Quick Reference Guide
Table Of Contents
- Contents
- About the Savi SMR-650-216 Mobile Reader
- Hardware Components
- Savi SMR-650-216 and Intermec CK61G Mobile Computer
- Reader Communication
- Docking and Charging the Intermec CK61G
- 1. Connect the AC power cord to the power supply.
- 2. Connect the power supply to the dock charger and plug it into an AC power outlet.
- 3. Unzip the two zippers that connect the lower section of the soft case to the upper section.
- 4. Unsnap the snaps that connect the lower section of the soft case to the upper section.
- 5. When the lower section of the soft case is free, fold it up out of the way of the Savi Boot Adapter on the bottom of the Intermec CK61G. The Intermec CK61G ships with a plastic NI (Non-Incendive) protection cover on the boot adapter connector.
- 6. Before docking the Intermec CK61G Mobile Computer, use a screwdriver to remove the plastic NI cover and store it in the pouch.
- 7. Insert the Intermec CK61G into the dock charger by sliding the molded slots on either side of the boot adapter onto the corresponding guides on the dock charger.
- 8. Press down until you feel the adapter engage the dock charger.
- Optional Charging Method Without the Docking Station
- Resetting the SMR-650-216
- Using the Intermec CK61G Mobile Computer
- Optimizing the SMR-650 Reader Tag Collection Range
- Optimal CK61G Mobile Device Battery Life
- 1. Turn on the mobile device.
- 2. Tap Start > Settings.
- 3. Select the System tab.
- 4. Tap Backlight.
- • Check Turn off backlight if device is not used for and select 5 min.
- • Uncheck Dim backlight if device is not used for 15 seconds.
- • Check Turn on backlight when a button is pressed or the screen is tapped.
- • Under Brightness Level, move the pointer to the midway point or less.
- • Uncheck Turn off backlight if device is not used for.
- • Uncheck Dim backlight if device is not used for 15 seconds.
- • Check Turn on backlight when a button is pressed or the screen is tapped.
- • Under Brightness Level, move the pointer to the midway point or less.
- • Under On All Power, check Restore backlight state on resume.
- • Under Automatic Backlight Control, select Turn Off In Bright Light.
- • Under Battery Power > Device turns off after =, select 5 minutes.
- • Under Battery Power > Screen turns off after =, select 5 minutes.
- • Under External Power > Device turns off after =, select Disabled.
- • Under External Power > Screen turns off after =, select Disabled.
- Contacting Savi Support Services
- Specifications
23
Specifications
Specification Description
Model Number C K61-KIT-C-531
Active handheld RFID interrogator using the
Intermec CK61G and SMR-650
Physical Dimensions: CK61G: 8.7 in. (222 mm) x
3.5 in. (90 mm) x 2.1 in. (55 mm). SMR-650:
6.3 in. (158.8 mm) x 2.5 in. (63.5 mm) x 1 in.
(25 mm)
Weight: Total 31.2 ounces (885 g); CK61G:
24.8 ounces (704 g); SMR-650: 6.4 ounces
(181 g)
Display: Transflective TFT w/ LED backlight:
3.8 in. (97 mm) QVGA Color w/ touch panel
Keypad: 58-key w/ full alphanumeric keys
and LED backlighting
Environmental Temperature: -10°C to +50°C Operating;
-40°C to +60°C Storage
Humidity: 95%, Non-Condensing
Electrostatic Discharge: ±8kV Contact
Discharge; ±15kV Air Discharge
Drop Survival: Multiple 4 ft. (1.2 m) drops
Weatherproofing: I P64
Wireless UHF Transceiver Frequency: 433 MHz
Range: 200 ft. (61 m), line-of-sight
interrogator and transponder
Protocol: Echopoint Protocol
Wireless (LF Transmitter) Frequency: 123 kHz
Range: Up to 3.5 ft. (1.1 m)
Air Protocols: ISO 18000-7, EchoPoint, ANSI
INCITS 256