SawStop ® Contractor Saw Mobile Base OWNER’S MANUAL ! W A RNI NG 1. Ne body ver partsplace 2. fin Al base ways unde gers, r the us toe on a lev e the mo s or oth el su saw bile rface and base er . the . mo bile Raise we Lo 3. Lo saw wer the wh 4. Lowe en it saw be drop r the is raise fore d off using back saw to. slo ! WARNING Never place fingers, toes or other body parts under the mobile base.
Safety 1. Never place fingers, toes or other body parts under the saw when it is raised onto the mobile base. The base may suddenly lower on you and cause a severe injury. 2. Do not attempt to use or move the saw on an inclined surface. The weight of the saw makes it difficult to stop on an inclined surface. Attempting to use or move the saw on an inclined surface could result in a severe injury. 3. Make sure the saw is fully lowered to the ground and stable before operating the saw.
Installing Your Mobile Base Note: The stand for your contractor saw must be fully assembled before installing the mobile base. 1. Locate all of the mobile base components shown on page 1. All of the hardware needed to install the mobile base is located on the mobile base hardware pack (see Fig. 1). In order to easily identify the hardware used in each of the following steps, the different pieces of hardware are numbered on the hardware pack and in the figures.
Installing Your Mobile Base 4. Each end of the wheel support has a cylindrical projection. Mount the wheel support to the left side of the stand by inserting the cylindrical projections into corresponding mounting holes in the legs of the stand, and then securing the support to the stand with two M8 x 20 button head socket screws, two M8 lock washers, and two M8 washers, as shown in Figs. 4a and 4b. Fully tighten the two M8 x 20 button head socket screws using a 5 mm hex key.
Installing Your Mobile Base 6. The caster support must be positioned inside the stand. If your contractor saw is not yet on the stand, then lift the right side of the stand a few inches off the floor and slide the caster support into position between the two right legs, as shown in Fig. 6a. Make sure that the SawStop logo on the support plate is facing up and that the connecting lever is on the inside of the stand.
Installing Your Mobile Base 8. Mount the two casters to the outer corners of the caster support by inserting the threaded shaft on the casters through the corresponding holes in the support and holding the casters in place with two M10.5 x 25 washers, two M10.5 x 17 lock washers and two caster nuts, as shown in Fig. 8. Fully tighten the caster nuts with a 14 mm wrench. 12 11 10 3 inch caster Fig. 8 9. Next, install the linkage bar between the wheel support and the caster support.
Installing Your Mobile Base 11. Locate the release lever and the M8 x 30 hex screw and fully thread the screw into the threaded hole in the release lever (see Fig. 11). threaded hole 14 release lever non-threaded hole Fig. 11 12. The release lever attaches to the foot pedal arm of the wheel support. The release lever includes a nonthreaded hole, roughly in the middle of the lever, that aligns with a threaded hole in the foot pedal arm, as shown in Fig. 12. Place the M10.5 x 14.
Installing Your Mobile Base 14. The end of the release lever opposite the foot pedal includes a slot. Pivot the release lever until the slot aligns with the plastic washer and threaded hole in the middle of the linkage bar. Insert the release lever locking screw through the slot in the release lever and thread it into the hole in the linkage bar, making sure to keep the extension spring on the screw (see Fig. 14). Fully tighten the release lever locking screw with a 5 mm hex key. release lever slot Fig.
Using Your Mobile Base 1. To move your saw with the mobile base, step down on the foot pedal to raise the saw off the floor and onto the wheels (see Fig. 17). Step on the foot pedal until the release lever locking screw slides into the locked position in the release lever. Make sure that your foot does not come into foot pedal contact with the release lever while you step here to raise are stepping on the foot pedal to raise the saw, otherwise the mobile base will not stay in the raised position.
Contractor Mobile Base Exploded View 12 11 3 10 30 25 8 23 8 3 12 11 19 10 29 13 9 14 29 18 20 5 17 Lower 15 ! WARNING 2 24 9 7 32 16 22 34 Never place fingers, toes or other body parts under the mobile base. 33 6 Raise 21 27 7 4 6 27 3 4 5 26 3 ! WARNING 1. Never place fingers, toes or other body parts under the mobile base. 2. Always use the saw and the mobile base on a level surface. 1 26 9 SawStop Contractor Mobile Base 31 3. Lower the saw before use.
Contractor Mobile Base Parts List No. Description Part No. Qty. Complete Mobile Base Assembly MB-CNS-000 1 1 Short Axle M6x67.6 MB-CNS-001 1 2 Long Axle M6x73.8 MB-CNS-002 1 3 M6x16x1.5 Washer MB-CNS-003 4 4 M6 Nylon Hex Nut MB-CNS-004 2 5 M8x20 Button Head Socket Screw MB-CNS-005 4 6 M8x13.6 Lock Washer MB-CNS-006 4 7 M8x18x1.5 Washer MB-CNS-007 4 8 M6x40 Hex Bolt MB-CNS-008 2 9 M6 Flange Lock Nut MB-CNS-009 2 10 M10.5x25 Washer MB-CNS-010 2 11 M10.
Warranty SawStop warrants to the original retail purchaser of the Contractor Saw Mobile Base accompanying this manual that the mobile base will be free from defects in material and workmanship for ONE YEAR from the date of purchase. This warranty does not apply to defects arising from misuse, abuse, negligence, accidents, normal wear-and-tear, unauthorized repair or alteration, or lack of maintenance. Please contact SawStop to take advantage of this warranty.
