed bracket inside the car and turned to ① of the door. − Press the switch ON and the top light turns on. Makeup mirror Caution! If the roof illumination light is on when the driver leaves the car, it indicates that the door is not closed in place, and please check the closing condition of the door.
34 Light and Vision − Turn the switch upward / downward, there are 5 stop positions to operate 5 kinds of functions, by which the work of the front windshield wiper can be controlled. Position 1 Position 2 Position 3 MIST position OFF position INT position Replacement of Windshield Wiper Blade A good windshield wiper blade can maintain a good view. The wiper will work once. Applicable for use when driving in a drizzling day. Turn off the wipers.
Light and Vision Warning ! In order to prevent from the formation of adhesions, the wiper blade shall be regularly cleaned with a windshield detergent. Under a seriously polluted condition (for example, insect residues)), the wiper blade can be cleaned with a sponge or a piece of cloth. Otherwise, there will be a risk of accident. For the sake of safety, the windshield wiper blade shall be replaced once or twice a year.
36 Light and Vision − Press the four-side positions of MIRROR button, you can choose to adjust the lens of the rearview mirror upward or downward, and make it inclined to left or to right so that the driver can obtain the best effect from the perspective of observation.
Seat and Layout Seat and Layout Adjusting the Front Seat Suitable for: cars with manually adjustable seats Adjust the Seat Seat Adjustment Operating Element Adjust the front and back position of the seat Seats with multiple adjustment functions − Pull handle ① upward, and then continue to push the seat until the seat locking mechanism is engaged. Adjust the inclination of the backrest − Keep the seat backrest in a relaxed state (do not lean on the backrest).
38 Seat and Layout Headrest removal − Press the button. − Pull the Headrest up to the limit position and pull out the headrest. Headrest installation Headrest adjusting button for front seat − Insert the headrest into the guide rail until you hear a jamming sound. The height of the headrest is adjustable. You shall make appropriate adjustments according to your body size.
Seat and Layout When the Rear-row seats is not occupied, turned down the headrest to improve the backward sight. Rear-row Seats Adjust the headrest to the desired position Turn over the Cushion − Grasp both sides of headrest with both hands. The storage space for luggage can be enlarged by turning over the cushions of rear-row seats. − Press the button to pull the headrest upward until it is struck ( in its use position). Headrest removal − Pull headrest up to the limit position.
40 Seat and Layout Front drink holder Level the Rear-row seats cushion Level the cushion Two beverage cans at most can be placed on the front middle armrest. − Hold up the cushion and take out the cushion drawstring ① . − Level the cushion ② to make sure that the latch hook of the cushion is locked in place. In order to make it convenient for the rear-row seats passengers to get on / get off the car, the rear-row seats can be turned forward. At the same time, the seat can be moved forward or backward.
Seat and Layout USB and Power Supply Back-Up Power Supply USB port The stand-by power supply is the +12V power supply provide by the car-mounted electronic equipment. USB interface can be used to charge DC-5V electric appliances, or used as a fixed power supply interface for electric appliances, and can also be used as data transmission interface of relevant equipment.
42 Seat and Layout Open the glove box − Press and hold the glove box switch and open the glove box. Close the glove box − Turn the cover plate upward till it is stuck. Hat-and-Coat hook The Glove Box on the Door Trim Plate. There is a glove box on the door trim panel. Door trim panel with glove box Hat-and-coat hook Warning ! Please be careful not to let the clothes hanging on it ward off the driver's vision of observing the rear.
Drive Drive Warning ! Steering System Please adjust the steering wheel only after the car stops. Otherwise, there is a danger of accident ! Adjust Steering Wheel Position For the sake of safety, the adjustment handle must always be locked backwards, for fear that the position of the steering wheel is changed unintentionally when driving. Otherwise, there is a danger of accident ! Make step-less adjustment to the position of the steering wheel in the direction of height.
