Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=128 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 5.
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=128 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 5.120000 mm Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine.
UranosC1-ENcopyA_F1_FM.book Page i Friday, July 26, 2002 5:01 PM What You Can Do With This Machine Color Copying ( p.25) You can switch the color copy mode depending on the type of originals used and the desired finish. Full Color Copy ( Black/White Copy ( p.25) Copies using four colors: yellow, magenta, cyan and black. Single Color Copy ( p.25) Copies in black and white, even when the original is in color. p.25) Copies in the designated color.
UranosC1-ENcopyA_F1_FM.book Page ii Friday, July 26, 2002 5:01 PM Color Copying ( Convert Colors ( p.25) Stamping on Copies ( p.26) Copies by changing a specific color in the original to another color. Erase Specified Color ( p.60) Copies with the date, page numbers, etc. The stamp color can be yellow, red, cyan, magenta, green, blue, and black. p.27) Copies by deleting a specific color in the original. Printed inserts types: • Preset Stamp (p.60) • User Stamp (p.61) • Date Stamp (p.
UranosC1-ENcopyA_F1_FM.book Page iii Friday, July 26, 2002 5:01 PM Adjusting Colors ( p.73) Primary Colors Yellow Green Colors can be created by combining the 3 primary colors: yellow, magenta and cyan. Black can be made by combining yellow, magenta and cyan, however, as there might be some slight differences, "black" will be expressed using a black toner. Red Black Cyan Magenta Blue Adjust Color ( Color Balance ( p.
UranosC1-ENcopyA_F1_FM.book Page iv Friday, July 26, 2002 5:01 PM What You Can Do With This Machine Types of Duplex Copies The functions available may vary according to the options installed. For details "Functions that Require Options" p.4 1-sided 2 Pages 2-sided 1 Page p.46 2-sided 1 Page 2-sided 1 Page p.46 1-sided 4 Pages 2-sided 1 Page p.49 2-sided 2 Pages 2-sided 1 Page p.49 1-sided 8 Pages 2-sided 1 Page p.49 2-sided 4 Pages 2-sided 1 Page p.
UranosC1-ENcopyA_F1_FM.book Page v Friday, July 26, 2002 5:01 PM Combining Multiple Pages onto a Single Page ( p.48) The functions available may vary according to the options installed. For details, see p.
UranosC1-ENcopyA_F1_FM.book Page vi Friday, July 26, 2002 5:01 PM TABLE OF CONTENTS What You Can Do With This Machine ... i What You Can Do With This Machine ................................................................. iv Notice ......................................................................................................................1 How to Read this Manual ......................................................................................
UranosC1-ENcopyA_F1_FM.book Page vii Friday, July 26, 2002 5:01 PM Stack ........................................................................................................................ 42 Staple ....................................................................................................................... 43 Duplex ...................................................................................................................... 46 1 Sided Combine........................................
UranosC1-ENcopyA_F1_FM.book Page viii Friday, July 26, 2002 5:01 PM 5. User Tools (Copier/Document Server Features) User Tools Menu (Copier/Document Server Features) .................................... 91 Accessing the User Tools (Copier/Document Server Features) ..................... 97 Exiting From the User Tools..................................................................................... 97 General Features 1/5 ....................................................................................
UranosC1-ENcopyA_F1_FM.book Page 1 Friday, July 26, 2002 5:01 PM Notice Do not make copies of any item for which copying is prohibited by law. Copying the following items is normally prohibited by local law: Bank bills, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licenses. The color copy samples in this book may differ slightly from the actual copies due to printing effects. The color on each Color key may differ slightly from that of the actual copy.
UranosC1-ENcopyA_F1_FM.book Page 2 Friday, July 26, 2002 5:01 PM How to Read this Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section in the General Settings Guide.
UranosC1-ENcopyA_F1_FM.book Page 3 Friday, July 26, 2002 5:01 PM Machine Types This machine comes in two models which vary by copy speed. To make sure which model you have, see the inside front cover of this manual.
UranosC1-ENcopyA_F1_FM.
UranosC1-ENcopyA_F1_FM.book Page 5 Friday, July 26, 2002 5:01 PM Control Panel Note ❒ This illustration shows the Control Panel of the machine with options fully installed. 1. Screen Contrast knob 5. Color Circle Adjusts the brightness of the display panel. Refer to this when adjusting colors. ⇒ p.73 “Color Adjustment” 2. {User Tools/Counter}} key 6. Display panel • User Tools Press to change the default settings and conditions to meet your requirements.
UranosC1-ENcopyA_F1_FM.book Page 6 Friday, July 26, 2002 5:01 PM Important ❒ Do not turn the main power off while the main power indicator is flashing. The hard disk may malfunction. 17. {#}} key Press to enter a value. 18. Number keys Use to enter the desired number of copies and data for selected modes. 13. Operation switch 19. Color Selection Key Press this switch to turn the power on (the On indicator goes on). To turn the power off, press this switch again (the On indicator goes off).
UranosC1-ENcopyA_F1_FM.book Page 7 Friday, July 26, 2002 5:01 PM 1. Placing Originals Originals Sizes and Weights of Recommended Originals ❖ Metric version Where Original Is Placed Original Size Original Weight Exposure glass Up to A3 -- Document feeder 1-sided originals: 40 – 128g/m2 A3L – A5KL 2-sided originals: 52 – 105g/m2 A3L – A5KL ❖ Inch version Where Original Is Placed Original Size Original Weight Exposure glass Up to 11" × 17" -- Document feeder 1-sided originals: 11 – 34 lb.
UranosC1-ENcopyA_F1_FM.
UranosC1-ENcopyA_F1_FM.book Page 9 Friday, July 26, 2002 5:01 PM Originals ❖ Exposure glass Reference position A3 Horizontal size Vertical size 1 Maximum Scanning area A3 (297x420mm) 11"x17" (279x432mm) A4 A3 CP01AEE ❖ Document feeder Sizes difficult to detect It is difficult for the machine to detect the sizes of the following originals, so select the paper size manually.
UranosC1-ENcopyA_F1_FM.book Page 10 Friday, July 26, 2002 5:01 PM Placing Originals Missing Image Area Even if you correctly place originals in the document feeder or on the exposure glass, margins of a few millimeters on all four sides of the original might not be copied. 1 1. 0 - 4 mm, 0”- 0.16” 2. 0 - 4 mm, 0”- 0.16” 10 3. 0 - 4 mm, 0”- 0.16” 4. 2 - 6 mm, 0.08”- 0.
