DolphinGB-Copy-F_V4_FM.book Page 71 Monday, June 11, 2001 5:02 PM Shift Shift Moves (shifts) the copy image up, down, left, or right to create a margin. • [← ←] key (Left): Shifts the image towards the left of the original. • [→ →] key (Right): Shifts the image towards the right of the original. You can shift the image from 0 to 200mm in 1mm steps (0 to 7.8" in 0.1" steps). The default setting is 20mm, 2.0". You can change this setting. See p.
DolphinGB-Copy-F_V4_FM.book Page 72 Monday, June 11, 2001 5:02 PM Copying Creating a top or bottom margin A Press the [↑ ↑] or [↓ ↓] keys to set the length of the shift amount. 2 Creating a left or right margin A Press the [← ←] or [→ →] keys to set the length of the shift amount. C Press the [OK] key.
DolphinGB-Copy-F_V4_FM.book Page 73 Monday, June 11, 2001 5:02 PM Border Erase Border Erase Erases the rim area of the original image. Setting border erase to same width A Press the [Same Width] key. B Press the [-] or [+] keys to set the Border Erase width, and then press the [OK] key. 2 ZEDX080E Preparation The default border erase setting is 10mm, 0.4". You can change this setting. See p.133 “Border Erase Width Priority” A Press the [Shift/Erase] key.
DolphinGB-Copy-F_V4_FM.book Page 74 Monday, June 11, 2001 5:02 PM Copying B Press the [Top], [Bottom], [Left] and [Right] keys to select the erase rim area, and set the Border Erase width using the [-] or [+] keys. Then press the [OK] key. 2 Limitation ❒ When using the Border Erase function with other functions, see p.102 “Chart of Scan Sizes for Each Function”.
DolphinGB-Copy-F_V4_FM.book Page 75 Monday, June 11, 2001 5:02 PM Delete Inside Delete Inside Copies the original while erasing parts inside a specified area. A Press the [Shift/Erase] key. Delete Inside 2 ZEDX010E B Press the [Delete Inside] key. Limitation ❒ If the original is larger than A1, you can only erase one area (Metric version only). ❒ If the original is larger than C, you can only erase one area (Inch version only).
DolphinGB-Copy-F_V4_FM.book Page 76 Monday, June 11, 2001 5:02 PM Copying D To specify several areas, specify areas 1 – 5 in the same way. 2 E Press the [OK] key.
DolphinGB-Copy-F_V4_FM.book Page 77 Monday, June 11, 2001 5:02 PM Delete Outside Delete Outside Copies the original while erasing parts outside a specified area. A Press the [Shift/Erase] key. Delete Outside 2 ZEDX020E B Press the [Delete Outside] key. Limitation ❒ If the original is larger than A1, you can only specify one area (Metric version only). ❒ If the original is larger than C, you can only erase one area (Inch version only).
DolphinGB-Copy-F_V4_FM.book Page 78 Monday, June 11, 2001 5:02 PM Copying Double Copies One original image is copied twice on to one copy as shown in the illustration. B Press the [Double Copies ] key. 2 C Press the [OK] key. ZEDG170E Limitation ❒ You can copy an image up to A2 (C) in size with the Double Copies function K. You can use a paper size up to A1 (D) L. Note ❒ You can erase the separation line between the two images. The default setting is Separation Line. See p.
DolphinGB-Copy-F_V4_FM.book Page 79 Monday, June 11, 2001 5:02 PM Image Repeat Image Repeat The original image is copied repeatedly. ❒ When using Image Repeat with the Shift function, the composite image is repeated. ❒ When using Image Repeat with the Image Overlay function, the composite image is repeated. 2 A Select the paper. B Press the [Edit Image] key. ZEDG180E Preparation The number of repeated images depends on the original size, copy paper size, and reproduction ratio.
DolphinGB-Copy-F_V4_FM.book Page 80 Monday, June 11, 2001 5:02 PM Copying Positive/Negative Black and white areas of the original are reversed. B Press the [Positive/Negative] key. 2 ZEDG150E Limitation ❒ You can use Positive/Negative for copies with sizes up to A0(E). Note ❒ When making continuous copies, the image density may deteriorate. See p.106 “If You Cannot Make Clear Copies” A Press the [Edit Image] key. 80 C Press the [OK] key.
