sauder.com A little "bonjour" for your bathroom. Linen Tower Model 414817 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-445-1527. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-25 Lot #: 501734 Date Purchased: __________________ 04/04/17 Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-25 Safety 26 Warranty 27 Page 2 Not actual size Skip the power trip. This time. www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Fasten four ANGLE BRACKETS (3) to the MOLDINGS (E). Use four BLACK 1/2" PAN HEAD SCREWS (15). å Fasten the MOLDINGS (E) to the TOP (C) and SHELF (G). Use four BLACK 1/2" PAN HEAD SCREWS (15). å Turn four ANGLED HEAD CAM SCREWS (2) into the SHELF (G).
Step 2 å Fasten the TOP (C) to the UPPER ENDS (A and B). Use four BLACK 1-1/2" FLAT HEAD SCREWS (14). Remember: Righty tighty. Lefty loosey. Caution 14 Do not stand the unit upright without the BACK fastened. The unit may collapse. BLACK 1-1/2" FLAT HEAD SCREW (4 used in this step) Finished edge E C Sur fac ew ith hol es A B Sur fac ew itho ut h ole s Page 6 www.sauder.
Step 3 å Fasten the SHELF (G) to the UPPER ENDS (A and B). Use four BLACK 1-1/2" FLAT HEAD SCREWS (14). A E B G 14 BLACK 1-1/2" FLAT HEAD SCREW (4 used in this step) 414817 www.sauder.
Step 4 Turn six CAM SCREWS (2) into the LEGS (M and N). å å å Push six HIDDEN CAMS (1) into the LOWER ENDS (H and J). Fasten the LEGS (M and N) to the ENDS (H and J). Tighten six HIDDEN CAMS. 1 2 Angled head 3 1 The arrow must point toward the edge of the board. These edges should be even. These edge should be even. These surfaces should be even. 1 N J 2 H M (6 used) These surfaces should be even. 2 Page 8 www.sauder.
Step 5 å You have the option to assemble the DOOR to open to the left or the right of your cabinet. Follow the diagram based on your preference. å Fasten the HINGE BRACKETS (8) to the LOWER RIGHT END (J). Use the screws in the HINGES. å Fasten a DOOR STOP (4) to the LOWER LEFT END (H). Use two BLACK 1/2" PAN HEAD SCREWS (15). DOOR OPENING RIGHT 8 15 BLACK 1/2" FLAT HEAD SCREW (2 used in this step) J 4 H 15 å Fasten the HINGE BRACKETS (8) to the LOWER LEFT END (H). Use the screws in the HINGES.
Step 6 å Fasten the LOWER ENDS (H and J) to the BOTTOM (K). Use four BLACK 1-1/2" FLAT HEAD SCREWS (14). NOTE: The remaining views show the DOOR opening to the right. Finished edge N J M Sur fac ew ith hol es Sur fac ew itho ut h ole s H K 14 BLACK 1-1/2" FLAT HEAD SCREW (4 used in this step) Page 10 www.sauder.
Step 7 å å Push four HIDDEN CAMS (1) into the LOWER ENDS (H and J). Now might be a good time to refresh your drink. Fasten the LOWER ENDS (H and J) to the SHELF (G). Tighten four HIDDEN CAMS. 1 2 3 1 The arrow must point toward the edge of the board. 1 G J H 414817 www.sauder.
Step 8 å å å å å Carefully turn your unit over onto its front edges. Lay the UPPER BACK (D) over the upper opening of your cabinet. å Make equal margins along the bottom and side edges of the LOWER BACK (I). Push on opposite corners of your unit if needed to make it "square". å å å Fasten the LOWER BACK (I) to your unit using the remaining NAILS (6). Make equal margins along the top and side edges of the BACK (D). Push on opposite corners of your unit if needed to make it "square".
Step 9 å Carefully stand your unit upright in its final location against a wall. å Push the RUBBER SLEEVES (12) over the METAL PINS (11). Insert the METAL PINS into the hole locations of your choice in the ENDS (A, B, H and J). Set the ADJUSTABLE SHELVES (F) onto the METAL PINS. F B A F 11 12 (12 used) H J F 414817 www.sauder.