UranosC1-ENcopyA_F1_FM.book Page 11 Friday, July 26, 2002 5:01 PM Originals Direction-fixed paper or 2-sided paper Direction-fixed (top to bottom) or 2-sided paper (e.g., letterhead paper, punched paper, or copied paper) might not be printed correctly depending on how the originals and paper are placed. Set "Letterhead setting" in system settings, and then place the original and paper as shown below. ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 12 Friday, July 26, 2002 5:01 PM Placing Originals Placing Originals Note ❒ Place originals after correction fluid and ink have completely dried. Not taking this precaution could dirty the exposure glass with marks that will be copied. 1 B Select the original orientation. Standard Orientation A Make sure that ed. is select- Reference For document sizes you can set. ⇒ p.7 “Originals”. Original Orientation You can set the original orientation in the following ways.
UranosC1-ENcopyA_F1_FM.book Page 13 Friday, July 26, 2002 5:01 PM Placing Originals Placing Originals on the Exposure Glass Placing Originals in the Document Feeder A Lift Settings should be made in the following situations: the exposure glass cover or the document feeder. Important ❒ Do not open the exposure glass cover or the document feeder forcefully. Otherwise, the cover of the document feeder might open or be damaged.
UranosC1-ENcopyA_F1_FM.book Page 14 Friday, July 26, 2002 5:01 PM Placing Originals A Set the document guide to the original size. B Align the edges of the original and place it on the document feeder (ADF) with the side to be copied facing up. 1 B Select [Batch], and then press [OK]. Note ❒ When [Batch] is not displayed, change the settings in ⇒ p.105 “Switch to Batch (SADF)” C Place the first part of the original, then press the {Start} } key.
UranosC1-ENcopyA_F1_FM.book Page 15 Friday, July 26, 2002 5:01 PM Placing Originals A Press [Special Original]. Mixed Size mode When you place different size originals which have the same width in the document feeder at the same time, the machine automatically checks the size of the originals and makes copies. B Press [SADF]. C Press [OK]. D Place one page of an original, and then press the {Start} } key. The Auto Feed indicator is shown on the display.
UranosC1-ENcopyA_F1_FM.book Page 16 Friday, July 26, 2002 5:01 PM Placing Originals B Press [Mixed Size], and then press [OK]. Placing Custom Size Originals When placing custom size originals in the document feeder, specify the size of the originals. 1 C Align the rear and left edges of the originals as shown in the illustration. 1 A4 Note ❒ Paper that has a vertical length of 105-297 mm (4.2" – 11.6") and a horizontal length of 128-432 mm (5.1" – 17.0") can be placed with this function.
UranosC1-ENcopyA_F1_FM.book Page 17 Friday, July 26, 2002 5:01 PM 2. Copying Basic Procedure A When the machine is set for user codes, enter a user code (up to 8 digits) with the number keys, and then press the {#} } key. The machine is ready to copy. Reference For Users Code, see ⇒ General Settings Guide, “Key Operator Tools”. B Make sure that "Ready" is displayed on the screen. If any other function is displayed, press the {Copy} } key.
UranosC1-ENcopyA_F1_FM.book Page 18 Friday, July 26, 2002 5:01 PM Copying Auto Start Copy starts automatically when the machine is ready for copy. A Set the copy contents while “Please wait.” is displayed. 2 B Set the original. C Press the {Start}} key. The {Start} } key lamp will flash. Interrupt Copy Use this function if you wish to interrupt a long copy job to make urgently needed copies. Limitation ❒ You cannot use the Interrupt Copy function when scanning fax originals.
UranosC1-ENcopyA_F1_FM.book Page 19 Friday, July 26, 2002 5:01 PM Basic Procedure Job Preset You can set up the next copy content during copy. If a long copy job is in progress and you do not wish to wait for it to finish, you can use this function to set up the next copy job in advance. When the current copy job is finished, your copy job will be started automatically. 2 A Press [Next Job] when "Copying" is shown. B Set up the next copy job.
UranosC1-ENcopyA_F1_FM.book Page 20 Friday, July 26, 2002 5:01 PM Copying Copying from the Bypass Tray The optional bypass tray is required to use this function. Use the bypass tray to copy onto special paper (OHP transparencies, label paper (adhesive labels), thick paper (for example: postcards and envelopes), thin paper), and copy paper that cannot be loaded in the paper trays. 2 Preparation When the Duplex unit is attached, the default setting is [1 Sided→ →2 Sided].
UranosC1-ENcopyA_F1_FM.book Page 21 Friday, July 26, 2002 5:01 PM Copying from the Bypass Tray B Insert the paper with the side you want to copy facing down until you hear the beep, and align the paper guide to the paper size. C Select the type and size of the paper. When copying onto standard size paper A Press the {#} } key. B Press [Select Size]. C Select the paper size. D Press [OK]. 2 When copying onto custom size paper 1.
UranosC1-ENcopyA_F1_FM.book Page 22 Friday, July 26, 2002 5:01 PM Copying ❒ To register the custom size entered, press [Program] and then press [Exit]. 2 E Press [OK]. When copying onto special paper A Press the {#} } key. B Select paper type in "Special paper". C Press [OK]. When copying onto envelopes Note ❒ When placing an original on the exposure glass, place the original with the bottom line aligned to the left scale.
UranosC1-ENcopyA_F1_FM.book Page 23 Friday, July 26, 2002 5:01 PM Copying from the Bypass Tray When Copying on the Back Side of Paper ❖ Top to Bottom Using the Bypass Tray, you can make copies on the back side of pages that have already been copied on the front side. 2 Note ❒ Do not use paper that has been used in other copying machines or printers. ❒ Copies made on the back side of paper should be originals that have a low image area ratio, such as text originals.
UranosC1-ENcopyA_F1_FM.book Page 24 Friday, July 26, 2002 5:01 PM Copying Making A3, 11" × 17" Full Bleed Copies You can make A3, 11" × 17" full bleed copies with 12" × 18" paper. This is useful for making A3, 11" × 17" size copies with a colored background (e.g. catalogues). 2 1. A3, 11" × 17" size Original 2. In standard copy mode, margins 3. 12" × 18" Full Bleed Copy 4. Cut around the margins to pro- appear on copies duce a full image Note ❒ This function can be used with 12" × 18" paper.
UranosC1-ENcopyA_F1_FM.book Page 25 Friday, July 26, 2002 5:01 PM Color Functions Color Functions Selecting a Color Mode Select a Color mode that best suits your originals and copying requirements. Reference For color images ⇒ p.i “What You Can Do With This Machine ” The following basic functions are explained in this section. ❖ Auto Color Select Judges the color of the original automatically, and copies either in full color or black/white.
