sauder.com Your center of attention. Credenza Dakota Pass Collection | Model 420408 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-24 Français pg 25-28 Español pg 29-32 Lot # 389552 05/03/16 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Français Assembly Tools Required 3 4 5-24 Straight Edge Screwdriver 25-28 Español 29-32 Safety 33-34 Warranty No. 2 Phillips Screwdriver Tip Shown Actual Size Hammer Not actual size Skip the power trip. This time. 35 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 34E ADJUSTABLE FOOT - 3 17F MOLDING CONNECTOR - 2 4L 1F HIDDEN CAM - 12 14H CURVED HINGE - 4 10F TWIST-LOCK® FASTENER - 14 40H HINGE - 4 35M CARD HOLDER - 2 WARNING LABEL - 1 4I 8F 28K KNOB- 4 DOOR STOP - 4 38M CARD SHEET - 1 CAM SCREW - 12 1N NAIL - 58 WARNING Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the BOTTOM (G). å Repeat this step for the ENDS (A and B) and UPRIGHTS (C, D, and E). 10F (14 used) Do not tighten the TWIST-LOCK® FASTENERS in this step. G 10F www.sauder.
Step 2 å Push twelve HIDDEN CAMS (1F) into the ENDS (A and B) and TOP (F). The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Arrow Hole F B A Arrow 1F (12 used) å Turn twelve CAM SCREWS (8F) into the FRONT LEGS (M and N) and TOP MOLDING (P). 8F N M Page 6 420408 P www.sauder.
Step 3 å Fasten the RIGHT END (A) to the RIGHT FRONT LEG (M). Tighten three HIDDEN CAMS. 1 The LEG will overhang this edge 2 Sur fac ew ith HID DEN CA MS A Edge with TWIST-LOCK® FASTENERS These surfaces should be even. å M Fasten the LEFT END (B) to the LEFT FRONT LEG (N). Tighten three HIDDEN CAMS. Edge with TWIST-LOCK® FASTENERS Sur fac ew ith HID DEN CA B MS These surfaces should be even. N www.sauder.
Step 4 å Fasten the TOP MOLDING (P) to the TOP (F). Tighten six HIDDEN CAMS. P ce rfa Su th wi F EN DD HI S M CA Page 8 420408 www.sauder.
Step 5 å Fasten the UPRIGHTS (C, D, and E) to the TOP (F). Tighten six TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible. Dowel end Unfinished edge out h t i ew ® fac OCK r u S T-L S IS TW TENER FAS www.sauder.
Step 6 å Slide the BOTTOM MOLDING (S) onto the notched edge of the BOTTOM (G). å Slide the SHELF MOLDINGS (Q and R) onto the notched edges of the SHELVES (K and L). å *U.S. Patent No. 5,499,886 rfa Su G ce Notched edge th wi TW LO TIS N TE AS ®F CK S ER These edges must be even. Slide the BOTTOM MOLDING (S) onto the notched edge. S Notched edge K Q K Notched edge Q These edges must be even. Slide the SHELF MOLDINGS (Q) onto the notched edge. Notched edge R L These edges must be even.
Step 7 å Fasten the BOTTOM (G) to the UPRIGHTS (C, D, and E). Use six BLACK 1-15/16" FLAT HEAD SCREWS (113S). Remember: Righty tighty. Lefty loosey. D C Sur f TW ace wi IS th FAS T-LO TEN CK® ERS E G S 113S BLACK 1-15/16" FLAT HEAD SCREW (6 used in this step) www.sauder.
Step 8 å Fasten the ENDS (A and B) to the TOP (F) and BOTTOM (G). Tighten eight TWIST-LOCK® FASTENERS. å Fasten the REAR LEGS (O) to the ENDS (A and B). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S). 26S BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) O A F Angled edge O G B Angled edge Page 12 420408 www.sauder.
Step 9 å å Unfold the BACK (H) and lay it over your unit. å å Fasten the BACK (H) to your unit using the NAILS (1N). Caution Make equal margins along long edges and along the short edges of the BACK (H). Push on opposite corners of your unit if needed to make it "square". Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHTS. 1N NAIL (58 used in this step) These holes must line up over the UPRIGHTS.
Step 10 å å å å Fasten the ADJUSTABLE FEET (34E) to the BOTTOM (G). Use three BLACK 9/16" LARGE HEAD SCREWS (1S) in each FOOT. NOTE: Be sure to use the holes shown. Fasten the ADJUSTABLE FEET (34E) to the BOTTOM (G). Use three BLACK 1-15/16" FLAT HEAD SCREWS (113S). NOTE: Be sure to use the holes shown. 1S BLACK 9/16" LARGE HEAD SCREW (9 used in this step) G 34E 34E 113S BLACK 1-15/16" FLAT HEAD SCREW (3 used in this step) 1S BLACK 9/16" LARGE HEAD SCREW Page 14 420408 www.sauder.
Step 11 å å Fasten the FRONT LEGS (M and N) to TOP MOLDING (P). First push the MOLDING CONNECTORS (17F) into the notches of the LEGS (M and N) and TOP MOLDING (P). Don't worry. It isn't Rome. This can be built in a day. Then, tap the MOLDING CONNECTORS (17F) completely into the notches with a hammer and straight edge screwdriver. 17F N M 17F P M www.sauder.
