Quick Reference Guide
Table Of Contents
- Contents
- About the Savi SMR-650-216 Mobile Reader
- Hardware Components
- Savi SMR-650-216 and Intermec CK61G Mobile Computer
- Reader Communication
- Docking and Charging the Intermec CK61G
- 1. Connect the AC power cord to the power supply.
- 2. Connect the power supply to the dock charger and plug it into an AC power outlet.
- 3. Unzip the two zippers that connect the lower section of the soft case to the upper section.
- 4. Unsnap the snaps that connect the lower section of the soft case to the upper section.
- 5. When the lower section of the soft case is free, fold it up out of the way of the Savi Boot Adapter on the bottom of the Intermec CK61G. The Intermec CK61G ships with a plastic NI (Non-Incendive) protection cover on the boot adapter connector.
- 6. Before docking the Intermec CK61G Mobile Computer, use a screwdriver to remove the plastic NI cover and store it in the pouch.
- 7. Insert the Intermec CK61G into the dock charger by sliding the molded slots on either side of the boot adapter onto the corresponding guides on the dock charger.
- 8. Press down until you feel the adapter engage the dock charger.
- Optional Charging Method Without the Docking Station
- Resetting the SMR-650-216
- Using the Intermec CK61G Mobile Computer
- Optimizing the SMR-650 Reader Tag Collection Range
- Optimal CK61G Mobile Device Battery Life
- 1. Turn on the mobile device.
- 2. Tap Start > Settings.
- 3. Select the System tab.
- 4. Tap Backlight.
- • Check Turn off backlight if device is not used for and select 5 min.
- • Uncheck Dim backlight if device is not used for 15 seconds.
- • Check Turn on backlight when a button is pressed or the screen is tapped.
- • Under Brightness Level, move the pointer to the midway point or less.
- • Uncheck Turn off backlight if device is not used for.
- • Uncheck Dim backlight if device is not used for 15 seconds.
- • Check Turn on backlight when a button is pressed or the screen is tapped.
- • Under Brightness Level, move the pointer to the midway point or less.
- • Under On All Power, check Restore backlight state on resume.
- • Under Automatic Backlight Control, select Turn Off In Bright Light.
- • Under Battery Power > Device turns off after =, select 5 minutes.
- • Under Battery Power > Screen turns off after =, select 5 minutes.
- • Under External Power > Device turns off after =, select Disabled.
- • Under External Power > Screen turns off after =, select Disabled.
- Contacting Savi Support Services
- Specifications
9
you can store the plastic cover from the base of the Savi Boot Adapter in
the pouch.
W
ARNING: If the CK61G Mobile Computer is removed from the docking
station, you must reinstall the plastic cover when using the CK61G
Mobile Computer in an incendiary environment.
Reader Communication
The SMR-650 Reader has an ultra high frequency (UHF) transceiver and
low frequency (LF) transmitter that communicate with all Savi RFID tags
via the UHF and LF antennas. Your software determines if you use UHF
or LF commands.
UHF Mode
The UHF transmitter sends commands and write information to Savi
RFID tags. In UHF mode, the mobile reader supports single and
continuous collection modes.
When the mobile reader is in single UHF mode, you can only perform one
tag collection within a fixed radius. When the mobile reader is in
continuous UHF mode, you can perform multiple tag collections while
moving through a facility.
The yellow status LED is visible when the SMR-650 reader is receiving a
UHF signal and as an indication the tag ID and the information in the data
packets is being validated. When the yellow LED flashes, it indicates that
the mobile reader received a valid data packet. The yellow LED is only
functional when receiving UHF data and is not functional during UHF or
LF transmission. You can view the LED through a clear plastic window
in the soft case.