UranosC1-ENcopyA_F1_FM.book Page 26 Friday, July 26, 2002 5:01 PM Copying When the {Two-color} } key is selected A Select either [Two Color] or [Red & Black]. When [Red & Black] is pressed 2 A Press [OK]. When [Two Color] is pressed A Press [Change Color Setting]. B Press [Black Portion], and then select the color to be replaced by black. Note ❒ When selecting a color from the user colors, press [User Color].
UranosC1-ENcopyA_F1_FM.book Page 27 Friday, July 26, 2002 5:01 PM Color Functions A Press [User Color]. B Select from the registered colors, then press [OK]. Note ❒ You can cancel the selection by pressing the selected (highlighted) key. ❒ You can erase 4 colors at once. G After selecting all the colors to be E Press [OK] after selecting all the H Set F Set the originals, and then press Erase Color Color Background You can copy by erasing a certain color in the image of the original.
UranosC1-ENcopyA_F1_FM.book Page 28 Friday, July 26, 2002 5:01 PM Copying Selecting from the [User Color] A Press [User Color]. B Select a registered color, and then press [OK]. E Set the original, and then press the {Start} } key.
UranosC1-ENcopyA_F1_FM.book Page 29 Friday, July 26, 2002 5:01 PM Copy Functions Copy Functions Adjusting Copy Image Density There are three types of adjustment available: ❖ Auto Image Density The machine automatically adjusts the image density. Manual image density A Press [Auto Image Density] to cancel it. 2 B Press [Lighter] or [Darker] to adjust the image density. ❖ Manual image density You can adjust the density of the overall original in 9 steps.
UranosC1-ENcopyA_F1_FM.book Page 30 Friday, July 26, 2002 5:01 PM Copying Selecting Original Type Setting Select one of the following 6 types to match your originals: ❖ Text Select this mode when your originals contain only text (no pictures). 2 ❖ Text/Photo Select Text/Photo when your originals contain photographs or pictures with text. ❖ Pale Select this mode for originals that have lighter lines written in pencil, or for faint copied slips. The faint lines will be clearly copied.
UranosC1-ENcopyA_F1_FM.book Page 31 Friday, July 26, 2002 5:01 PM Copy Functions Selecting Copy Paper There are two ways to select copy paper: ❖ Auto Paper Select The machine selects a suitable size of copy paper automatically based on the original size and the reproduction ratio. 2 ❖ Manual Paper Select Choose the tray containing the paper you wish to copy onto: a paper tray, bypass tray or large capacity tray (LCT). Reference ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 32 Friday, July 26, 2002 5:01 PM Copying Auto Paper Select A Make sure that [Auto Paper Select] is selected. 2 Note ❒ Trays with a key mark will not be automatically selected. ⇒ "Paper Size Settings" in the General Settings Guide Manual Paper Select A Select the paper tray, bypass tray or large capacity tray (LCT). The indicator corresponding to the selected paper tray is highlighted. Reference ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 33 Friday, July 26, 2002 5:01 PM Copy Functions - Rotated copy If the direction in which your original is placed (L or K) is different from that of the paper you are copying onto, this function rotates the original image by 90° and fits it on the copy paper. This function works when Auto Paper Select or Auto Reduce/Enlarge is selected. ⇒ p.31 “Auto Paper Select” 2 R R Note ❒ The default setting for "Auto Tray Switching" is "With image rotation".
UranosC1-ENcopyA_F1_FM.book Page 34 Friday, July 26, 2002 5:01 PM Copying Preset Reduce/Enlarge You can select a preset ratio for copying. 2 Note ❒ When making reduced copies from A3 or B4 originals to A4 OHP transparencies, set the OHP transparencies in tray 1 in the K direction and use the Auto Reduce/Enlarge function. ⇒ p.36 “Auto Reduce/Enlarge” A Press [Reduce/Enlarge]. ❖ Base Point The base point of Reduce/Enlarge differs depending on how the original is scanned.
UranosC1-ENcopyA_F1_FM.book Page 35 Friday, July 26, 2002 5:01 PM Copy Functions - Create Margin Mode Use "Create Margin" to reduce the image to 93% of its original size with the center as reference. You can register this function in a shortcut key on the initial display. By combining it with the Reduce/Enlarge function, you can also provide the Reduce/Enlarge copy with a margin. Zoom You can change the reproduction ratio in 1% steps. 2 Reference Related Initial Settings A B ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 36 Friday, July 26, 2002 5:01 PM Copying Note ❒ To change the ratio in 1% steps, just press [n n] or [o o]. To change the ratio in 10% steps, press and hold down [n n] or [o o]. ❒ If you have incorrectly entered the ratio, readjust the ratio with [n n] or [o o]. 2 To enter the ratio with the number keys A Press [Mag. Ratio]. B Enter the desired ratio with the number keys. C Press [#]. D Press [OK].
UranosC1-ENcopyA_F1_FM.book Page 37 Friday, July 26, 2002 5:01 PM Copy Functions E Enter the length of the copy with Size Magnification This function calculates an enlargement or reduction ratio based upon the lengths of the original and copy. Ainch ainch the number keys, and then press [#]. Note ❒ To change the length after pressing [#], select [Original] or [Copy] and enter the desired length. 2 F Press [OK]. G Press [OK]. H Place your original, and then press the {Start} } key.
UranosC1-ENcopyA_F1_FM.book Page 38 Friday, July 26, 2002 5:01 PM Copying A Press [Reduce/Enlarge]. D Press [OK]. E Place your originals, and then press the {Start} } key. Directional Size Magnification (inch) 2 B Press [Specifd. Ratio]. C Press [Direct. Mag.%]. The suitable reproduction ratios will be automatically selected when you enter the horizontal and vertical lengths of the original and copy image you require. To enter the ratio with the number keys A Press [Horizontal].
UranosC1-ENcopyA_F1_FM.book Page 39 Friday, July 26, 2002 5:01 PM Copy Functions A Press [Reduce/Enlarge]. Sort The machine can scan your originals into memory and automatically sort the copies. Reference Related Initial Settings B Press [Specifd. Ratio]. C Press [Dirc.Size Mag.In]. D Enter the horizontal size of the original with the number keys, and then press [#]. E Enter the horizontal size of the copy with the number keys, and then press [#]. 2 ⇒ p.106 “Select Stack Function” ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 40 Friday, July 26, 2002 5:01 PM Copying Note ❒ The paper sizes that can be used in the Rotate Sort function are as follows. 2 Metric version A4, B5 Inch version 81/2" × 11", 51/2" × 81/2" ❒ To use the Rotate Sort function, two paper trays with paper identical in size and different in direction (KL) are required. ❒ This function can be used only when optional finisher is not installed.