Drive 44 ③ ④ ⑤ key into the ignition switch. Sep on the brake pedal and turn the mechanical key to ACC gear (at this time, the vehicle lights can start to work). Then, turn it to “ON” gear to initiate the vehicle completely ( “ready” indicator light on the meter is lit). Put the shift lever on “D” (Drive) or “R” (Reverse) gear, release the handbrake, then the brake pedal, and the vehicle can begin to run. check and confirm the reset parking brake.
Drive gear shift is still unsuccessful for many times, it is necessary to After parking, all electrical switches of the complete vehicle shall make the vehicle repaired. If necessary to brake, just step on the be closed to prevent battery power loss. Take out the negative brake pedal with your right foot to complete the braking. if wire of the auxiliary storage battery if the car will be not used for necessary to accelerate, just apply your strength evenly with your a long time.
46 Drive Parking Brake Operation Release the parking brake − First pull up the parking brake handle and press the button at the same time. and push the brake lever down to the bottom under the condition that the button is pressed. Warning ! Make sure to completely disengage the parking brake to turn off the brake warning light prior to driving.
Drive Warning ! It is set on the auxiliary instrument panel to control the on and off There shall be no people in a locked car, especially no children in it. A locked door will make it more difficult for the rescuers to get in the car in an emergency, thus it may endanger the lives of those to be rescued! of the reversing device. The electronic shifter settings include a Do not leave your child unattended in a car. Otherwise, the child may release the parking brake or pull out the gear.
48 Parking Assist System Parking Assist System Parking Assist System* Backup Camera* It is used to reverse, and it is convenient for the driver to reverse when the image of the car rear is displayed on the display screen. The image of display screen when reversing. When reversing, there are 3 kinds of different color line segments, which indicates the distance between the car and the obstacle. Installing position of backup camera The backup camera is installed on the lower edge of the rear bumper.
Parking Assist System Instruction surrounding conditions of the car at any time. The reversing image function is only used as an auxiliary function to assist the driver in reversing operation. ask the driver to drive carefully when reversing and pay attention to the surrounding conditions of the car, in order to avoid an accident.
50 Parking Assist System door is completely closed. Note: The objects mounted on the back door must not block the camera. Caution! Do not clean the ice and snow on the reversing camera with warm water or hot water. Otherwise, there is a danger of cracking the lens! Don’t use any materials with polishing effect when .the lens are cleaned.
Safe Driving Safe Driving Basic Principles Safety First We put your safety in the most important position. In this paragraph, you will find important information, suggestions and warnings that are beneficial to the safety of you and the passengers. and you shall read them carefully and follow them. Warning ! The Manual contains important information for the driver and the passengers to use the car.
52 Safe Driving Before Driving Each Time: The driver is obliged to ensure that the passengers are safe and the car operates safely. For the safety of you and your passengers, please be sure to meet the following requirements before driving each time: − Ensure that the lighting and the steering signal device on the car can work normally. − Check the inflation pressure of tires. − Ensure that all vehicle windows are clear and transparent to ensure that personnel have a good view.
Safe Driving Correct Sitting Posture Correct Sitting Posture of the Driver The correct sitting posture of the driver is of important for his safety and easy driving. For your own safety and to reduce the risk of injury in a traffic accident, it is recommend that the driver’s headrest be adjusted as follows: − Adjust the position of the steering wheel so that the distance between the steering wheel and the chest is at least 25 cm.
54 Safe Driving emergency braking or in a traffic accident, do not drive the vehicle when the backrest is made leaned backward too much ! Only when the backrest is in a vertical state and the driver has properly fastened the seat belt can the seat belt exert the best protection effect. The greater the backrest is inclined backward, the great the risk of injury occurs due to improper use of seat belt and incorrect sitting posture! Correctly adjust the headrest to achieve its best protection.
Safe Driving in the Rear-row seats must comply with the regulations shown as follows: − Put his feet in the space for the feet in front of the Rear-row seats. − Fasten your seat belt correctly. Adjust Headrest Correctly The correctly adjusted headrest is an important part of the passengers protection system, which can reduce the risk of injuries to the passengers in most accident cases.
