sauder.com Sit and surf. Desk Dakota Pass Collection | 420196 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-26 Français pg 27-29 Español pg 30-32 Lot # 387393 01/19/16 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-26 Hammer Français 27-29 Español 30-32 Safety 33-34 Warranty Page 2 Not actual size Skip the power trip. This time. 35 420196 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A and B), UPRIGHT (C), BOTTOM (E), and MODESTY PANEL (F). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F 10F E F C 10F B A www.sauder.
Step 2 å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), TOP (D), and BRACE (H). Some assembly (and snacks) required. Do not tighten the HIDDEN CAMS in this step. Arrow 1F (14 used) D C A B Arrow H 1F Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 420196 www.sauder.
Step 3 å Turn fourteen CAM SCREWS (8F) into the RIGHT END (A), UPRIGHT (C), LEGS (I, J, and K), and FRONT MOLDING (O). å NOTE: Use the exact holes shown. (14 used) 8F J K I O A C www.sauder.
Step 4 å Fasten the CABINET RIGHTS (35GA) to the RIGHT END (A) and the CABINET LEFTS (35GB) to the UPRIGHT (C). Use eight GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. 3S GOLD 5/16" FLAT HEAD SCREW (8 used in this step) Roller end 1 2 3 1 2 A S HI urfa DD ce EN wi CA th M S 3 3 2 1 Edge with HIDDEN CAMS 3 C 2 Roller end S HI urfa DD ce EN wi CA th M S 1 Edge with HIDDEN CAMS Page 8 420196 www.sauder.
Step 5 å Fasten the REAR LEGS (L) to the ENDS (A and B) and UPRIGHT (C). Use nine BLACK 2-1/4" FLAT HEAD SCREWS (26S). 26S BLACK 2-1/4" FLAT HEAD SCREW (9 used in this step) L Angled edge C Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S Edge with TWIST-LOCK® FASTENERS L Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S A L Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S B www.sauder.
Step 6 å Fasten the MODESTY PANEL (F) to the LEFT END (B). Tighten three TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 7 å Fasten LEFT END (B) and MODESTY PANEL (F) to the TOP (D). Tighten four TWIST-LOCK® FASTENERS. B F Edge with HIDDEN CAMS D th S wi AM ce C rfa EN Su IDD H www.sauder.
Step 8 å Fasten the UPRIGHT (C) to the TOP (D). Tighten two TWIST-LOCK® FASTENERS. å Fasten the UPRIGHT (C) to the MODESTY PANEL (F). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Insert a WOOD DOWEL (15F) into the hole in the CENTER FRONT LEG (K). å Fasten the CENTER FRONT LEG (K) to the UPRIGHT (C). Tighten three HIDDEN CAMS. å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the hole in the edge of the UPRIGHT.
Step 9 å å Insert two WOOD DOWELS (15F) into the BRACE (H). å NOTE: Be sure the WOOD DOWEL in the BRACE inserts into the hole in the UPRIGHT. Fasten the BRACE (H) to the UPRIGHT (C). Tighten one HIDDEN CAM. 15F C Notched edge th S wi AM ce C rfa EN Su IDD H H 15F www.sauder.
Step 10 å Fasten the BOTTOM (E) to the UPRIGHT (C). Tighten two TWIST-LOCK® FASTENERS. Notched edge th ® wi K ce OC rfa T-L RS Su IS ENE TW ST FA E C Page 14 420196 www.sauder.
Step 11 å å Fasten the RIGHT END (A) to the TOP (D), BOTTOM (E), and BRACE (H). Tighten four TWIST-LOCK® FASTENERS and one HIDDEN CAM. Hey! It's starting to look like something! NOTE: Be sure the WOOD DOWEL in the BRACE inserts into the hole in the RIGHT END. E H D A ut itho® w e fac LOCK r u S IST RS TW TENE FAS www.sauder.
Step 12 å Slide the MOLDINGS* (P and Q) onto the notched edges of the BOTTOM (E) and BRACE (H). å *U.S. Patent No. 5,499,886 Wide edge Groove Notched edge E P H Q Slide the MOLDING onto the notched edge. Wide edge Groove Page 16 420196 www.sauder.
Step 13 å Tap two MOLDING CONNECTORS (17F) into the notches in the FRONT LEGS (I and J). Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the FRONT LEGS (I and J). Flat end 17F Flat end 17F J I www.sauder.