UranosC1-ENcopyA_F1_FM.book Page 41 Friday, July 26, 2002 5:01 PM Copy Functions C Place your originals. Note ❒ When placing an original on the exposure glass, start with the first page to be copied. When placing an original in the document feeder (ADF), set so that the first page is on the top. ❒ After scanning the entire original from the exposure glass or through the document feeder, press [#]. D Press the {Start}} key.
UranosC1-ENcopyA_F1_FM.book Page 42 Friday, July 26, 2002 5:01 PM Copying Stack B Enter the number of copies with Copies can be assembled with each page placed. C Place the number keys. 2 ❖ Shift Stack • The optional 500-Sheet finisher, 1000-Sheet Finisher or Shift Sort Tray is required to use this function. This function groups copies of each page in a multi-page original together. Every other page stack is shifted for ease of separation.
UranosC1-ENcopyA_F1_FM.book Page 43 Friday, July 26, 2002 5:01 PM Copy Functions Staple An optional finisher and the bridge unit are required to use this function. Each copy set can be stapled together. 2 Note ❒ You cannot use the Bypass Tray with this function. Stapling position and original setting Place all the originals in the automatic document feeder (ADF) in the orientation in which they can be read normally.
UraC1copy_EN_Chapter-2 Page 44 Wednesday, July 31, 2002 1:48 PM Copying ❖ 1000-Sheet Finisher Original location Exposure glass Document Feeder Stapling position K Top 2 L Bottom K L Left 2 K *1 L Top 2 K *1 44 L Not available for paper size larger than A4.
UranosC1-ENcopyA_F1_FM.book Page 45 Friday, July 26, 2002 5:01 PM Copy Functions A Select one of the stapling positions. ❖ 500-Sheet Finisher 2 Note ❒ The stapling position will be fixed to “Top”. ❖ 1000-Sheet Finisher Note ❒ When you select the stapling position, Sort mode is automatically selected. Reference ⇒ p.43 “Stapling position and original setting” B Enter the number of copy sets with the number keys. C Place your originals, then press the {Start}} key.
UranosC1-ENcopyA_F1_FM.book Page 46 Friday, July 26, 2002 5:01 PM Copying Duplex There are two types of duplex. ❖ 1 Sided → 2 Sided Copies two 1–side pages on one 2– sided page. 2 Note ❒ You cannot use the bypass tray with this function. ❒ The paper weight that can be used with duplex copying is 64~105g/m2 (17~28 lb). Original Direction and Completed Copies 1 1 2 2 The resulting copy image will differ according to the direction in which you place your original (widthwise K or lengthwise L ).
UranosC1-ENcopyA_F1_FM.book Page 47 Friday, July 26, 2002 5:01 PM Copy Functions A Press [Dup./Combine/Series]. Originals and Copy Direction You can select the orientation. • Top to Top 2 Duplex1 B Select ([1 Sided]/[2 Sided]) for "Orig- • Top to Bottom inal", and then press ([1 Sided]/[2 Sided]) for "Copy". Duplex2 Note ❒ To change the copy orientation, press [Orientation]. ⇒ p.47 “Originals and Copy Direction” C Press [OK].
UranosC1-ENcopyA_F1_FM.book Page 48 Friday, July 26, 2002 5:01 PM Copying Open to Top S Originals 1 Sided Combine Combine several pages on one side of a sheet. ❖ 1 Sided 2 Pages → Combine 1 Side Copies two 1-sided originals to one side of a sheet. 2 1 2 1 ❖ Placing Originals (Originals Placed in the Document Feeder) Originals read from left to right 2 1 2 3 4 1 2 3 4 Combine5 ❖ 1 Sided 8 Pages → Combine 1 Side Copies eight 1-sided originals to one side of a sheet.
UranosC1-ENcopyA_F1_FM.book Page 49 Friday, July 26, 2002 5:01 PM Copy Functions B Press ([1 Sided]/[2 Sided]) for "Original", and then press [Combine 1 Side] for "Copy". ❖ 1 Sided 8 Pages → Combine 2 Side Copies eight 1-sided originals to one sheet with four pages per side. 1 2 7 1 2 5 6 3 4 7 8 1 2 2 8 GCSHVYAE Reference ⇒ p.47 “Originals and Copy Direction” C Select the number of originals to combine, and then press [OK]. D Select the paper. E Press [OK].
UranosC1-ENcopyA_F1_FM.book Page 50 Friday, July 26, 2002 5:01 PM Copying ❖ 2 Sided 8 Pages → Combine 2 Side Copies four 2-sided originals to one sheet with four pages per side. A Press [Dup./Combine/Series]. 1 3 5 2 2 7 4 6 8 1 2 5 6 3 4 7 8 1 2 B Press ([1 Sided]/[2 Sided]) for "OrigGCSHVY2E 1. Front 2. Back inal", and then press [Combine 2 Side] for "Copy". ❖ 2 Sided 16 Pages → Combine 2 Side Copies eight 2-sided originals to one sheet with eight pages per side.
UranosC1-ENcopyA_F1_FM.book Page 51 Friday, July 26, 2002 5:01 PM Copy Functions Series Copies You can use this function only when you are making a copy from the Exposure Glass. Separately copies the front and back of a 2–sided original or the two facing pages of a bound original onto two sheets. ❖ Book→ →1 Sided You can make one-sided copies from two facing pages of a bound original (book). 1 2 1 2 ❖ Front&Back→ →2 Sided Copies each two-page spread original as it is onto both sides of a sheet.
UranosC1-ENcopyA_F1_FM.book Page 52 Friday, July 26, 2002 5:01 PM Copying A Press [Dup./Combine/Series]. ❖ Specified Area Repeat Repeatedly copies a specified portion of the image. Decide the base point of the area, specify the length and the width, and then specify the location of the area. Reference Related Initial Settings 2 B Press [Series]. C Select ([Book→ →1 Sided]/[Book→ →2 Sided]/[Front&Back→ →2 Sided]) and press [OK]. D Press [OK]. E Make sure that [Auto Paper Select] is selected.
UranosC1-ENcopyA_F1_FM.book Page 53 Friday, July 26, 2002 5:01 PM Copy Functions A Select the size of the copy paper and the reproduction ratio. B Press [Edit/Color Creation]. A Specify the location of the area's base point (X1, Y1), and its length and width (X2, Y2). Note ❒ You can set any value in the range of X1: 0~412mm (0.8”~16.2”), X2: 20~432mm (0.8”~17”), Y1: 0~277mm (0.8”~10.8”), and Y2: 20~297mm (0.8”~11.6”). 2 B Select the size of the copy paper and the reproduction ratio.
