Manual

7
8. Put the action and barrel in a padded vise.
9. Remove the magazine housing assembly
screws, and remove the magazine housing.
See FIGURE 6.
10. Remove the front stud and barrel clamp.
See FIGURE 6.
11. Remove the receiver and ejector from the
barrel.
12. Remove the cocking handle and slide the
bolt forward and out of the receiver. See
FIGURE 6.
DO NOT DISASSEMBLE THE BOLTASSEMBLY.
CAUTION
B O LT ASSEMBLIES ARE SPECIFICALLY
M ATCHED TO A FIREARM. USING A N Y
OTHER BOLT A S S E M B LY M AY C A U S E
EXTENSIVE DAMAGE TO THE FIREARM
AND/OR SERIOUS INJURY TO THE SHOOTER
OR BYSTANDER.
DISASSEMBLE ONLY ONE FIREARM AT A
TIME TO AVOID INTERCHANGING
COMPONENTS.
CLEANING THE BORE
LOOK AND FEEL! BE SURE THE CHAMBER
AND MAGAZINE ARE COMPLETELY EMPTY —
DO NOT ASSUME!!!
NEVER ATTEMPT TO DISASSEMBLE, CLEAN,
OR OIL A LOADED FIREARM!
BE SURE TO READ AND UNDERSTAND ALL
OF THE CAUTIONS AND WARNINGS ON ALL
SOLVENTS AND CHEMICALS PRIOR TO USE.
FOLLOW THE MANUFA C T U R E R ’ S
INSTRUCTIONS FOR BEST CLEANING
RESULTS.
1. Prepare an area for cleaning the firearm with a
suitable surface, adequate ventilation, and the
correct caliber cleaning rod, brush, patches,
powder solvent, and oil.
2. Follow the instructions under “TO
DISASSEMBLE THE ACTION” (see page 6)
before cleaning.
3. Lay the firearm horizontally with the ejection
port facing down.
A LWAYS STA RTING FROM THE CHAMBER
END, PUSH THE CLEANING ROD THROUGH
THE BORE AND OUT THE MUZZLE END.
4. Using a small amount of powder solvent on the
brush, push the cleaning rod through the barrel
several times.
5. Unscrew the brush from the cleaning rod and
replace it with a patch tip.
6. Push a new patch through the bore starting
from the chamber end and out the muzzle.
7. Repeat step 6 several times.
8. Push a new patch lightly saturated with gun oil
through the bore.
9. Push a new dry patch through the bore to
remove the excess oil.
A VERY THIN FILM OF OIL IS SUFFICIENT
PROTECTION – DO NOT OVER OIL!!!
YOUR GUN IS A MECHANICAL DEVICE THAT
WILL NOT LAST FOREVER AND IS SUBJECT
TO WEAR. CONTACT S AVAGE A R M S
S E RVICE DEPA RTMENT FOR PERIODIC
INSPECTION, ADJUSTMENT AND SERVICE.
8
PROTECTING METAL SURFACES
1. In order to be able to reach all surfaces,
remove the bolt prior to cleaning and oiling.
2. With a soft cloth, remove any foreign matter
(i.e. mud, twigs, grass).
3. Apply a thin coat of gun oil on all cleaned
metal surfaces. Rubbing may be necessary to
remove any signs of rust.
4. Where accessible, clean and lightly oil interior
metal surfaces.
TO REASSEMBLE THE ACTION
REVERSE THE PROCEDURES UNDER “TO
DISASSEMBLE THE ACTION” (SEE PAGE 6).
SECTION 3
RINGS & BASES FOR MOUNTING A
S C O P E
The following Companies manufacturer RINGS
and BASES that fit Savage firearms.
The manufacturers listed below should be
contacted for specific part numbers and
information.
SECTION 4
S TATEMENT OF LIMITED
WA R R A N T Y
Please complete the WARRANTY
REGISTRATION CARDand return it to Savage
Arms, Inc. within ten (10) days from the date of
purchase.
Savage Arms, Inc. must be notified within one
(1) year from the date of purchase of any defect
in materials or workmanship encountered during
normal use.
WHO IS COVERED?
The original owner (with proof of purchase).
WHAT IS COVERED?
Any defect in materials or workmanship
performed at Savage Arms.
HOW LONG IS THE WARRANTY PERIOD?
One (1) year from the date of purchase.
WHAT IS NOTCOVERED?
PERSONAL INJURY, PROPERTYDAMAGE,
AND/OR DAMAGE TO THE FIREARM CAUSED
BY:
• Negligence to provide proper care and
maintenance.
• Alterations/modifications performed without
the expressed authorization of Savage
Arms, Inc. Service Department.
• Normal wear; tear; and/or corrosion.
• Accidental discharge, careless handling,
and/or misuse.
• Barrel obstructions.
WEAVER
P.O. Box 39
Onalaska, WI 54650
800-635-7656
www.weaveroptics.com
BURRIS
331 East 8
th
Street
Greeley, CO 80631
970-356-1670
www.burrisoptics.com
KWIK-SITE
5555 Treadwell
Wayne, MI 48184
734-326-1500
[e-mail]
MILLETT
7275 Murdy Circle
Huntington Beach, CA
92647
800-645-5388
www.millettsights.com
B-SQUARE
P.O. Box 11281
Fort Worth, TX 76110
800-433-2909
www.b-square.com
LEUPOLD
14400 NW Greenbrier
Parkway
Beaverton, OR 97006
503-526-5196
www.leupold.com