Step 12 å å Carefully stand your unit upright. Push a DOOR STOP (4I) into each LEFT and RIGHT UPRIGHT (E and D) and two DOOR STOPS (4I) into the UPRIGHT (C). 4I 4I E Page 16 C 420408 D www.sauder.
Step 13 å NOTE: Both HINGES are shown. Carefully look at the HINGES to make sure you have the correct one in this step. å Fasten four CURVED HINGES (14H) to the DOORS (I). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). 11S BLACK 1/2” FLAT HEAD SCREW (8 used in this step) More curve Less curve 14H 40H 14H I I 14H www.sauder.
Step 14 å Fasten four HINGES (40H) to the GLASS DOORS (J). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). 11S BLACK 1/2" FLAT HEAD SCREW (8 used in this step) 40H J J 40H Page 18 420408 www.sauder.
Step 15 å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten a DOOR (I) to the RIGHT END (A). Use the screws in the HINGES. å Fasten a KNOB (28K) to the DOOR (I). Use a 1" MACHINE SCREW (50S). å Repeat this step fastening the other DOOR (I) to the LEFT END (B).
Step 16 å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw å Fasten a GLASS DOOR (J) to the RIGHT UPRIGHT (D). Use the screws in the HINGES. å Fasten a DOOR MOLDING (T) to GLASS DOOR (J). Use two BROWN 1" FLAT HEAD SCREWS (12S). å Fasten a KNOB (28K) to the GLASS DOOR (J). Use a SILVER 1-1/2" MACHINE SCREW (95S).
Step 17 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 18 å å Position your unit in its final location. å IMPORTANT: The ADJUSTABLE FOOT should not extend beyond the bottom edges of the LEGS (M, N, and O). å Cover the holes with three HOLE PLUGS (41P). If you're doing this to help a friend, don't leave without a bite. Open the DOORS. Through the holes in the BOTTOM (G), turn the ADJUSTABLE FOOT (34E) downward until it touches the floor. 41P Make adjustments before covering the holes. N M O G With your No.
Step 19 å Fasten a CARD HOLDER (35M) to a LARGE SHELF MOLDING (R). Use two SILVER 5/8" MACHINE SCREWS (15S). å Separate the CARDS on the CARD SHEET (38M) and insert one into the CARD HOLDER (35M). å Repeat this step using the remaining LARGE ADJUSTABLE SHELF and MOLDING. 15S SILVER 5/8" MACHINE SCREW (4 used for the CARD HOLDERS) L Open end to insert CARDS R 35M 38M 35M www.sauder.
Step 20 å Apply the WARNING LABEL (4L) to the TOP (F). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram. å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. å å Push a CAM COVER (13P) onto each HIDDEN CAM.
Modèle 420408 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Fixer la MOULURE DE DESSUS (P) au DESSUS (F). Serrer six EXCENTRIQUES ESCAMOTABLES. • Vérifier la taille et le poids du téléviseur.
ÉTAPE 9 ÉTAPE 13 Attention Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. REMARQUE : Les deux CHARNIÈRES sont illustrées. Observer soigneusement les CHARNIÈRES pour s’assurer d’avoir la bonne à cette étape. Déplier l'ARRIÈRE (H) et le placer sur l'élément. Fixer quatre CHARNIÈRES INCURVÉES (14H) sur les PORTES (I). Utiliser huit VIS TÊTE PLATE 13 mm NOIRES (11S).
ÉTAPE 17 ÉTAPE 19 Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Fixer une PORTE-CARTES (35M) sur la MOULURE DE LA GRANDE TABLETTE (R). Utiliser deux VIS À MÉTAUX 16 mm ARGENTÉES (15S). Il faut peut-être ajuster les PORTES. Suivre les indications cidessous pour ajuster. Séparer les CARTES de la FEUILLE DE CARTES (38M) et insérer les dans la PORTE-CARTES (35M).
Modelo 420408 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 4 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Fije la MOLDURA DE PANEL SUPERIOR (P) al PANEL SUPERIOR (F). Apriete seis EXCÉNTRICOS ESCONDIDOS. PASO 5 • Verifique el tamaño y peso del televisor.
PASO 9 PASO 13 Precaución NOTA: Se muestran ambas BISAGRAS. Mire con cuidado las BISAGRAS para asegurarse de que tiene la correcta en este paso. No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Desdoble el DORSO (H) y colóquelo sobre la unidad. Los márgenes a lo largo de los bordes largos y cortos del DORSO (H) deben estar uniformes. Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla "cuadrada.
PASO 17 PASO 19 Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Fije un PORTA-TARJETAS (35M) a la MOLDURA DEL ESTANTE GRANDE (R). Utilice dos TORNILLOS PLATEADOS PARA METAL de 16 mm (15S). Las PUERTAS pueden requerir de ajustes. Siga el texto abajo para hacer los ajustes necesarios. Separe las TARJETAS en la HOJA DE TARJETAS (38M) e inserte las en el PORTA-TARJETAS (35M).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