UranosC1-ENcopyA_F1_FM.book Page 54 Friday, July 26, 2002 5:01 PM Copying Double Copies Reference Related Initial Settings One original image is copied twice on one copy as shown in the illustration. ⇒ p.102 “Double Copies Separation Line” A Press [Edit/Color Creation]. B Press [Edit Image]. C Press [Double Copies]. D Press [OK]. E Press [OK]. F Select the paper. G Place your originals, and 2 Note ❒ You cannot use the bypass tray with this function.
UranosC1-ENcopyA_F1_FM.book Page 55 Friday, July 26, 2002 5:01 PM Copy Functions ❖ Inch version Original Original size and direction placed on: Exposure glass 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL Document feeder 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 10" × 14"L, 51/2" × 81/2"KL A Select the paper. B Press [Edit/Color Creation]. Positive/Negative If your original is black and white, copy images are inverted. 2 R R GCHATN1E C Press [Edit Image]. D Press [Centring]. E Press [OK]. F Press [OK].
UranosC1-ENcopyA_F1_FM.book Page 56 Friday, July 26, 2002 5:01 PM Copying A Press [Edit/Color Creation]. Margin Adjustment You can shift the image to the left, right, top or bottom to make a binding margin. 2 A B Press [Edit Image]. C Press [Positive/Negative]. D Press [OK]. E Press [OK]. F Select the paper. G Place your originals, press the {Start} } key. Reference Related Initial Settings and then Mirror Copies by reversing the image from left to right, as reflected in a mirror.
UranosC1-ENcopyA_F1_FM.book Page 57 Friday, July 26, 2002 5:01 PM Copy Functions A Press [Edit/Color Creation]. Erase This func tion erase s the c enter and/or all four sides of the original image. This function has the following three types: B Press [Erase/Margin Adj.]. C Press [Margin Adjustment]. D Set a binding margin for a front 2 ❖ Border This mode erases the edge margin of the original image. page.
UranosC1-ENcopyA_F1_FM.book Page 58 Friday, July 26, 2002 5:01 PM Copying ❖ Center/Border This mode erases both the center and edge margins of the original image. Border Erase A Press [Edit/Color Creation]. 2 Reference The erase width is set to 10mm (0.4”) at default settings. You can change this settings with the User Tools. ⇒ p.101 “Erase Center Width” ⇒ p.101 “Erase Border Width” B Press [Erase/Margin Adj.]. C Press [Erase]. D Set the erase border width.
UranosC1-ENcopyA_F1_FM.book Page 59 Friday, July 26, 2002 5:01 PM Copy Functions Selecting [Diff. Width] Center/Border Erase A Press [Diff. Width]. A Press [Edit/Color Creation]. 2 B Press the key for the border you wish to change and set an erase border width with [n n] and [o o]. C Press [OK]. E Press [OK]. F Place your originals, and then press the {Start} } key. Center Erase A Press [Edit/Color Creation]. B Press [Erase/Margin Adj.]. C Press [Erase]. D Press [Center/Border].
UranosC1-ENcopyA_F1_FM.book Page 60 Friday, July 26, 2002 5:01 PM Copying F Press [OK]. G Place your Stamp Position and Original Direction originals, and then press the {Start} } key. Preset Stamp 2 Messages that you use frequently can be stored in the machine's memory and stamped on copies. GCSTMP5E One of the following eight messages can be stamped on copies with a frame around it: "COPY", "URGENT", "PRIORITY", "For Your Info.", "PRELIMINARY", "For Internal Use Only", "CONFIDENTIAL", "DRAFT".
UranosC1-ENcopyA_F1_FM.book Page 61 Friday, July 26, 2002 5:01 PM Copy Functions B Press [Stamp]. C Press [Preset Stamp]. D Select the desired message. E Press [All Pages] or [1st Page only] to User Stamp Copies with the registered stamp. select the print page. Note ❒ You can change the color, position, size, and density of the stamp. ⇒ p.61 “Changing the stamp color” ⇒ p.61 “Changing the stamp position, size and density” F After you specify all the desired settings, press [OK]. G Press [OK].
UranosC1-ENcopyA_F1_FM.book Page 62 Friday, July 26, 2002 5:01 PM Copying Reference Related Initial Settings ⇒ p.104 “Stamp Position 1 - 4” ⇒ p.104 “Stamp Format 1 - 4” ⇒ p.104 “Stamp Color : 1 - 4” A Register a user stamp. 2 Reference ⇒ p.62 “To program the user stamp” B Press [Edit/Color Creation]. G After making all settings, press [OK]. H Press [OK]. I Set the original, {Start} } key. then press the Changing the stamp color A Press [Stamp Color]. B Select the stamp color, then press [OK].
UranosC1-ENcopyA_F1_FM.book Page 63 Friday, July 26, 2002 5:01 PM Copy Functions B Press the {User Tools/Counter}} key. C Press [Copier/Document Server Features]. T h e m ai n m e n u o f t h e C o p i er/Document Server Features appears. D Press [Stamp]. E Press [User Stamp]. F Press [Program/Delete Stamp]. G Press [Program] and press the stamp number (1–4) you want to program. Note ❒ Stamp numbers with m already have settings in them.
UranosC1-ENcopyA_F1_FM.book Page 64 Friday, July 26, 2002 5:01 PM Copying To delete the user stamp Date Stamp Important ❒ You cannot restore a deleted stamp. You can select from the following styles. A Make sure that the machine is in 2 Copy mode. B Press the {User Tools/Counter}} key. C Press [Copier/Document Server]. D Press [Stamp]. E Press [User Stamp]. F Press [Program/Delete Stamp]. G Press [Delete], then press the stamp number (1–4) you want to delete.
UranosC1-ENcopyA_F1_FM.book Page 65 Friday, July 26, 2002 5:01 PM Copy Functions Note ❒ You cannot use the bypass tray with this function. Reference Related Initial Settings ⇒ p.104 “Font” ⇒ p.104 “Size” ⇒ p.104 “Superimpose” ⇒ p.104 “Stamp Position” ⇒ p.104 “Stamp Color” ⇒ General Settings Guide “Timer Setting” A Press [Edit/Color Creation]. E After all the settings are complete, press [OK]. F Press [OK]. G Set the original, {Start} } key.
UranosC1-ENcopyA_F1_FM.book Page 66 Friday, July 26, 2002 5:01 PM Copying Page Numbering Stamp position and original orientation Use this function to print page numbers on your copies. 2 There are six types of Page Numbering (n is the total number of pages in your original): • P1,P2,…Pn • 1/n,2/n,...n/n • -1-,-2-,...-n• P.1,P.2,...P.n • 1, 2…n • 1-1,1-2,..1-n GCSTMP8E Note ❒ You cannot use the bypass tray with this function. ❒ The default stamp color is black.