Step 14 å Insert two WOOD DOWELS (15F) into the holes in the FRONT LEGS (I and J). å Fasten the FRONT LEGS (I and J) to the ENDS (A and B). Tighten six HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the FRONT LEGS insert into the holes in the edges of the ENDS. 15F B J A Edge with MOLDING CONNECTOR I 15F Page 18 Edge with MOLDING CONNECTOR 420196 www.sauder.
Step 15 å Gently push the FRONT MOLDING (O) onto the MOLDING CONNECTORS in the FRONT LEGS (I and J). å NOTE: Be sure the CAM SCREWS in the FRONT MOLDING insert into the holes in the edge of the TOP (D). å Fasten the FRONT MOLDING (O) to the TOP (D). Tighten three HIDDEN CAMS. J D I O You may need to gently tap the MOLDING CONNECTORS back in after attaching the FRONT MOLDING. www.sauder.
Step 16 å Carefully turn your unit over onto its front edges. Lay the BACK (G) over your unit. å Make equal margins along the bottom and side edges of the BACK (G). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (G) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 1N NAIL (15 used in this step) Top edge without holes G Page 20 420196 www.sauder.
Step 17 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. R N D14 D15 N 102S SILVER 1" LARGE HEAD SCREW (2 used in this step) å Fasten the DRAWER FRONT MOLDING (R) to the DRAWER FRONT (N). Use two SILVER 1" LARGE HEAD SCREWS (102S). 3 With the palm of your hand, tap the DRAWER BOTTOM down into the groove.
Step 18 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D14 and D15). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Repeat this step for the other drawer. Fasten a DRAWER RIGHT (35GC) to the DRAWER RIGHT SIDE (D14) and a DRAWER LEFT (35GD) to the DRAWER LEFT SIDE (D15). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
Step 19 å Fasten a KNOB (28K) to the SMALL DRAWER FRONT (M). Use a GOLD 1" MACHINE SCREW (50S). å Fasten a KNOB (28K) to the DRAWER FRONT (N) and DRAWER FRONT MOLDING (R). Use a SILVER 1-1/2" MACHINE SCREW (95S). 50S GOLD 1" MACHINE SCREW (1 used in this step) M 28K 95S SILVER 1-1/2" MACHINE SCREW (1 used in this step) R N 28K www.sauder.
Step 20 å Push two FILE GLIDES (4B) onto the top edges of the DRAWER SIDES (D14 and D15). 4B 4B D15 D14 Page 24 420196 www.sauder.
Step 21 å å Carefully stand your unit upright. å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. Pro Tip: Lift with your legs. And, you know, your arms. Push a CAM COVER (13P) onto the three HIDDEN CAMS in the LEFT END (B) and the upper HIDDEN CAMS in the RIGHT END (A) and UPRIGHT (C). 50 lbs. B C 15 lbs.
Step 22 å To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
420196 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer l'EXTRÉMITÉ GAUCHE (B) et VOILE DE FOND (F) au DESSUS (D). Serrer quatre FIXATIONS TWIST-LOCK®. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A et B), le MONTANT (C), le DESSOUS (E) et le VOILE DE FOND (F).
ÉTAPE 13 ÉTAPE 18 Enfoncer deux CONNECTEURS DE MOULURE (17F) dans les crans des PIEDS AVANT (I et J). Insérer une EXCENTRIQUE DE COULISSE (10A) dans les CÔTÉS DE TIROIR (D14 et D15). ÉTAPE 14 Fixer un TIROIR DROIT (35GC) sur le CÔTÉ DROIT DE TIROIR (D14) et un TIROIR GAUCHE (35GD) sur le CÔTÉ GAUCHE DE TIROIR (D15). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 3. Insérer deux CHEVILLES EN BOIS (15F) dans les trous des PIEDS AVANT (I et J).
420196 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije el EXTREMO IZQUIERDO (B) al VELO DE FONDO (F) y al PANEL SUPERIOR (D). Apriete cuatro SUJETADORES TWIST-LOCK®. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A y B), del PARAL (C), del FONDO (E) y del VELO DE FONDO (F).
PASO 13 PASO 18 Ligeramente clave dos CONECTORES DE MOLDURA (17F) en las muescas de las PATAS DELANTERAS (I y J). Inserte un EXCÉNTRICO DE CORREDERA (10A) dentro de los LADOS DE CAJÓN (D14 y D15). Introduzca dos PASADORES DE MADERA (15F) en los agujeros en las PATAS DELANTERAS (I y J). Fije un CAJÓN DERECHO (35GC) al LADO DERECHO DE CAJÓN (D14) y un CAJÓN IZQUIERDO (35GD) al LADO IZQUIERDO DE CAJÓN (D15). Utilice cuatro TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados. • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
