User Manual

Special Effects
The Savage RGB Pro Panel is capable of 35 unique special effects. In RGB mode press the “Intensity/
Menu” button one time. Turn the “Menu” button clockwise until “Cycle Effects” is highlighted. Press the
“Intensity/Cycle” button again and the available special effects will appear. While “Mode” is highlighted,
turn the “Intensity/Mode” button clockwise and to scroll through the various effects.
Fade effects: 37-47, 83
Strobe effects: 48- 55, 84-86
Pulsating effects: 56-59, 81-82, 87
Flickering replace: 102
To increase or decrease the speed of the effect, turn the “Color” knob until “Speed” is highlighted.
Turn the “Intensity/Menu” button to adjust the speed. 1 is the slowest speed and 32 is the fastest.
CYCLE SPECIAL EFFECTS
DMX OPERATION
EFFECT NUMBER
EFFECT SPEED
EFFECT NAME
Party lights/ re works: 103
Flashing police car lights: 104
Television screen: 105
Lightning ashes: 106
DMX INPUT/OUTPUT
DMX Operation
Connect the DMX output to the Savage RGB Pro Panel and turn the panel on.
The panel should automatically detect the controller and switch to DMX mode. The panel display will
say: “DMX 512 with RGB..” Below the readout, the channel information will display.
Channel 1: Center Channel 2: Red Channel 3: Green Channel 4: Blue
The DMX512 will default to channel one, but four channels are supported. Set channel one to any
number above zero (we recommend the 50% position). The panel’s functions supported in DMX mode
are RGB, hue/saturation/intensity and CCT. Red, green and blue can now be controlled individually.
To change modes. Press the “Menu/Intensity” button one time. The menu will display the following:
DMX
1/SW 2/R 3/G 4/B 1/SW 2/I 3/S 4/H 1/SW 2/BRI 3/CCT
The number before each letter is the channel number for the selected function. The rst line is the
RGB mode and when selected will allow the user to make red, green and blue adjustments. The
second line allows the user to adjust the intensity, saturation and hue of the selected color. The third
line allows the user to switch to CCT mode. To change modes, rotate the “Menu/Intensity” clockwise
until the desired mode is highlighted. Press the “Intensity/Menu” button again and the light will switch
to the selected mode and be controllable with the DMX controller.
RGB Mode
To start: make sure the toggle is set to RGB and then press the “Menu” button until “Menu” is visible
at the top.
The panel will default to “Hue” selection. In this mode, you can select from any of 360 different colors.
Press the “Color” button until “Hue” is highlighted. Turn the “Color” knob until the desired color is
selected.
0 = Red 120 = Green 240 = Blue
Numbers in between represent colors between red, green and blue. After the desired color is selected,
press the “Color” button one time and “Sat” will be highlighted. This feature allows for adjustment
of the saturation of the selected color. Turn the “Color” button clockwise to increase saturation and
counterclockwise to reduce saturation.
Turn the “Intensity/Menu” button clockwise to increase brightness and counterclockwise to reduce
brightness at any selected color temperature.
To ne tune a selected color, press in the “Intensity/Menu” button. Turn the menu button clockwise
until “RGBW Dimming” is selected. Press the “Menu” button again. The menu will default to the “R”/
red adjustment. You can adjust up or down to increase or decrease the amount of red in your selected
color by turning the “Menu” button clockwise to increase or counterclockwise to decrease.
Turn the “Color” button clockwise to adjust “G”/ green in the selected color.
Turn again to adjust “B”/ blue.
Turn to the “W” or white position to increase or decrease the saturation of the selected color.
The panel can save up to 8 desired colors for future use. Select a desired RGB color, Press the
“Menu” button until the “Hue” menu is present. Turn the “Color” button clockwise until “Hue” is
highlighted. Scroll to the color you wish to save. Press the “Menu” button until “Menu” is displayed.
Turn the “Menu” button until “Preset Colors” is highlighted. Press the “Menu” button a second time
and the panel will go dark. Press the “Color” knob again and the selected color will be saved.Turn the
“Color” knob clockwise and select any number 1-8 that you would like to save the selected color to.
The panel will then go to that color any time that number is selected. To overwrite a previously
selected color, repeat above steps after selecting the corresponding number associated with the
previously selected color.
RGB MODE
RGB ADJUSTMENT
COLOR ADJUST BRIGHTNESS ADJUST
COLOR
FINE TUNE RGB
SATURATION
SAVE COLORS
INTENSITY
SPECIAL EFFECTS
RGB PRO PANEL
USAGE INSTRUCTIONS
®
®