56 Safe Driving of injuries in an emergency or if necessary to accelerate and brake. It is necessary to adjust the headrest correctly according to the body size. Do not lie on the Rear-row seats. Do not sit in front of the seat. Do not sit with your side against the seat. Do not lean against the car window. Examples of Incorrect Sitting Posture Do not stretch your feet out of the car window. Incorrect sitting posture may result in the death of or serious injuries to the passengers.
Safe Driving − Make sure that the accelerator pedal and the brake pedal can be freely pressed to the bottom at any times. − Make sure that the pedal can freely return to its original position. Only use foot pads, which can ensure that the pedal area is unobstructed and can be firmly fixed in the space for the feet. When certain brake circuit fails, you must press the brake pedal to the bottom for a longer time in order to make the car stopped.
58 Seat Belt Seat Belt Why Fasten Your Seat Belt Protection function of seat belt It is generally believed that in minor accidents, relevant personnel can support their bodies with their hands This is wrong! The properly fastened seat belts can keep the passengers in the correct sitting posture. A seat belt can reduce an passengers’ kinetic energy significantly. In addition, seat belts can prevent uncontrolled movements from happening. These movements may result in serious injuries.
Seat Belt the rear rows. Otherwise, there is a danger of injuries! Similarly, pregnant women shall always fasten their seat belt. This is the only best protection for an unborn baby. Important Safety Instructions Related to Wearing Seat Belts The properly fastened seat belt will greatly reduce the risk of injuries ! Warning ! The latch of the seat belt can only be inserted into the lock catch of the seat to which it belongs. Otherwise, the protective effect of the seat belt will be affected.
60 Seat Belt The car carrying the passengers who does not fasten his seat belt is driving towards the wall body. collided in the event of a collision accident. The result will lead to serious injuries and even a danger of life. Even if you are driving at a speed between 30 km/h, the force acting on your body can exceed 10,000 Newtons in a crash. It is equivalent to 1-ton gravity (1,000 kg) . The force acting on the physical body is even higher when the car is driving at a higher speed.
Seat Belt In a frontal collision, the improperly-belted passengers can be thrown against the interior components, such as, steering wheel, instrument panel and windshield. The passengers without seat belt fastened may be even thrown of the car All this may cause a risk of injuries and even endanger the life. The driver without seat belt fastened will be thrown forward There is a belief that an passengers’ body can be supported by his/her hands in a minor accident. This is wrong.
62 Seat Belt − Please adjust the front seat and headrest properly before fastening the seat belt. − Insert the tab into the seat belt buckle until a click sound is heard. − Please gently pull your seat belt to check that it is locked in the buckle. The adjustment of headrest and the way of fastening the seat belt Each three-point seat belt comes with an automatic seat belt retractor. This automatic retractor ensures free movement of the belt as it is slowly pulled out.
Seat Belt seat belt is not fastened properly, personal injury may be caused even in minor traffic accidents. Wearing a seat belt too loosely may cause personal injury because it may cause you to come to a sudden stop in an accident as your body continues to move forward due to inertia. Pregnant Women Wearing Three-Point Seat Belt and the Manner of Fastening Seat Belt A pregnant woman wearing a seat belt properly may give her fetus the best protection.
64 Seat Belt − Please adjust the front seat and headrest properly before fastening the seat belt. − Extend the belt slowly and evenly so that it passes over the chest and hip by holding the locking tab. Position the lap belt as low as possible to avoid belt contact with the rounding of the abdominal area. − Insert the tab into the seat belt buckle until a click sound is heard. − Please gently pull your seat belt to check that it is locked in the buckle.
Seat Belt Unbuckle the Seat Belt Safety Belt Pretensioner The red button in the buckle is used to release the seat belt from its buckle. Working Principle of Safety belt Pretensioner For some models, the driver and front passenger seat belts come with pretensioner. The pretensioners help the front seat belts to quickly restrain the passengers by retracting the seat belts when the vehicle is subjected to severe frontal, side and rear collision.
66 Child Safety Protection Child Safety Protection Instructions for Children to Ride Introduction to this Topic Accident statistics reveal that children sitting in the Rear-row seats are safer than sitting in the front passenger seat. Children under the age of 12 should generally be seated in the Rear-row seats. The child seat mounted on the Rear-row seats or the existing seat belt shall be used to protect the children according to their age, height and weight.