DolphinGB-Copy-F_V4_FM.book Page 81 Monday, June 11, 2001 5:02 PM Mirror Image Mirror Image The image is mirrored along the left/ right axis, so that it appears as it would when viewed in a mirror. 2 ZEDG160E A Press the [Edit Image] key. B Press the [Mirror Image] key. C Press the [OK] key.
DolphinGB-Copy-F_V4_FM.book Page 82 Monday, June 11, 2001 5:02 PM Copying Image Overlay Two originals are combined on one copy. B Press the [Image Overlay] key. 2 First Original Second Original Copy Third Original Fourth Original Copy ZEDG280E Limitation ❒ For details on the combinations for background original and original for the composite image, see p.83 “Image Overlay Limitations”. ❒ You cannot shift the position of the first or second original after the composite image has been created.
DolphinGB-Copy-F_V4_FM.book Page 83 Monday, June 11, 2001 5:02 PM Image Overlay Image Overlay Limitations Limitation ❒ When using Image Overlay, you should use a second original that is larger than the first original. Because the background image (image of the first original) will be cut if Preset Cut is selected, and if the second original is smaller than the first original.
DolphinGB-Copy-F_V4_FM.book Page 84 Monday, June 11, 2001 5:02 PM Copying Format Overlay The optional HDD are required to use this function. Two images (original + format) are combined on one copy using stored image (user format) or first original. You can store the format original and recall it for next use. 2 First Original or User Format Second Original Copy Third Original Copy Scanning the format original (background original) A Press the [First Original] key. B Press the [OK] key.
DolphinGB-Copy-F_V4_FM.book Page 85 Monday, June 11, 2001 5:02 PM Format Overlay Storing a format overlay beforehand Note ❒ To use User Format Overlay, you need to use Program /Delete, Overlay Format. See p.85 “Program/Delete, Overlay Format” A Select a stored format original. ❒ You cannot use Format Overlay with the following functions. • Image Overlay • Sort • Rotate Sort ❒ The maximum size for the paper size is A1 (D).
DolphinGB-Copy-F_V4_FM.book Page 86 Monday, June 11, 2001 5:02 PM Copying Overwriting a stored format A Select the format number for the format you want to overwrite. B Press the [Program] key. 2 C Press the [OK] key. Note ❒ To cancel the deletion, press the [No] key. Important ❒ You cannot restore a format that has been deleted. E Press the {User Tools/Counter} key. The machine exits Program/Delete and is ready to copy. C Press the [OK] key. D Press the [OK] key.
DolphinGB-Copy-F_V4_FM.book Page 87 Monday, June 11, 2001 5:02 PM Background Numbering Background Numbering The optional stamp board and HDD are required to use this function. This function produces copies which have been stamped by the numbering user stamp. ZEDG190E Preparation You can set the start number from 1 to 999. Note ❒ You can change the density of the background numbers. See p.137 “Background Numbering Format” ❒ You can change the size of the background numbers. See p.
DolphinGB-Copy-F_V4_FM.book Page 88 Monday, June 11, 2001 5:02 PM Copying User Stamp Repeat The optional stamp board and HDD are required to use this function. Prints a stored user stamp of letters or symbols on the whole area of the paper. 2 Reference For details on deleting a User Stamp, see "Program/Delete, User Stamp". See p.92 “Program/Delete, User Stamp” A Press the [Stamp] key. ZEDG270E Preparation You must store a User Stamp before using this function. See p.
DolphinGB-Copy-F_V4_FM.book Page 89 Monday, June 11, 2001 5:02 PM Preset Stamp Preset Stamp The optional stamp board and HDD are required to use this function. Prints a user stamp that has already been stored. ❖ Place your originals, and then specify the user stamp position and direction. 2 Feed Direction Horizon ZEDG200E Preparation The stamp types are as follows. Vertical Feed Direction Horizon You can change the position and direction of the stamp.
DolphinGB-Copy-F_V4_FM.book Page 90 Monday, June 11, 2001 5:02 PM Copying A Press the [Stamp] key. D Select the print direction ([Horiz.] or [Vert.] keys), and print position for the stamp. 2 B Press the [Preset Stamp] key. Changing the size and density/ setting print page A Press the [Other Settings] key. C Select the stamp type. B Sets the Size, Density and Pagination. Note ❒ You can change the priority of the selected stamp. See p.134 “Preset Stamp Priority” E Press the [OK] key.