Step 10 å Fasten the HINGES (7) to the DOOR (L). Use four SILVER 1/2" FLAT HEAD SCREWS (17). å Fasten the KNOB (13) to the DOOR (L). Use a BLACK 7/8" MACHINE SCREW (16). 17 SILVER 1/2" FLAT HEAD SCREW (4 used in this step) 16 7 BLACK 7/8" MACHINE HEAD SCREW (1 used in this step) L 13 Page 14 www.sauder.
Step 11 å Fasten the DOOR (L) to the LOWER END with the HINGE BRACKETS. Slide the HINGES (12) onto the HINGE BRACKETS on the LOWER END. å Secure the DOOR with the mounting screw on the HINGE BRACKET. See the next step for adjustments. Mounting screw L 414817 www.sauder.
Step 12 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 13 å We recommend using the FURNITURE TIPPING RESTRAINT KIT (99) for added stability. Fasten a bracket to the back edge of the TOP (C) using the 5/8" screw as shown. å Follow the instructions included in the KIT to fasten your unit to the wall. Almost time to celebrate! With a nap. Use the 5/8" screw through the small hole in a bracket and into the back edge of the TOP (C). Small hole 99 C 414817 www.sauder.
Step 14 å å å å Peel a screw cover from the SCREW COVER CARD (10) and stick them onto the visible screw heads. Using your hammer, gently tap a CAM COVER (9) onto each HIDDEN CAM. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? 20 lbs. 25 lbs. 25 lbs. 25 lbs. 25 lbs.
Modèle 414817 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer les EXTRÉMITÉS INFÉRIEURES (H et J) au DESSOUS (K). Utiliser quatre VIS TÊTE PLATE 38 mm NOIRES (14). Fixer quatre CONSOLES À ÉQUERRE (3) aux MOULURES (E). Utiliser quatre VIS TÊTE GOUTTE DE SUIF 13 mm NOIRES (15). Fixer les MOULURES (E) au DESSUS (C) et à la TABLETTE (G). Utiliser quatre VIS TÊTE GOUTTE DE SUIF 13 mm NOIRES (15).
ÉTAPE 9 ÉTAPE 13 Relever, avec précaution, l'élément dans sa position verticale et placer l'élément dans son emplacement final, contre un mur. Il est recommandé d’utiliser le KIT DE RETENUE ANTIBASCULEMENT POUR MOBILIER (99) pour stabilité additionnelle. Fixer une console sur le bord arrière du DESSUS (C) à l’aide de la vis de 16 mm comme l'indique le schéma. Enfoncer les MANCHONS EN CAOUTCHOUC (12) sur les GOUPILLES EN MÉTAL (11).
Modelo 414817 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Usted tiene la opción de montar la PUERTA para abrir a la izquierda o a la derecha de su gabinete. Siga el diagrama basado en su preferencia. Fije cuatro SOPORTES ANGULARES (3) a las MOLDURAS (E). Utilice cuatro TORNILLOS NEGROS DE CABEZA REDONDA de 13 mm (15). Fije las MÉNSULAS DE BISAGRA (8) al EXTREMO DERECHO INFERIOR (J). Utilice los tornillos provistos de las BISAGRAS.
PASO 8 PASO 9 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Cuidadosamente ponga la unidad en posición vertical y coloque su unidad en su posición final contra una pared. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Coloque el DORSO SUPERIOR (D) sobre la abertura superior de la unidad. Empuje los MANGUITOS DE GOMA (12) sobre las ESPIGAS DE METAL (11).
PASO 11 PASO 13 Fije la PUERTA (L) al EXTREMO INFERIOR con las MÉNSULAS DE BISAGRA. Deslice las BISAGRAS (12) sobre las MÉNSULAS DE BISAGRA sujetadas al EXTREMO INFERIOR. Le recomendamos utilizar el KIT DE CONTROL ANTIINCLINACIÓN PARA MOBILIARIO (99) para dar más estabilidad. Fije un soporte al borde posterior del PANEL SUPERIOR (C) con el tornillo de 16 mm como se muestra. Fije la PUERTA con el tornillo de montaje de la MÉNSULA DE BISAGRA. Consulte el próximo paso para los ajustes.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Properly mounting the cabinet to the wall. • If not properly mounted, the cabinet can tip over and cause injury and damage. • Carefully review and follow the mounting instructions contained in this manual. • Use the supplied safety bracket for added stability.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 1-800-445-1527 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