Child Safety Protection Child Seat Classification of Child Seats Only the child seats that are officially approved and suitable for children are allowed. The child seat must comply with the GB 27887-2011 standard.
68 Child Safety Protection Group Ⅰ Child Seat Group Ⅱ/Ⅲ Child Seat The combination of suitable child seat and proper use of seat belt may provide protection for your child! The combination of suitable child seat and proper use of seat belt may provide protection for your child! Group II/III front-faced child seat (with backrest) mounted on the Rear-row seats Group I front-faced child seat mounted on the Rear-row seats Infants under 4 years and weighing 9 to 18 kg are suitable to sit in a front-faced
Child Safety Protection For children under 12 years weighing 15-36 kg and under 1.50 m in height, it is best to use a child seat and a three-point seat belt. When installing and using a child seat, comply with the legal requirements and the child seat manufacturer’s instructions. Warning ! The shoulder belt must pass over the middle of the shoulder and come close to the upper body. Never pass over the neck. The lap belt must be positioned over the child's hips and fitted to the body.
70 Intelligent Technology All Wheel Drive All-Wheel Drive All four wheels are driven in AWD mode. Overview The AWD system distributes the driving force to all four wheels. Please read the four-wheel drive state transition. The AWD system is designed for high-power electric motors. This car has extraordinary performance, and shows excellent driving performance on both ordinary and snowy roads. That is why it is necessary to pay attention to some safety instructions.
Maintenance and Cleaning Maintenance and Cleaning Simple Maintenance Applicable to: cars equipped with this audio system Maintenance of Central Controller ignition system. If the problem is still not solved, please visit the KANDI-authorized service shop for repair. Motor and Drive Control System − The user must conduct correct use and maintenance to ensure normal operation of the electric motor.
72 Maintenance and Cleaning − Maintenance and repairing activities should be carried out one minute after power-off, because the device has high voltage in this period. It may cause electric shock accident or damage to the component on the device. The fluid level should reach the HOT MAX mark when it is hot. And if the fluid level is below the HOT MIN mark, add the specified fluid.
Maintenance and Cleaning Measuring the thickness of the friction lining For measuring the brake disc thickness − The wear of the lining can be observed through the observation hole on the caliper, and the thickness of the lining can be measured with a vernier caliper. When the thickness is equal to or less than 2mm, the lining must be replaced with a new one (in addition, the alarm device of lining can be used to judge whether the lining needs to be replaced).
74 Charging Oil filler cap/cable Charging Charging Operation Open the charging port cap − Pull the latch of the charging port cap to the rear of the vehicle, and the cover pops open to expose the charging socket. Operation Process When you need to charge, you may open the switch of the charging port cap to charge.
Charging − Close the charging cover until it locks. 75 ④ When the charging is completed or needs to be terminated, remove the standard plug from the socket of the power supply equipment. ⑤ Press and hold the button on the charging plug to disengage the mechanical locking hook from the corresponding slot, slowly pull the charging plug out of the socket and cover the charging plug. ⑥ Collect the charging cable assembly and place it in the appropriate position in the car.
Charging 76 ① Park the vehicle reliably and appropriately away from the DC charger. ② Park the vehicle reliably and appropriately away from the power supply, and take out the common charging cable assembly and insert the standard plug into the corresponding standard socket of the power supply equipment.
Charging 77 If the vehicle has been driven in the rain, please wipe the body dry before charging. Please note that there shall be no residual rainwater left at the vehicle charging socket-inlet and its adjacent area. Operation Process Please keep the vehicle charging port dry and clean during the charging, and take corresponding preventive measures if necessary. When you need to adopt 110V power, please follow the following steps.
78 Charging The battery constant current function switch is located on the right side of the front compartment. 110V AC socket Warning ! Please use it when the vehicle is parked safely, or by passengers who do not affect the driving of the vehicle. Please ensure that the cab is dry and ventilated, and it is recommended to use it at 0-35 ℃. If the inverter or socket is damaged, please stop using it and immediately contact the dealer for repair.