DolphinGB-Copy-F_V4_FM.book Page 91 Monday, June 11, 2001 5:02 PM User Stamp User Stamp The optional stamp board and HDD are required to use this function. You can store frequently used characters or symbols, and then use them as a stamp. ❖ Place the originals and then specify the stamp position and direction. 2 Feed Direction Horizon ZEDG220E Vertical Preparation You must store a user stamp. See p . 9 2 “ P ro g ra m / D e le t e , U s e r Stamp” You can store up to four types of user stamps.
DolphinGB-Copy-F_V4_FM.book Page 92 Monday, June 11, 2001 5:02 PM Copying A Press the [Stamp] key. B Set the Density and Pagination. 2 B Press the [User Stamp] key. E Press the [OK] key. Reference For details on how to set the originals, see p.31 “Setting Originals”. Program/Delete, User Stamp C Select the number for the user stamp. Preparation If the stamp printed on the original is bright red or red, it may not be scanned clearly.
DolphinGB-Copy-F_V4_FM.book Page 93 Monday, June 11, 2001 5:02 PM User Stamp E Press the [Program/Delete, User Stamp] key. ❒ You can specify the print conditions for stored stamps. See p.138 “User Stamp Format” Overwriting a stored user stamp A Select the number for the stamp you want to overwrite, and then press the [OK] key. Storing 2 A Select the number you want to use to store the stamp, and then press the [OK] key. B Press the [Program] key. B Place your originals. C Press the [OK] key.
DolphinGB-Copy-F_V4_FM.book Page 94 Monday, June 11, 2001 5:02 PM Copying Deleting A Select the number of the stamp you want to delete, and then press the [OK] key. B Press the [Delete] key. 2 C Press the [OK] key. "Are you sure you want to delete this programmed stamp?" is displayed on the screen. D Press the [OK] key. Note ❒ To cancel the deletion, press the [No] key. Important ❒ You cannot use a user stamp which has been deleted. F Press the {User Tools/Counter} key.
DolphinGB-Copy-F_V4_FM.book Page 95 Monday, June 11, 2001 5:02 PM Date Stamp Date Stamp The optional stamp board and HDD are required to use this function. 2002.2.12 ZEDG250E Preparation Specify the print position (Top left/Top centre/Top right/Bottom left/Bottom centre/Bottom right) and print direction (Horizontal/ Vertical). Note ❒ You can change the date format of the date stamp. See p.136 “Date Stamp Format Priority” ❒ You can also set and change the other date stamp conditions. See p.
DolphinGB-Copy-F_V4_FM.book Page 96 Monday, June 11, 2001 5:02 PM Copying C Select the date format for the date stamp. 2 D Select the print direction ([Horiz.] or [Vert.] keys) and the print position. Selecting pagination A Press the [Pagination] key. B Select the [All Pages] or [First Page Only] key, and then press the [OK] key. E Press the [OK] key.
DolphinGB-Copy-F_V4_FM.book Page 97 Monday, June 11, 2001 5:02 PM Page Numbering Page Numbering The optional stamp board and HDD are required to use this function. Use this function to print page numbers on your copies. There are five types of Page Numbering. AB AB R R A Press the [Stamp] key. 2 -1- -2- -3- B Press the [Page Numbering] key. ZEDG300E There are five types of Page Numbering. • 1, 2,… • -1-, -2-,… • P1, P2,… • P.1, P.2,… • 1/5, 2/5,… C Select the page print format.
DolphinGB-Copy-F_V4_FM.book Page 98 Monday, June 11, 2001 5:02 PM Copying D Select the print direction ([Horiz.] or [Vert.] keys) and print position. Selecting first page to Print/Last Page to print and start numbering from A Press the [Pagination] key. B To change the first/last page, and starting page, press the corresponding key, and then enter the value with the number keys. Then press the [#] key. 2 If [1/5,2/5…] are selected If you select [1/5,2/5…] the screen for setting fractions is displayed.
DolphinGB-Copy-F_V4_FM.book Page 99 Monday, June 11, 2001 5:02 PM Combination Chart Combination Chart The combination chart given below shows which modes can be used together.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.book Page 101 Monday, June 11, 2001 5:02 PM Combination Chart ❖ Symbols used in the chart Blank means that these modes can be used together. F means that these modes cannot be used together. The mode you select will be the mode you're working in. B means that these modes cannot be used together. The mode you select will be the mode you're working in. S means that these modes cannot be used together.