UranosC1-ENcopyA_F1_FM.book Page 67 Friday, July 26, 2002 5:01 PM Copy Functions A Press [Edit/Color Creation]. Changing the stamp position A Press [Change]. B Select the desired position, and then press [OK]. 2 Specify the first printing page and start number B Press [Stamp]. C Press [Page Numbering]. D Select the format. If you selected (P1,P2…, -1-,-2-…, P.1, P.2…, 1, 2…, ) Note ❒ Below explains the example when (P1, P2...) is selected. The steps are the same for /other cases.
UranosC1-ENcopyA_F1_FM.book Page 68 Friday, July 26, 2002 5:01 PM Copying E Press [Last Number], and then enter the page number at which to stop numbering with the number keys, then press the {#} } key. D Press [Numbering from/to], and then en ter the p ag e nu mb er fr om which to start numbering with the number keys, and then press the {#} } key. E Press [Last Number], and then enter the page number at which to stop nu mbering w ith th e number keys, then press the {#} } key.
UranosC1-ENcopyA_F1_FM.book Page 69 Friday, July 26, 2002 5:01 PM Copy Functions If you selected (1-1, 1-2,…) A Press the right [Change]. B Press [First Printing Page], and then enter the original sheet number from which to start numbering with the number keys. F If all the page designation is complete, press [OK]. G Press [OK]. Covers 2 Using this function, you can add cover sheets or designate certain pages to be copied on slip sheets.
UranosC1-ENcopyA_F1_FM.book Page 70 Friday, July 26, 2002 5:01 PM Copying B Press ([Front Cover]/[Front/Back Cov- • Blank er]). C Select [Copy] or [Blank] for the cov1 2 2 3 1 2 3 ❖ Front/Back Covers The first and last pages of your original are copied on separate paper for use as covers. • Copy er sheet. D Select the paper tray which contains the sheet paper to copy the originals, and then press [OK]. E Place your originals in the document feeder, and then press the {Start} } key.
UranosC1-ENcopyA_F1_FM.book Page 71 Friday, July 26, 2002 5:01 PM Copy Functions ❖ When using OHP transparencies set on the bypass tray • Copy 2 1 2 2 1 1 2 • Blank 2 1 12 Note ❒ When not copying onto slip sheets, the sheets will not be counted as copies. A Press [Cover/Slip Sheet]. B Press [Slip Sheet]. C Select [Copy] or [Blank], and then press [OK]. D Select the paper tray which contains the sheet paper to copy the originals. E Place your originals, and then press the {Start} } key.
UranosC1-ENcopyA_F1_FM.book Page 72 Friday, July 26, 2002 5:01 PM Copying Storing Originals in the Document Server The Document Server enables you to save documents in the machine memory and then print them as you want. B Enter a file name, user name, or password if necessary. Important ❒ Data stored in the machine might be lost if some kind of failure occurs. The supplier shall not be responsible for any damage that might result from the loss of data.
UranosC1-ENcopyA_F1_FM.book Page 73 Friday, July 26, 2002 5:01 PM 3. Color Adjustment/Program Color Adjustment This function lets you alter up to three single colors by mixing them with adjacent colors in the color circle. Reference For types and examples of the image adjustment functions. ⇒ p.i “What You Can Do With This Machine ” Note ❒ You can set up to 3 colors from yellow, red, magenta, blue, cyan, or green. ❒ This function is only available in Full Color mode.
UranosC1-ENcopyA_F1_FM.book Page 74 Friday, July 26, 2002 5:01 PM Color Adjustment/Program Color Balance Adjusts the overall color tone when the overall copy is reddish or bluish. Reference For types and examples of the image adjustment functions. ⇒ p.i “What You Can Do With This Machine ” 3 A Press the {Adjust/Program Color} } key. B Make sure that [Color Balance] is selected. C Adjust by pressing [Lighter] or [Darker].
UranosC1-ENcopyA_F1_FM.book Page 75 Friday, July 26, 2002 5:01 PM Color Balance Changing the registered contents A Press the {Adjust/Program Color} } key. B Confirm that [Color Balance] is selected, and press [Program Color Balance]. C Select the program number (1–3) to be changed. The programmed color balance appears. D Change the registered contents. E After the programmed contents are changed, press [Program Color Balance].
UranosC1-ENcopyA_F1_FM.book Page 76 Friday, July 26, 2002 5:01 PM Color Adjustment/Program Image Adjustment Reference For types and examples of the image adjustment functions. ⇒ p.i “What You Can Do With This Machine ” The followings are types of image adjustments you can make. 3 ❖ Sharp/Soft For adjusting the outline of an image. ❖ Contrast For adjusting the shades of an image. ❖ Background Density For adjusting the background density of an image.
UranosC1-ENcopyA_F1_FM.book Page 77 Friday, July 26, 2002 5:01 PM Image Adjustment ❒ Adjustments should be made darker when darkening the color of markers or highlighters. However, as the color of highlighters is difficult to reproduce, the copy might not come out depending on the color or a different color might be copied. B Press [OK]. Adjusting the U.C.R. A Adjust by pressing [Lighter] or [Darker]. B Press [OK].
UranosC1-ENcopyA_F1_FM.book Page 78 Friday, July 26, 2002 5:01 PM Color Adjustment/Program Note ❒ The test pattern will not be read if it is set in the optional document feeder (ADF). ❒ Set the test pattern in the following way: 3 ❒ When the optional document feeder (ADF) is installed, make sure to set the test pattern on the exposure glass, and then 2 or 3 white sheets, same size as the test pattern, above the test pattern.
UranosC1-ENcopyA_F1_FM.book Page 79 Friday, July 26, 2002 5:01 PM User Color User Color You can register colors made by adjusting the density of yellow, magenta, cyan, and black. You can also give a name to the colors you register, and print out registered colors. Reference For types and examples of the image adjustment functions ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 80 Friday, July 26, 2002 5:01 PM Color Adjustment/Program Selecting from registered colors When renaming a color A Press [User Color]. B Select from the colors. A Press [Change Name]. B Enter the name of the color (up to 16 characters), and then press [OK]. registered E Specify the color density. Using [n n] [o o] A Specify the density in percentages (%) using [n n] or [o o].
UranosC1-ENcopyA_F1_FM.book Page 81 Friday, July 26, 2002 5:01 PM User Color Mixing Colors Manually with the Number Keys A Press the {Adjust/Program Color} } key. B Press [User Color]. C Select the number (1–15) that you want to store the user color in. Note ❒ The contents of the user color will change when selecting the number already displayed by the color name. Deleting User Colors Note ❒ You can not delete colors registered in the program or registered colors that are currently being used.