Check and Refilling Check and Refilling Front Engine Hood Front Engine Hood unlock Open the Front Engine Hood Release the hood. Local view of driver's left legroom Opening handle under hood − Pull the release lever located at the lower left side of the instrument panel in the direction of the arrow. − The hood is ejected from the locking mechanism by spring force. Before opening the hood, make sure that the wiper arm is not lifted up from the windshield. Doing so may cause paint damage.
80 Check and Refilling − Open the front engine hood. − The front engine hood is fixed in the open position by two pneumatic spring support rods. Warning ! If there is steam or coolant coming out of the front compartment, do not open the hood. Doing so may cause a risk of scalding! Wait until there is no more steam or coolant coming out.
Check and Refilling Instruction For the Right-Hand Drive (RHD) * vehicles, some of the containers described below are located on the other side of the front compartment. Close the Front Engine Hood − Pull down the hood until it overcomes the support force of the pneumatic spring support rod. − Then let it go to fall down and lock. Do not press it again! Warning ! For safety reasons, the hood must be always locked securely while driving.
82 Check and Refilling Cooling System Temperate region Coolant It is not allowed to add water to reduce the concentration of coolant in warm seasons or in temperate countries. The proportion of coolant additives should not than 40%. The coolant is used to cool the engine down. Proportion of the coolant additive decides anti-freezing capacity of the coolant in winter. Motor coolant must be changed at intervals specified in the maintenance manual.
Check and Refilling Check the coolant level The coolant level can be visually checked. The coolant level may be properly checked only when the motor is turned off. There is an indicator in the instrument cluster to monitor the coolant level. Nevertheless, it is recommended to check the coolant level directly from time to time. Loss of coolant The loss of coolant is mainly caused by leakage. Please check the cooling system at KANDI-authorized service station immediately. You should not just add coolant.
84 Check and Refilling − Refill the coolant. − Close and screw the cap. The coolant meeting the specified specifications must be added. If the coolant additive G12+ is not available in emergency situations, no other additives shall be filled. In this case, water can only be added first, and then the coolant additive can be added as soon as possible in the correct proportion. Only new coolant can be added. Add coolant to the position marked "F".
Check and Refilling Brake Fluid Check Brake Fluid Level The brake fluid level can be visually checked. However, if the fluid level drops significantly in a short period of time, or falls below the mark "ADD(minimum)", there may be a brake system leakage. If the brake fluid level is too low, the brake fault indicator will also come on. Marking on brake fluid reservoir. Instruction The brake fluid in the brake fluid reservoir is shared by the brake and clutch system. Replace the Brake Fluid.
86 Check and Refilling Only original brake fluid is allowed. KANDI-authorized service station knows about the brake fluid "DOT 4" approved by the manufacturer. The brake fluid must be new. Warning ! Only use the sealed original container to properly store the waste brake fluid to prevent children from reaching, otherwise there will be a risk of poisoning! Too old brake fluid may form bubbles in the brake during hard braking.
Check and Refilling KANDI-authorized service station before the winter comes, and charge it when necessary. Warning ! Know-how is required for all the operations on the battery! Please allow KANDI-authorized service station or professional maintenance shop to perform the operations related to battery, otherwise there is a risk of corrosion and explosion. Do not open the battery! Do not attempt to change the liquid level.
88 Check and Refilling the battery. Do not use damaged battery, otherwise there is a risk of explosion. Please replace the damaged battery in time. Caution! − Now, plug the power cable of the charging device into the power socket first, and then turn on the device. − After the charging process: turn off the charging device, and then unplug the power cable.
Check and Refilling Please read “Warnings for operating battery” before working on a battery. Warning ! Do not charge a frozen battery, otherwise there is a risk of explosion. Replace the Battery. The specifications of the new battery must be the same as those of the used one. The new battery must have the same capacity, voltage (12-volt), current intensity, structure and seal plug. The battery must comply with TL 82506 (December 1997 edition or later) and VW 75073 (August 2001 edition or later).