DolphinGB-Copy-F_V4_FM.book Page 102 Monday, June 11, 2001 5:02 PM Copying Chart of Scan Sizes for Each Function The following chart shows the scan size limitations for Shift, Margin Adjustment, Edit Image, and Print functions. 2 Functions Standard Optional HDD installed Shift A0(E) less than 6m (236") Margin Adjustment A0(E) less than 6m Image Image Overlay Overlay Format Overlay A1(D) A0 (E) — A0 (E) Erase A1 or smaller, 5 location. A1 or smaller, 5 location.
Dol_Chapter-3 Page 103 Thursday, July 19, 2001 3:16 PM 3. Troubleshooting If Your Machine Does Not Operate As You Want Error Messages Machine's Condition Problem/Cause Action Please Wait. Displayed when the main power is turned on, when the paper type (plain paper/ translucent paper/film) is changed, the toner is replaced, or other situations when the machine is getting ready. Wait for the machine to warmup.
DolphinGB-Copy-F_V4_FM.book Page 104 Monday, June 11, 2001 5:02 PM Troubleshooting Machine's Condition Problem/Cause Action Check paper size. The paper size is different to the size of the original. • Set the suitable paper, or change paper roll selecting. • Reset the function settings, and then try again. Rotate Sort mode is not available with the current settings. The scanned original is too big to rotate. You cannot use rotate sort with A0 (E) originals.
DolphinGB-Copy-F_V4_FM.book Page 105 Monday, June 11, 2001 5:02 PM If Your Machine Does Not Operate As You Want Screen Problem Cause Action The screen is off. The screen contrast knob is turned to the dark position. Turn the screen contrast knob until you can see the screen. The machine is in Energy Sav- Press the {Clear Modes/Energy er mode. Saver} key to cancel Energy Saver mode. Cannot select the functions on the screen. The power does not come on. The operation switch is turned off.
DolphinGB-Copy-F_V4_FM.book Page 106 Monday, June 11, 2001 5:02 PM Troubleshooting If You Cannot Make Clear Copies Problem Cause Black or white streaks appear on the copy. The image density is too dark. Adjust the image density. See p.41 “Adjusting Copy Image Density” 3 Action The exposure glass or feed roller is dirty. Clean the exposure glass or feed roller. See p.147 “Maintaining Your Machine” The original is dusty. Clean the original and try copying again.
DolphinGB-Copy-F_V4_FM.book Page 107 Monday, June 11, 2001 5:02 PM If You Cannot Make Clear Copies Problem Cause Action The toner fusing is poor. The toner fusing temperature is too low. Adjust the fusing setting for the paper. See "Fusing Adjustment: Paper Tray" in the System Settings manual. The copy paper is too thick. A moire pattern is produced on copies. Your original has dot pattern image or many lines. Change the direction of the original. This may prevent the moire pattern.
DolphinGB-Copy-F_V4_FM.book Page 108 Monday, June 11, 2001 5:02 PM Troubleshooting If You Cannot Make Copies As You Want Problem Cause Action Misfeeds occur frequently. There are folds or wrinkles in the paper. Remove the folds or wrinkles from the roll paper. Jammed paper or torn paper is Remove the paper, as approinside the machine. priate. See p.116 “xClearing Misfeeds” The paper is curled. 3 Images are cropped when us- The Border Erase setting is to ing the Border Erase function. too big.
DolphinGB-Copy-F_V4_FM.book Page 109 Monday, June 11, 2001 5:02 PM If You Cannot Make Copies As You Want Problem Cause Action Wrinkles appear in the copy. The paper is damp. Replace the paper with new paper. Cut the paper to 1000mm (40") just before copying. The paper is damp. See p.12 “Anti-humidity Heater Switch” Turn on the anti-humidity heater. See p.12 “Anti-humidity Heater Switch” The copies are slanted. The original is not straight.
DolphinGB-Copy-F_V4_FM.book Page 110 Monday, June 11, 2001 5:02 PM Troubleshooting Changing The Roll Paper Size Change the size guides on the left and right of the roll paper holder when you load different sized paper rolls. Important ❒ Always follow the instructions below when adjusting the roll paper holder. Do not force the roll paper holder by pulling or sliding it strongly. This could damage the holder.
