Instruction manual

ManualsBrandsSavin ManualsAll in One PrinterC2410

WARNING

FAILURE TO CAREFULLY OBSERVE THE

FOLLOWING INSTRUCTIONS COULD

RESULT IN SEVERE EQUIPMENT DAMAGE.

735348S-001 Rev.

August 28, 2009

INSTRUCTIONS FOR INSTALLING

VENDAPIN LLC VENDING PRODUCTS TO RICOH, SAVIN, GESTETNER AND LANIER COPIERS

Note for 2-price capability, the Coin Box or Card Reader must be set to “Steering Mode”. For a full explanation

see STEERING SIGNAL MODE in the user manuals.

NOTE: Optional Counter Interface Unit for Multi pricing must already be installed.

for Ricoh its part # EDP code 413012.

1. Make sure the Ricoh/Savin/Gestetner/Lanier copier is functioning properly before connecting to the

VENDAPIN, LLC vending unit.

2. Consult with your Ricoh/Savin/Gestetner/Lanier technical support representative on instructions for

configuring your copier with an external vending device.

3. Turn off the Copier’s main power and unplug from the AC receptacle.

4. Make sure the VENDAPIN LLC vending unit is unplugged from the AC receptacle.

5. Locate the 609348R machine harness that came with the VENDAPIN, LLC vending unit.

6. Open the VENDAPIN, LLC vending unit to access the Raptor II VMC controller board inside. See

Figure 1.

Figure 1

Summary of content (6 pages)

PAGE 1
735348S-001 Rev. August 28, 2009 WARNING FAILURE TO CAREFULLY OBSERVE THE FOLLOWING INSTRUCTIONS COULD RESULT IN SEVERE EQUIPMENT DAMAGE. INSTRUCTIONS FOR INSTALLING VENDAPIN LLC VENDING PRODUCTS TO RICOH, SAVIN, GESTETNER AND LANIER COPIERS Note for 2-price capability, the Coin Box or Card Reader must be set to “Steering Mode”. For a full explanation see STEERING SIGNAL MODE in the user manuals. NOTE: Optional Counter Interface Unit for Multi pricing must already be installed.
PAGE 2
735348S-001 Rev. August 28, 2009 WARNING FAILURE TO CAREFULLY OBSERVE THE FOLLOWING INSTRUCTIONS COULD RESULT IN SEVERE EQUIPMENT DAMAGE. 7. Plug the VENDAPIN, LLC machine harness mini-Dsub 15 position connector to J2 on the Raptor II VMC controller. Ensure the mounting screws are tight. See Figure 2. Figure 2 8. Route the VENDAPIN, LLC machine harness out of the bottom of the enclosure as shown in the following photos. Use the supplied strain relief to secure the harness in the exit hole.
PAGE 3
735348S-001 Rev. August 28, 2009 WARNING FAILURE TO CAREFULLY OBSERVE THE FOLLOWING INSTRUCTIONS COULD RESULT IN SEVERE EQUIPMENT DAMAGE. Figure 3 Figure 4 9. Connect the 20 position black connector into CN4 on the I/O Board of the copier. See Figure 5. Note: The connector number may vary by manufacturer.
PAGE 4
735348S-001 Rev. August 28, 2009 WARNING FAILURE TO CAREFULLY OBSERVE THE FOLLOWING INSTRUCTIONS COULD RESULT IN SEVERE EQUIPMENT DAMAGE. Figure 5 . 10. Make sure machine harness wires are away from all moving parts. 11. The installation is now complete. It is recommended that the system be tested prior to replacing any of the copier covers. Refer to the Operator/Installation Instruction Manual for proper set up and test procedures.
PAGE 5
TABLE 1: Ricoh, Savin, Lanier, Gestetner 6-Price Machine Harness (609348-001) For 5596 Series Price 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 BK/W or Color BK/W BK/W BK/W N/A N/A N/A N/A N/A Color Color Color N/A N/A N/A N/A N/A Size (LT) 11”x 8 1/2” (LG) 8 1/2”x 14” (DLT) 11”x 17” N/A N/A N/A N/A N/A (LT) 11”x 8 1/2” (LG) 8 1/2”x 14” (DLT) 11”x 17” N/A N/A N/A N/A N/A TIMING HELP Please refer to your VENDAPIN, LLC user manual for the proper procedure to change the timing settings described below.
PAGE 6
Knowledge Base: Problem Multiple debits occur on a single vend Free copies being dispensed No debits occur No debit on last vend Paper jams (first copy) Paper jams (one copy selected, tries to make another copy) • Cause Sense time too short • • Blind time too short • • Sense time too long • • • • • • Bypass keyswitch on Reset delay too long Sense time too long Blind time too long Reset delay time too short Reset delay time too long Leading edge not selected Eject delay time too short Eject dela