90 Wheel and Tire Wheel and Tire Wheel Overview moderate speed and corresponding careful driving mode. This will extend the service life of tires. − Be especially careful for the first 500km on new tires. Due to the structural characteristics and tire pattern design, different new tires (Depending on model and manufacturer) have different pattern depths. − When driving along the curb or similar sections, you may only pass at a low speed and at right angles to the curb as far as possible.
Wheel and Tire damaged trim parts, please go to the KANDI-authorized service station to replace them. Tire Service Life However, if you wish to drive in a comfortable way, you may maintain the tire inflation pressure specified for normal vehicle load when running under normal load (up to 3 people). If you want the car to run under maximum load, you must increase the tire inflation pressure to the specified maximum.
92 Wheel and Tire Warning ! Always adjust the tire inflation pressure to adapt the current load of the vehicle. Driving at high speed for a long period of time will make the tire with low inflation pressure frequently deform and squeeze. Which will cause the tires to overheat. And thus may cause tire pattern to split or even burst, resulting into the risk of accidents! Information About Environmental Protection Low tire inflation pressure can increase fuel consumption.
Wheel and Tire Replace the wheels − If you do not want to use the factory-installed tire and rim combination, please consult the KANDI-authorized service station before purchasing a new tire or rim. Tires and rims are important structural parts. The tires and rims approved by KANDI are most suitable for corresponding models, so they play an important role in driving comfort and safety. Knowing tire data makes it easy for you to make the right choice.
94 Wheel and Tire Failure to do so may affect the specified rotational freedom of wheel. Tires, chassis & vehicle body parts, and pipelines may be damaged due to contact friction, which may seriously affect the driving safety. In addition, the driving license of the vehicle may also be canceled because it does not meet the maximum allowable nominal size. And the actual size of the tires approved by KANDI will certainly be able to fit your car.
Wheel and Tire Wheel Nuts The wheel nuts must match the rim. The rim and wheel nut are structurally matched with each other. Therefore, every time the wheel is modified to another rim (such as the rim of a winter tire), the corresponding wheel nut with the correct length and nut shape must be used. This determines the tightness and fixation of the wheels and the function of the braking system. KANDI-authorized service station may teach you how to refit tires, rims and install wheel trim covers.
96 Wheel and Tire Snow Chain When driving in snow, the snow chains can improve the driving performance of vehicle. − Install snow chains only on the rear wheels. − Please note that the maximum speed is 50km / h. For winter road conditions, the snow chains improve not only traction, but also braking performance. For technical reasons, the snow chains are only allowed to be used on some combinations of rim and tire. Please use light and thin snow chains.
Anchor Aid Anchor Aid Replace Wheels Preparation Replace Wheels The process of replacing wheels consists of the following steps. Preparations must be made before replacing wheels. − Before lifting the vehicle, you must loosen the wheel nuts counterclockwise for about one turn. − When a tire is damaged, park the vehicle as far away from traffic as possible. The ground should be level. − Lift the car with a car jack. − Ask all the passengers to get off the vehicle.
98 Anchor Aid The wheel nuts must be clean and easy to screw. When installing tires with directional patterns, you must pay attention to their rotating direction. Warning ! Note: As long as the vehicle is not lifted by the jack, you can only loosen the wheel bolts for about one turn, otherwise there is a danger of accidents! Lift the Car In order to remove the wheels, the vehicle must be lifted by the jack.
Anchor Aid ground), an non-slip mat (such as rubber mat) should be placed under the jack base. Warning ! Proper measures must be taken to prevent the jack base from slipping, otherwise there is a risk of injury! If the vehicle jack is not placed in specified position, it may cause damage to the vehicle.
100 Anchor Aid performance of tire cannot be guaranteed in this case. Be more careful on wet roads. In order to take full advantage of directional tires, replace the damaged tires as soon as possible and make sure that all tires can be turned in the specified direction. Towing a Car Electric Winch It is a tool for pulling a trapped car out of trouble by a steel rope or special cable with one end fixed or pulled. Additional Work There are several additional tasks to be done after replacing the wheels.
Anchor Aid Operation Instruction When the vehicle is in a severe environment, the following steps can be used for self-rescue and rescue. ① First of all, you should check whether the winch is in good condition to start working. When using the winch for the first time or after replacing the wire rope for winch, coat the wire rope with specific lubricant.