DolphinGB-Copy-F_V4_FM.book Page 111 Monday, June 11, 2001 5:02 PM Changing The Roll Paper Size Setting the Roll Paper Holder 3 Reference Refer to the procedure for loading paper. See p.112 “CLoading Roll Paper”.
DolphinGB-Copy-F_V4_FM.book Page 112 Monday, June 11, 2001 5:02 PM Troubleshooting CLoading Roll Paper R CAUTION: • Be careful when replacing the roll paper or removing misfed paper by following the operating instructions properly. Otherwise, an injury may result from the paper cutter inside. Important ❒ When removing paper rolls, lift the roll holders on either side of paper roll before removing it. Do not lift one side only. This could damage the machine.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.book Page 114 Monday, June 11, 2001 5:02 PM Troubleshooting DAdding Toner R WARNING: • Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations for plastics. R CAUTION: • Keep toner (used or unused) and toner containers out of reach of children.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.book Page 116 Monday, June 11, 2001 5:02 PM Troubleshooting xClearing Misfeeds Original Misfeeds R CAUTION: • The fusing section of this equipment might be very hot. You should be very careful that you don't touch this section when removing the misfed paper. Important ❒ If the originals are fed at a slant or become jammed, press the {Scanner Stop} key. ❒ Do not turn off the operation switch when removing jammed originals. If you turn the power off, your settings will be lost.
DolphinGB-Copy-F_V4_FM.book Page 117 Monday, June 11, 2001 5:02 PM xClearing Misfeeds Paper Misfeeds R CAUTION: • The fusing section of this equipment might be very hot. You should be very careful that you don't touch this section when removing the misfed paper. R CAUTION: • Be careful when replacing the roll paper or removing misfed paper by following the operating instructions properly. Otherwise, an injury may result from the paper cutter inside.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.book Page 121 Monday, June 11, 2001 5:02 PM xClearing Misfeeds Copy output (rear) (C) Even if C is displayed, check the front area first and clear any paper jams there. If you still cannot clear the paper jam, use the following procedure. Important ❒ When clearing the paper, be careful of the auxiliary guide and other protrusions. 3 R CAUTION: • The fusing section of this equipment might be very hot.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.book Page 123 Monday, June 11, 2001 5:02 PM 4. User Tools (Copier Features) Accessing The User Tools (Copier Features) This section is for the key operation in charge of this machine. You can change or set the machine's default settings. Preparation Any changes you make with the user tools remain in effect even if the main power switch or operation switch is turned off, or the {Clear Modes/Energy Saver} key is pressed.
DolphinGB-Copy-F_V4_FM.book Page 124 Monday, June 11, 2001 5:02 PM User Tools (Copier Features) Exiting from User Tools A Press the {User Tools/Counter} key. The machine exits User Tools mode and is ready for copying. Note ❒ You can exit from the User Tools by pressing the [Exit] or the {Clear Modes/Energy Saver} key.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.book Page 126 Monday, June 11, 2001 5:02 PM User Tools (Copier Features) Settings You Can Change with the User Tools For details about how to display the settings, see p.123 “Accessing The User Tools (Copier Features)” General Features 1/2 ❖ Initial Mode Set Specifies the settings to appear in the Copy Initial Display screen after the machine is turned on, after Auto Reset, or after the {Clear Modes/Energy Saver} key has been pressed.
DolphinGB-Copy-F_V4_FM.book Page 127 Monday, June 11, 2001 5:02 PM Settings You Can Change with the User Tools ❖ Auto Image Density Priority Specifies whether Auto Image Density should be used after the machine is turned on, after Auto Reset, or after the {Clear Modes/Energy Saver} key has been pressed, or not. See p.41 “Adjusting Copy Image Density” • On • Off Note ❒ Default: On ❖ Density Priority Specified one of seven density levels as the image density.
DolphinGB-Copy-F_V4_FM.book Page 128 Monday, June 11, 2001 5:02 PM User Tools (Copier Features) ❖ Print Start Trigger Specifies whether all the originals should be scanned first, or not. To scan the originals first and then copy when the {Start} key is pressed, press the [Press Start Key] key, To start copying automatically after the originals have been scanned, press the [Set Original] key.
