sauder.com Deep shelves for tall tales. Library with Doors Dakota Pass Collection | Model 420409 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 389559 05/04/16 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 420409 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A and B) and SHELF/BOTTOMS (D). Some assembly (and snacks) required. Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F D D 10F B A www.sauder.
Step 2 å Turn fourteen CAM SCREWS (8F) into the FRONT LEGS (G and H) and TOP MOLDING (K). å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B) and TOP (C). 8F (14 used) H K G Arrow 1F B (14 used) A Arrow C Hole Arrow The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 1F 420409 www.sauder.
Step 3 å Fasten the BACK LEGS (I) to the ENDS (A and B). Use twelve BLACK 2-1/4" FLAT HEAD SCREWS (26S). These surfaces should be even. These surfaces should be even. I Angled edge S HI urfa DD ce EN wit CA h M S B S HI urfa DD ce EN wit CA h M S A I Angled edge 26S BLACK 2-1/4" FLAT HEAD SCREW (12 used in this step) www.sauder.
Step 4 Fasten the ENDS (A and B) to the TOP (C). Tighten four TWIST-LOCK® FASTENERS. å Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 5 å Using your hammer, tap two MOLDING CONNECTORS (17F) into the notches in the TOP MOLDING (K). å Then, fasten the TOP MOLDING (K) to the TOP (C). Tighten two HIDDEN CAMS. 1 Flat end 2 17F Flat end 17F K K C www.sauder.
Step 6 å Insert two WOOD DOWELS (15F) into the FRONT LEGS (G and H). å Fasten the FRONT LEGS (G and H) to the ENDS (A and B). Tighten twelve HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the LEGS insert into the holes in the ENDS. å Using your hammer, gently tap the FRONT LEGS (G and H) onto the MOLDING CONNECTORS in the TOP MOLDING (K). Don't worry. It isn't Rome. This can be built in a day.
Step 7 å å å å Slide the BOTTOM MOLDING* (L) onto the notched edge of one of the SHELF/BOTTOMS (D). å *U.S. Patent No. 5,499,886 Slide an ADJUSTABLE SHELF MOLDING* (M) onto the other SHELF/BOTTOM (D). Repeat this step for the ADJUSTABLE SHELVES (E and J) and the remaining ADJUSTABLE SHELF MOLDINGS (M). NOTE: The top edge of the ADJUSTABLE SHELF MOLDINGS should be even with the top surfaces of the SHELF/BOTTOMS and ADJUSTABLE SHELVES.
Step 8 å NOTE: Place the SHELF/BOTTOM (D) with the ADJUSTABLE SHELF MOLDING (M) first and then the SHELF/BOTTOM (D) with BOTTOM MOLDING (L) in positon before tightening the TWIST-LOCK® FASTENERS. å Fasten the SHELF/BOTTOMS (D) to the ENDS (A and B). Tighten eight TWIST-LOCK® FASTENERS. B D D Page 12 M Sur f TW ace wi IS th FAS T-LO TEN CK® ERS A L Sur f TW ace wi IS th FAS T-LO TEN CK® ERS 420409 www.sauder.
Step 9 å Fasten the EXTENSION BLOCK (O) to the SHELF/ BOTTOM (D). Use two BROWN 1-5/8" FLAT HEAD SCREWS (55S) into the exact holes shown. å Insert the DOOR STOPS (4I) into the center holes on the EXTENSION BLOCK (O). 4I Finished surface O D 55S BROWN 1-5/8" FLAT HEAD SCREW (2 used in this step) www.sauder.
Step 10 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). å Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the SHELF/BOTTOM (D).
Step 11 å Fasten two HINGES (14H) to each DOOR (N). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). 11S BLACK 1/2” FLAT HEAD SCREW (8 used in this step) 14H N N 14H www.sauder.
Step 12 å å Carefully stand your unit upright. å Fasten a DOOR (N) to the LEFT END (B) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. å Fasten the DOOR MOLDING (P) to the DOOR (N). Use two BLACK 1" PAN HEAD SCREWS (60S). å Fasten a KNOB (28K) to the DOOR (N). Use a SILVER 1-1/2" MACHINE SCREW (95S) through the DOOR, through the DOOR MOLDING, and into the KNOB. å å Repeat this step for the other DOOR (N).
Step 13 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 14 å å IMPORTANT: This unit must be positioned against a wall. å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" PAN HEAD SCREW (16S) into a stud in your wall. å å å Push a CAM COVER (13P) onto each visible HIDDEN CAM. Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B).
Modèle 420409 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. À l'aide d'un marteau, enfoncer les deux CONNECTEURS DE MOULURE (17F) dans les crans de la MOULURE DE DESSUS (K). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWISTLOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A et B) et les TABLETTES/DESSOUS (D).
ÉTAPE 9 ÉTAPE 13 Fixer le BLOC D’EXTENSION (O) à la TABLETTE/DESSOUS (D). Utiliser deux VIS TÊTE PLATE 41 mm MARRON (55S) à travers les trous exacts indiqués. Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Enfoncer les ARRÊTS DE PORTE (4I) dans les trous centraux sur le BLOC D'EXTENSION (O). ÉTAPE 10 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer.
Modelo 420409 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los SUJETADORES TWIST-LOCK® en este paso. Utilizando el martillo, ligeramente clave dos CONECTORES DE MOLDURA (17F) dentro de las muescas de la MOLDURA DE PANEL SUPERIOR (K). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A y B) y de los ESTANTES / FONDOS (D).
PASO 9 PASO 13 Fije el BLOQUE DE EXTENSIÓN (O) al ESTANTE / FONDO (D). Utilice dos TORNILLOS MARRONES DE CABEZA PERDIDA de 41 mm (55S) dentro de los agujeros correspondientes indicados. Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Las PUERTAS pueden requerir de ajustes. Siga el texto abajo para hacer los ajustes necesarios. Empuje los TOPES DE PUERTA (4I) en los agujeros centrales en el BLOQUE DE EXTENSIÓN (O).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados. • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