102 Anchor Aid drum. It is recommended that you should wear protective insulating clothing and non-slip shoes, and that you should wear a specific hair cover and tuck the long hair into it. Use eye and ear protective items: Wear goggles usually when operating. Wear a face mask if you are working in an environment that produces metal, wood, or chemical dust, etc. At the electric winch operating site, the related personnel should stand firm and keep their balance.
Fuse and Bulb Fuse and Bulb Fuse Replace the Fuse. Fuse must be replaced if it is burned out. − If the fuse has been burned out (which can be identified by a blown metal sheet), replace it with a new fuse with the same specification. All circuits on the vehicle are protected by the fusible fuses. The fuse block with fusible fuses is located at left side of instrument panel. In addition, a label indicating the corresponding fuse location is applied on the fuse block cover of instrument panel.
104 Fuse and Bulb should always be based on the data affixed on the inside of fuse block cover! Front Engine Compartment Fuse Box Some appliances listed on fuse block label are only applicable for special models or optional equipment. Note that the block labels below should be as the same as they were printed and have been changed.
Fuse and Bulb Bulb Replace the Bulbs The bulb is replaced by professionals. External lighting on this vehicle The following bulbs for exterior illumination on vehicle can be replaced by yourself: Headlight: low beam light bulb (halogen light). Headlight: high beam light bulb (halogen light). Headlight: position light bulb. Bulbs on the headlight. The following bulbs must be replaced at professional service station: Turn signal bulbs in the headlights.
106 Fuse and Bulb There is pressure in the bulb and it may explode when it is replaced, so please prevent injury as repairing. The bulb will be very hot when it is operating or just after it goes out, so please wait until the bulb cools down to replace it. When replacing bulb, please take care to prevent sharp edges (including the sharp edges of lights and the sharp edges of adjacent vehicle parts) from causing injury.
Fuse and Bulb Bulbs on the Headlights Replace Low Beam Light Bulb − Remove the rubber rear cover ① of light fixture and then you may see the holder and hold-down spring, remove the hold-down spring and then the bulb. − Replace it with one spare bulb of low beam light, reconnect it with light holder and install the hold-down spring in place to recover the rubber rear cover. − Reinstall the headlight onto vehicle, tighten 4 mounting screws and then reinstall the front bumper.
108 Fuse and Bulb − Remove the front bumper. Use the tool to remove 4 mounting screws from headlight and then remove it. − Remove the rubber rear cover ② of light fixture and you may see the position light holder, then remove the high beam light bulb. − Replace it with one spare bulb of high beam light and reinstall the position light. Close the rubber back cover. − Reinstall the headlight onto vehicle, tighten 4 mounting screws and then reinstall the front bumper.
Fuse and Bulb Bulbs on the Rear Headlight Replace the Rear Turn Signal Bulb Take the right side rear headlight as an example to describe the bulb replacement procedures.(the left side rear headlight bulb replacement procedures are the same). Remove rear headlight − Open the cargo back door until exposing the rear combination light mounting bolts (2 pcs) on the side, then use a cross screwdriver to remove the screws. Hold the light and pull out the combination light rearward.
110 Fuse and Bulb − Install the light fixture forward into quarter panel and secure the fixture with screws. Replace the Brake Light Bulb Remove the rear headlight − Open the cargo back door until exposing the rear combination light mounting bolts (2 pcs) on the side, then use a cross screwdriver to remove the screws. Hold the light and pull out the combination light rearward. Replace the brake light bulb − Rotate the light holder ① counterclockwise, so as to remove the brake light bulb.
Fuse and Bulb Open the cargo back door until exposing the rear combination light mounting bolts (2 pcs) on the side, then use a cross screwdriver to remove the screws. Hold the light and pull out the combination light rearward. Replace the rear fog light bulb − Rotate the light holder ⑤ counterclockwise to remove the rear fog light bulb. Replace it with a spare bulb. Install the rear headlight Install the light fixture forward into quarter panel and secure the fixture with screws.