DolphinGB-Copy-F_V4_FM.book Page 129 Monday, June 11, 2001 5:02 PM Settings You Can Change with the User Tools ❖ Noise Reduction Specifies the noise (small specks of dirt or dust on the image) reduction level for each of the original types (Text, Text/Photo, Pale, Special Original.) If you select [Off], small scratches and specks on the original will not be removed. • Off • Low • Medium • High Note ❒ Default: Off ❖ Original Mode Quality Level Adjusts the finish for each original type.
DolphinGB-Copy-F_V4_FM.book Page 130 Monday, June 11, 2001 5:02 PM User Tools (Copier Features) ❖ Sample Copy Priority Specifies the default dimensions to be used for the Sample Copy function. See p.57 “Sample Copy” Note ❒ Default: 0 ❒ The value can be set from 0 to 250 mm (9"). ❖ Partial Copy Priority Specifies the default dimensions to be used for the start point (Y1) and end point (Y2) in the Partial Copy function. See p.58 “Partial Copy” 4 Note ❒ Default: • Y1: 0 (0.0") • Y2: 210 mm (8.
DolphinGB-Copy-F_V4_FM.book Page 131 Monday, June 11, 2001 5:02 PM Settings You Can Change with the User Tools Reproduction Ratio ❖ User Reproduction Ratio You can store up to three reproduction ratios, in addition to those in the Preset Ratio function. Enter the desired reproduction ratio with the number keys. Note ❒ Default: 100 % ❒ Use the {·} key to enter a decimal point. • 25.0% – 400.
DolphinGB-Copy-F_V4_FM.book Page 132 Monday, June 11, 2001 5:02 PM User Tools (Copier Features) ❖ Shortcut Reduce/Enlarge You can specify a frequently used reproduction ratio to appear on the basic screen. Note ❒ Default: • Metric version: 71% • Inch version (Engineering): 65% • Inch version (Architecture): 67% ❖ User Auto Reduce/Enlarge Specifies the original and copy sizes to be displayed when the [User Auto R/E] key is pressed. See p.
DolphinGB-Copy-F_V4_FM.book Page 133 Monday, June 11, 2001 5:02 PM Settings You Can Change with the User Tools Adjust Image ❖ Margin Adjustment Priority Specifies the default setting for the size of the margin. You can set the size for the top and bottom margin. See p.69 “Margin Adjustment” Note ❒ Default: • Metric version: 20 mm • Inch version: 0.8" ❖ Shift Image Area Priority Specifies the default setting for the Shift function. Use the arrow keys to set the shift direction and distance. See p.
DolphinGB-Copy-F_V4_FM.book Page 134 Monday, June 11, 2001 5:02 PM User Tools (Copier Features) ❖ Double Copies Separation Line Specifies whether to use a separation line, or not, for the Double Copies function. See p.78 “Double Copies” The separation line will be a dotted line. • None • Separation Line Note ❒ Default: Separation Line ❖ Program/Delete, Overlay Format Stores a format image (background image) for use with the Format Overlay function. You can store up to four formats. See p.
DolphinGB-Copy-F_V4_FM.book Page 135 Monday, June 11, 2001 5:02 PM Settings You Can Change with the User Tools ❖ Preset Stamp Format Priority Specifies the size, density, print direction and print position for each of the preset stamps (COPY, URGENT, PRIORITY, For Your Info., PRELIMINARY, For Internal Use Only, CONFIDENTIAL). You can make separate settings for both horizontal and vertical. See p.89 “Preset Stamp” • Size (1X, 2X, 4X, 8X) • Density (Normal, Light, Very Light) • Orientation (Horiz., Vert.
DolphinGB-Copy-F_V4_FM.book Page 136 Monday, June 11, 2001 5:02 PM User Tools (Copier Features) ❖ Date Stamp Format Priority Specifies the format and other conditions to be used for the Date Stamp function. See p.95 “Date Stamp” You can specify the format to be used for the date stamp and its orientation and position. • Date format • MM/DD/YYYY • DD/MM/YYYY • YYYY.MM.DD • MM.DD.YYYY • DD.MM.YYYY • DD.JUN.YYYY • Orientation • Position 4 Note ❒ Default: • Date Format: MM/DD/YYYY • Orientation: Horiz.