UranosC1-ENcopyA_F1_FM.book Page 82 Friday, July 26, 2002 5:01 PM Color Adjustment/Program Programs You can store the frequently used copy job settings in the machine memory and recall them for future use. B Press the {Program}} key. Storing a Program 3 Note ❒ You can store up to 10 programs. ❒ You can select the standard mode or program No. 10 as the mode to be set when modes are cleared or reset, or immediately after the operation switch is turned. ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 83 Friday, July 26, 2002 5:01 PM Programs F Press [OK]. When the settings are successfully stored, the m indicator goes on.The screen returns to the initial copy display for a while. Recalling a Program A Press the {Program}} key. B Press [Recall]. Changing a stored program A Check the program settings. Note ❒ When you want to check the contents of a program, recall the program. ⇒ p.83 “Recalling a Program” B Repeat steps A to D of “Storing a Program”.
UranosC1-ENcopyA_F1_FM.
UranosC1-ENcopyA_F1_FM.book Page 85 Friday, July 26, 2002 5:01 PM 4. Troubleshooting If Your Machine Does Not Operate as You Want When a Message is Displayed The following chart contains explanations for the common messages. If other messages appear, follow the instructions as they are displayed. Problem Cause Action Cannot detect original size. Improper original is placed. ⇒ p.9 “Sizes difficult to detect” Place a custom size original on the exposure glass. ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 86 Friday, July 26, 2002 5:01 PM Troubleshooting 4 86 Problem Cause Cannot copy. Original is being scanned by other functions. The Document Server func- To cancel the job in process, press tion is in use. [Exit], and then press the {Document Server} } key. Next, press the {Clear/Stop} } key. When the message ”[Stop] was pressed. Stop storing?” appears, press [Stop].
UranosC1-ENcopyA_F1_FM.book Page 87 Friday, July 26, 2002 5:01 PM If You Cannot Make Clear Copies If You Cannot Make Clear Copies Problem Cause Action Copies appear dirty. The image density is too dark. Adjust the copy density. ⇒ p.29 “Adjusting Copy Image Density” Auto Image Density is not selected. Adjust the auto density. ⇒ p.29 “Adjusting Copy Image Density” The reverse side of an orig- The image density is too inal image is copied. dark.
UranosC1-ENcopyA_F1_FM.book Page 88 Friday, July 26, 2002 5:01 PM Troubleshooting If You Cannot Make Copies as You Want This section explains causes and remedies when copy results are not as expected. Problem Cause Action Copies are not stapled. There are jammed staples in the stapler. Remove jammed staples. ⇒ General Settings Guide Note ❒ After removing jammed staples, staples might not be ejected the first few times you try to use the stapler. 4 Staples are wrongly positioned.
UranosC1-ENcopyA_F1_FM.book Page 89 Friday, July 26, 2002 5:01 PM If You Cannot Make Copies as You Want Problem Cause Action In Image Repeat mode, the original image is not copied repeatedly. You selected copy paper the same size as the originals, or you did not select the proper reproduction ratio. Select copy paper larger than the originals. The stamp position is wrong. The paper orientation is wrong. Check the paper orientation and stamp position.
UranosC1-ENcopyA_F1_FM.book Page 90 Friday, July 26, 2002 5:01 PM Troubleshooting When Memory is Full Note ❒ If you set "Memory Full Auto Scan Restart" of the User Tools ( ⇒ p.105 ) to "Yes", the memory overflow message will not be displayed, but make Connect Copy for the scanned originals automatically. Connect Copy continues scanning and copying until finishing the job. Note that copy sets will be printed out separately by scanning at this time. Message Cause Solution & Reference Memory is full.
UranosC1-ENcopyA_F1_FM.book Page 91 Friday, July 26, 2002 5:01 PM 5. User Tools (Copier/Document Server Features) User Tools Menu (Copier/Document Server Features) User Tools Item Names Default Settings General Features 1/5 ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 92 Friday, July 26, 2002 5:01 PM User Tools (Copier/Document Server Features) User Tools Item Names Default Settings General Features 3/5 ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 93 Friday, July 26, 2002 5:01 PM User Tools Menu (Copier/Document Server Features) User Tools Item Names Default Settings Reproduction Ratio 1/2 ⇒ p.
UranosC1-ENcopyA_F1_FM.book Page 94 Friday, July 26, 2002 5:01 PM User Tools (Copier/Document Server Features) User Tools Item Names Default Settings Edit 1/2 ⇒ p.101 “Edit 1/2” 5 Front Margin: Left/Right Metric version: Left 5mm Inch version: Left 0.2” Back Margin: Left/Right Metric version: Right 5mm Inch version: Right 0.
UranosC1-ENcopyA_F1_FM.book Page 95 Friday, July 26, 2002 5:01 PM User Tools Menu (Copier/Document Server Features) User Tools Item Names User Stamp Default Settings Program/Delete Stamp Stamp Position : 1~4 Metric version • Position: Top right • Top Margin: 24mm • Right Margin: 24mm Inch version • Position: Top right • Top Margin: 1.0" • Right Margin: 1.
UranosC1-ENcopyA_F1_FM.book Page 96 Friday, July 26, 2002 5:01 PM User Tools (Copier/Document Server Features) User Tools Item Names Page Numbering Default Settings Stamp Format P1, P2... Font Font 1 Size Auto Duplex Back Page Stamping Position Opposite Position Page Numbering in Combine Per original Stamp on Designated Slip Sheet No Stamp Position : Metric version • Position P1, 1/5, P.1, 1: Top right -1-, 1-1: Bottom center • Top/Bottom Margin P1, 1/5, P.
UranosC1-ENcopyA_F1_FM.book Page 97 Friday, July 26, 2002 5:01 PM Accessing the User Tools (Copier/Document Server Features) Accessing the User Tools (Copier/Document Server Features) This section is for the key operators in charge of this machine. You can change or set the machine's default settings. Note ❒ Be sure to exit from the User Tools after all the settings are finished. ❒ The selected key is highlighted.
UranosC1-ENcopyA_F1_FM.book Page 98 Friday, July 26, 2002 5:01 PM User Tools (Copier/Document Server Features) General Features 1/5 ❖ Auto Paper Select Priority As a default setting, Auto Paper Select is selected. You can cancel this setting. ⇒ p.31 “Selecting Copy Paper” ❖ Paper Display You can choose whether the available paper trays/sizes are shown on the initial display.