112 Fuse and Bulb Replace front snow chain bulb Replacement of Rear Snow Chain Bulb Replace the front snow chain bulb Rear snow chain removal port − Remove the front snow chain Open the storage box and then you may see 2 screws. Use a cross screwdriver to loosen the screws counterclockwise. After the screws are loosened, pull down the celling light lightly to remove the front celling light. Then disconnect the celling light connector.
Fuse and Bulb − After the light cover is removed, you may see the inside bulb, then replace it with one spare bulb. Install the middle and rear snow chains − After the bulb is replaced, reinstall the light cover to celling light. When installing, first clamp 2 protruding clips into light body and then press the cover in place. Rear snow chain limiting buckle Remove rear snow chain cover − Insert a flat tip screwdriver into the removal port of light cover and pry it up lightly. Replace the bulb.
114 Technical Data Technical Data Description of Data Data for drive motor The power value of the drive motor is measured in accordance with national standards. Car Characteristic Data Vehicle Identification Number − Engraved on the frame. On the dashboard − Sticked on the left front and front defrosting cover plate of instrument panel. Product Label − Sticked on lower part of body right B-pillar.
Technical Data Car Technical Data Parameters and Specification of Complete Vehicle Model K32 L/W/H (mm) 5441x1870x2088 Wheelbase (mm) 3100 Complete vehicle kerb mass（kg） 1990 Max. gross mass (kg) 2565 Front wheel camber 0.33°±0.5° Kingpin inclination angle N/A Kingpin caster angle 2.67°±1.0° Toe-in of front wheel (mm) 0.2±1.
116 Technical Data Data for Drive Motor Model K32 Model 160V21KW/160V15KW Type AC asynchronous Type Ternary lithium battery Voltage grade 162.8 V Drive motor (front/rear) Power battery Electric quantity 41Kwh Rated power (KW) 21 Mileage（mile） 100 Rated torque (N.m) 58 Maximum torque (N.
Maintenance Maintenance Vehicle Maintenance Maintenance Guidelines Proper car maintenance prevents the car from corrosion for a long time. Common causes for vehicle corrosion are as follows: ① Alkaline substance, dust and damp air are accumulated below the car where it is hard to reach. ② Paint and the undercoat are destroyed by slight collision, or scratches from stones or bricks. ③ Salt or dirt with chemical mixtures from the road increases corrosion.
Maintenance 118 ② Any severe scratch, abrasion and mechanical damage to the surface paint layer will result in bodywork corrosion. Vehicle Wash Make the body cleaner. When cleaning the body, follow these steps: ① Use high pressure water flow to flush the vehicle body surface to remove mud and soil. The water quantity should be appropriate and sufficient to loosen the dirt and wash it away.
Maintenance Windshield Cleaning Solution ① The windshield cleaning solution reservoir is located in the front compartment, and the cleaning solution must be the one with formula suitable for the local climate conditions. ② Do not have the cleaning solution mixed with water, because the water will freeze, resulting in damage to the cleaning solution reservoir and other parts of the washing system.
Maintenance 120 Maintenance of Vehicle Operation and Maintenance of New Vehicle In order to make full use of the vehicle performance, prolong the service life of electric vehicle, enhance the reliability of work and the economy of use. During the break-in period of new vehicle, the operation should follow the following instructions: ① The vehicle should move forward slowly, and it is prohibited to violently accelerate the vehicle and drive the vehicle at maximum speed for a long time.
Maintenance torque of the electric motor (the maximum uphill gradient of the vehicle will decreases), and finally, be automatically disconnected from the power supply for protection. at this moment, the system will recover service after the electric door switch is reset and then turned on.
122 Maintenance Toe-in Adjustment The toe-in can be varied by changing length of the left/right tie rod. During adjustment, first loosen the locknut of the tie rod, and turn the tie rod in clockwise or counterclockwise direction, and re-tighten the locknut after being adjusted to appropriate position. Pay attention that length of the left/right tie rod should not be more than 2mm. Wheel Wheel specification is 265/65R17 112 T, Standard pressure of tire is 250Kpa.