DolphinGB-Copy-F_V4_FM.book Page 137 Monday, June 11, 2001 5:02 PM Settings You Can Change with the User Tools ❖ Date Stamp Position Adjustment Specifies the print position on the copies for the date stamp. Enter the settings for stamp position with the [+][-] keys or the number keys. Note ❒ Default: • [From Left][From Right][From Top][From Bottom]: • Metric version: 24 mm • Inch version: 0.9" • [From Horiz. Center]: • Metric version: 0 mm • Inch version: 0.
DolphinGB-Copy-F_V4_FM.book Page 138 Monday, June 11, 2001 5:02 PM User Tools (Copier Features) Stamp 2/2 ❖ User Stamp Format Specifies the density, print direction and print size to be used for user stamps. You can set separate settings for horizontal and vertical. See p.
DolphinGB-Copy-F_V4_FM.book Page 139 Monday, June 11, 2001 5:02 PM Settings You Can Change with the User Tools ❖ Program/Delete, User Stamp You can store, change, or delete a design of your choice as a user stamp. You can store up to four user stamps. See p.91 “User Stamp”, p.92 “Program/Delete, User Stamp” ❖ Page Numbering Format Specifies the conditions to be used for the Page Numbering function. See p.
DolphinGB-Copy-F_V4_FM.book Page 140 Monday, June 11, 2001 5:02 PM User Tools (Copier Features) ❖ Page Numbering Position Adjustment Specifies the print position on the copies for the page number. Enter the settings for numbering position with the [+][-] keys or the number keys. Note ❒ Default: • [From Left][From Right][From Top][From Bottom]: • Metric version: 24 mm • Inch version: 0.9" • [From Horiz. Center] • Metric version: 0 mm • Inch version: 0.
DolphinGB-Copy-F_V4_FM.book Page 141 Monday, June 11, 2001 5:02 PM Settings You Can Change with the User Tools ❖ Program/Change/Delete, User Code You can register, change, or delete user codes (8 digits or less). You can store up to 100 user codes. Note ❒ Program • You can register user codes. Press the [Program] key, and then enter the user code with the number keys. ❒ Change • You can change user codes. Press the [Change] key after selecting the user code. ❒ Delete User Code • You can delete user codes.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.book Page 143 Monday, June 11, 2001 5:02 PM 5. Remarks Do's and Don'ts R CAUTION: • Unplug the power cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equipment. Important ❒ Only disconnect the power cord after checking that all copies are finished. • Do not touch areas on or around the fusing unit. These areas get hot.
DolphinGB-Copy-F_V4_FM.book Page 144 Monday, June 11, 2001 5:02 PM Remarks Where To Put Your Machine Machine Environment Your machine's location should be carefully chosen because environmental conditions greatly affect its performance. Optimum environmental conditions R CAUTION: • Keep the equipment away from humidity and dust. Otherwise a fire or an electric shock might occur. • Do not place the equipment on an unstable or tilted surface. If it topples over, it could cause injury.
DolphinGB-Copy-F_V4_FM.book Page 145 Monday, June 11, 2001 5:02 PM Where To Put Your Machine Access To Machine Place the machine near the power source, providing clearance as shown. Rear Left Right Front ZEDH400E Standard setting Front more than 100cm (40") Rear more than 70cm (28") Left more than 40cm (16") Right more than 45cm (18") Upper more than 45cm (18") 5 Note ❒ For the required space when options are installed, please contact your service representative.
DolphinGB-Copy-F_V4_FM.book Page 146 Monday, June 11, 2001 5:02 PM Remarks Power Connection R WARNING: • Only connect the machine to the power source described on the inside front cover of this manual. Connect the power cord directly into a wall outlet and do not use an extension cord. • Do not damage, break or make any modifications to the power cord. Do not place heavy objects on it. Do not pull it hard nor bend it more than necessary. These actions could cause an electric shock or fire.
DolphinGB-Copy-F_V4_FM.book Page 147 Monday, June 11, 2001 5:02 PM Maintaining Your Machine Maintaining Your Machine If the exposure glass or feed rollers are dirty, you will not be able to make clear copies. Clean them when they become dirty. Cleaning the exposure glass A Wipe the exposure glass with a soft, damp cloth. ❖ Cleaning the machine Wipe the machine with a soft dry cloth. If this does not remove the dirt, wipe the machine with a damp, tightly wrung, cloth.