UranosC1-ENcopyA_F1_FM.book Page 99 Friday, July 26, 2002 5:01 PM Accessing the User Tools (Copier/Document Server Features) General Features 2/5 ❖ Duplex Mode Priority You can select the type of Duplex function effective when the machine is turned on, reset, or modes are cleared. ❖ Copy Orientation in Duplex Mode You can set the copy orientation when making two-sided copies. ❖ Original Orientation in Duplex Mode You can set the original orientation when making two-sided copies.
UranosC1-ENcopyA_F1_FM.book Page 100 Friday, July 26, 2002 5:01 PM User Tools (Copier/Document Server Features) General Features 5/5 ❖ Clear Bypass Mode Set this function to whether or not the settings of the Bypass Tray are cleared, when the machine is turned on, reset, or modes are cleared. ❖ Color Mode Priority You can select the priority of the color mode.
UranosC1-ENcopyA_F1_FM.book Page 101 Friday, July 26, 2002 5:01 PM Accessing the User Tools (Copier/Document Server Features) Edit 1/2 Edit 2/2 ❖ Front Margin: Left/Right You can specify left and right margins on the front side of copies in Margin Adjust mode. ❖ Front Cover Copy in Combine You can specify whether to make a combined copy on the front cover sheet when you select Front cover copy mode.
UranosC1-ENcopyA_F1_FM.book Page 102 Friday, July 26, 2002 5:01 PM User Tools (Copier/Document Server Features) ❖ Image Repeat Separation Line You can select a separation line in Image Repeat mode from None, Solid, Broken A, Broken B or Crop Marks. • None 5 102 ❖ Double Copies Separation Line You can select a separation line in Double Copy mode from None, Solid, Broken A, Broken B or Crop Marks.
UranosC1-ENcopyA_F1_FM.book Page 103 Friday, July 26, 2002 5:01 PM Accessing the User Tools (Copier/Document Server Features) ❖ Separation Line in Combine You can select a separation line in Combine mode from None, Solid, Broken A, Broken B or Crop Marks. • None • Solid • Broken A • Broken B • Crop Marks Note ❒ Separation lines cannot be specified when [None] is selected.
UranosC1-ENcopyA_F1_FM.book Page 104 Friday, July 26, 2002 5:01 PM User Tools (Copier/Document Server Features) User Stamp 1/2-2/2 ❖ Program/Delete Stamp You can register/change/delete these designs as user stamps. Note ❒ You can register up to 4 custom stamps with your favorite designs. Reference For how to Program/Delete Stamp, see ⇒ p.62 “To program the user stamp” ❖ Stamp Position 1 - 4 You can set the position at which the stamp is printed. Press the arrow keys to adjust the position.
UranosC1-ENcopyA_F1_FM.book Page 105 Friday, July 26, 2002 5:01 PM Accessing the User Tools (Copier/Document Server Features) ❖ Page Numbering in Combine You can set how the pages are numbered when you use the Combine function and Page Numbering function together. ❖ Stamp on Designated Slip Sheet You can select whether to print the page number onto slip sheets when you use the Designate function set to "Copy" and Page Numbering function together. ❖ Stamp Position P1, P2... Stamp Position: 1/5, 2/5...
UranosC1-ENcopyA_F1_FM.book Page 106 Friday, July 26, 2002 5:01 PM User Tools (Copier/Document Server Features) Note ❒ If you select [No] : • When the memory becomes full, the machine stops operation allowing you to remove the copy pages delivered on the output tray. ❒ If you select [Yes] : • You can leave the machine unattended to make all the copies, but the resulting sorted pages will not be sequential.
UranosC1-ENcopyA_F1_FM.book Page 107 Friday, July 26, 2002 5:01 PM 6. Specifications Combination Chart The combination chart given below shows which modes can be used together. When you read the chart, see the following table. ❍ means that these modes can be used together. $ means that these modes cannot be used together. The second mode selected will be the mode you're working in. × means that these modes cannot be used together. The first mode selected will be the mode you're working in.
UranosC1-ENcopyA_F1_FM.book Page 108 Friday, July 26, 2002 5:01 PM Specifications Supplementary Informations ❖ Bypass Tray Copy • The following paper sizes can be selected as the standard sizes.
UranosC1-ENcopyA_F1_FM.
UranosC1-ENcopyA_F1_FM.book Page 110 Friday, July 26, 2002 5:01 PM Specifications Paper Size and Direction ❖ Sort, Rotate Sort, Stack Paper sizes and orientations that can be used in the Sort function are as follows.
UranosC1-ENcopyA_F1_FM.book Page 111 Friday, July 26, 2002 5:01 PM 500-Sheet Finisher Supplementary Informations Paper Size and Direction Paper Capacity and Weight A4KL, B5KL *3 , A5K *3 , 81/2" × 11"KL, 51/2" × 81/2"K *3 , 71/4" × 101/2"KL *3 , 16KKL *3 500 sheets (80g/m2) (20 lb.) A3L, B4L, 11" × 17"L, 81/2" × 14"L, 8" × 13"L, 81/4" × 13"L, 81/2" × 13"L, 8KL 250 sheets (80g/m2) (20 lb.) Finisher proof tray 250 sheets (80g/m2) (20 lb.
UranosC1-ENcopyA_F1_FM.book Page 112 Friday, July 26, 2002 5:01 PM Specifications • When paper types is selected to [Thick Paper], [Thick: Dup.Back], [Plain: Dup.Back], [Label Paper], or [OHP] in the System Settings, stapling cannot be done. • 500-Sheet Finisher can staple papers of 64-128g/m2 (17-34lbs) in the paper weight. • 1000-Sheet Finisher can staple papers of 64-96g/m2 (17-24lbs) in the paper weight.
UranosC1-ENcopyA_F1_FM.book Page 113 Friday, July 26, 2002 5:01 PM Supplementary Informations • Label paper (adhesive labels) • OHP transparencies • Envelopes When an odd number of originals is set in the optional document feeder, the back of the last page of copied paper is blank. During copying, the image is shifted to allow for the binding margin. • When an odd number of originals is set in the optional document feeder, the back of the last page of copied paper is blank.
UranosC1-ENcopyA_F1_FM.book Page 114 Friday, July 26, 2002 5:01 PM Specifications ❖ Erase The width of the erased margin varies depending on the reproduction ratio. This function is available for the following paper sizes.
UranosC1-ENcopyA_F1_FM.book Page 115 Friday, July 26, 2002 5:01 PM Supplementary Informations ❖ Page Numbering When page numbering is used with Combine mode, page numbers are printed as follows.
UranosC1-ENcopyA_F1_FM.
UranosC1-ENcopyA_F1_FM.
UranosC1-ENcopyA_F1_FM.
UranosC1-ENcopyA_F1_FM.
UranosC1-ENcopyA_F1_FM.
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=128 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 5.120000 mm Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine.
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=128 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 5.