DolphinGB-Copy-F_V4_FM.book Page 148 Monday, June 11, 2001 5:02 PM Remarks Cleaning the original feed guide A Wipe the original feed guides at the top and bottom with a soft, dry cloth. Cleaning The Paper Path Section Cleans toner powder that may have collected on the imaging area. A Lift the release levers on either side and open the paper path section. ZEDH240E Note ❒ If there is paper dust or threads inside, remove them. 5 B Close the original cover gently.
DolphinGB-Copy-F_V4_FM.book Page 149 Monday, June 11, 2001 5:02 PM 6.
DolphinGB-Copy-F_V4_FM.book Page 150 Monday, June 11, 2001 5:02 PM Specification ❖ Copying speed (full-size copying): 7 copies/minute (A1(D)L) (3.54 inch per second) ❖ Warm-up time: Less than 2 minutes (20°C) ❖ First copy time: • Metric version: When selected upper tray: 18 seconds (A1L), 25 seconds(A0K) • Inch version: When selected upper tray: 18.5 seconds (DL), 25.
DolphinGB-Copy-F_V4_FM.book Page 151 Monday, June 11, 2001 5:02 PM Mainframe • Inch version (Architecture): • Mainframe only Width Length 36" (30") Up to 48" 24" Up to 72" 18" Up to 96" 12" Up to 144" 9" Up to 192" When deleting a copy size: Up to 48" • Optional HDD installed 236" (any width) ❖ Non-reproduction area: • Metric version: • Top: 8mm • Bottom: 10mm • Left and Right 2 ± 2mm (less than 6mm on either side) • Inch version: • Top: 0.32" • Bottom: 0.39" • Left and Right 0.08" ± 0.
DolphinGB-Copy-F_V4_FM.book Page 152 Monday, June 11, 2001 5:02 PM Specification ❖ Original scanning pivot: Center ❖ Light source: LED ❖ Scanning resolution: 600dpi ❖ Scanning gradation: 256 values ❖ Printing gradation: 4 values ❖ Printing resolution: 600dpi ❖ Photo conductor type: OPC ❖ Development: Dry two-component magnetic brush development system 6 ❖ Fusing: Hot roller ❖ Power consumption: Metric version Inch version 1.6 kw 1.7 kw Ready (Anti-humidity heater 0.2 kw = OFF) 0.
DolphinGB-Copy-F_V4_FM.book Page 153 Monday, June 11, 2001 5:02 PM Options Options ❖ 2nd Roll Tray TypeA Adds the lower tray (paper roll 3). ❖ Roll Holder Unit TypeA When using different sizes of roll paper, use the roll holder to quickly change the paper rolls. ❖ Original Tray TypeG Attach this to the rear of the machine to store large quantities of originals.
DolphinGB-Copy-F_V4_FM.book Page 154 Monday, June 11, 2001 5:02 PM Specification Settings Record Sheet ❖ Program Record Sheet 6 Please make a copy of this sheet and use it to keep a record of your program settings.
DolphinGB-Copy-F_V4_FM.book Page 155 Monday, June 11, 2001 5:02 PM Settings Record Sheet ❖ Stored Format Record Sheet 6 Please make a copy of this sheet and use it to keep a record of your format settings.
DolphinGB-Copy-F_V4_FM.book Page 156 Monday, June 11, 2001 5:02 PM Specification ❖ User Stamp Record Sheet 6 Please make a copy of this sheet and use it to keep a record of your user stamps.
DolphinGB-Copy-F_V4_FM.book Page 157 Monday, June 11, 2001 5:02 PM Settings Record Sheet Magnification Ratio Chart ❖ Metric version (A series) Copy size Original size % A0 A1 A2 A3 A4 A0 100.0 70.7 50.0 35.4 25.0 A1 141.4 100.0 70.7 50.0 35.4 A2 200.0 141.4 100.0 70.7 50.0 A3 282.8 200.0 141.4 100.0 70.7 A4 400.0 282.8 200.0 141.4 100.0 D C B A ❖ Inch version (Engineering) Copy size Original size % E E 100.0 65.7 50.0 32.0 25.0 D 129.0 100.0 65.0 50.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.
DolphinGB-Copy-F_V4_FM.
