sauder.com Gets on your couch’s good side. Side Table Dakota Pass Collection | 420139 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-19 Français pg 20-22 Español pg 23-25 Lot # 387500 02/10/16 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-19 Hammer Français 20-22 Español 23-25 Safety 26 Warranty 27 Page 2 Not actual size Skip the power trip. This time. 420139 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the SHELF/ BOTTOMS (D) and SLIDING SHELF (J). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F J 10F D D 10F www.sauder.
Step 2 å å å Turn four CAM SCREWS (8F) into the LEGS (G and H). NOTE: Be sure to use the exact holes shown in the LEGS. Push eight HIDDEN CAMS (1F) into the ENDS (A and B). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM except for the side edges of the ENDS. 8F G H Arrow 1F Do not tighten the HIDDEN CAMS in this step. (8 used) Do not insert CAM DOWELS into these edges.
Step 3 å Fasten the BACK LEGS (I) to the ENDS (A and B). Use four BLACK 2-1/4" FLAT HEAD SCREWS (26S). Remember: Righty tighty. Lefty loosey. 26S Edge with CAM DOWELS BLACK 2-1/4" FLAT HEAD SCREW (4 used in this step) These surfaces should be even. Edge with HIDDEN CAMS These surfaces should be even. S HI urfa DD ce EN wi CA th M S A Edge with CAM DOWELS I I S HI urfa DD ce EN wi CA th M S B Angled edge Edge with HIDDEN CAMS www.sauder.
Step 4 å Fasten the LEFT END (B) to the TOP (C). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Edge with HIDDEN CAMS C Sur fac ew ith hol es B th e wi MS c a f Sur EN CA D HID The small hole should be here. I Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 5 å Fasten the SHELF/BOTTOMS (D) to the LEFT END (B). Tighten four TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 6 å Fasten the RIGHT END (A) to the TOP (C) and SHELF/ BOTTOMS (D). Tighten four TWIST-LOCK® FASTENERS and two HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day. Edge with HIDDEN CAMS C D D A t thou i w face MS Sur EN CA D HID I Maximum 210 degrees Arrow Minimum 190 degrees Page 10 420139 www.sauder.
Step 7 å Slide the MOLDINGS* (L and M) onto the notched edges of the SHELF/BOTTOMS (D). å *U.S. Patent No. 5,499,886 Slide the SHELF MOLDING (L) onto the notched edge. Notched edge L D M D Slide the BOTTOM MOLDING (M) onto the notched edge. www.sauder.
Step 8 å Insert two WOOD DOWELS (15F) into the FRONT LEGS (G and H). å Fasten the FRONT LEGS (G and H) to the ENDS (A and B). Tighten four HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the FRONT LEGS insert into the holes in the ENDS. 1 2 Flat edge H G Flat edge B A 15F Page 12 420139 www.sauder.
Step 9 å å å å Carefully stand your unit upright. Separate the EXTENSION SLIDES (Q) from the EXTENSION RAILS (P) as shown in the upper diagram below. Be prepared, the parts are greasy. Fasten the EXTENSION RAILS (P) to the ENDS (A and B). Use four GOLD 5/16” FLAT HEAD SCREWS (3S) through holes #1 and #4. NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagrams.
Step 10 å Carefully turn your unit over onto its front edges. Lay the BACK (E) over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (E) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 1N NAIL (18 used in this step) E Page 14 420139 www.sauder.
Step 11 å NOTE: You have the option to fasten your DOOR (F) to the right or left side of your unit. The following steps will show the DOOR being fastened to the left side of your unit. DOOR ON LEFT F DOOR ON RIGHT F www.sauder.
Step 12 å å å Carefully stand your unit upright. å Fasten the DOOR (F) to the LEFT END (B) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. å å Fasten the DOOR MOLDING (O) to the DOOR (F). Use two BLACK 1" PAN HEAD SCREWS (60S). å å Push the DOOR STOP (4I) into the hole in the RIGHT END (A). Fasten two HINGES (14H) to the DOOR (F). Use four BLACK 1/2" FLAT HEAD SCREWS (11S).
Step 13 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal) turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 14 å Fasten the TOP MOLDING (K) to the SLIDING SHELF (J). Tighten two TWIST-LOCK® FASTENERS. å Turn the SLIDING SHELF (J) over and fasten the EXTENSION SLIDES (Q) to the SLIDING SHELF. Use four BLACK 1" PAN HEAD SCREWS (60S) through holes #1 and #3. This hole should be closer to this edge.
Step 15 å To insert the SLIDING SHELF (J) into your unit, line up the EXTENSION SLIDES on the SHELF with the EXTENSION RAILS on the unit and push the SHELF into the unit until the SHELF is fully inserted. The SHELF will push in hard until it is all the way in, then it will slide in and out easier. å å å Push a CAM COVER (13P) onto each visible HIDDEN CAM on the ENDS (A and B). NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
420139 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer les pièces TABLETTE/DESSOUS (D) à l'EXTRÉMITÉ GAUCHE (B). Serrer quatre FIXATIONS TWIST-LOCK®. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous dans les TABLETTES/DESSOUS (D) et de la TABLETTE COULISSANTE (J).
ÉTAPE 10 ÉTAPE 13 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Avec précaution, retourner l'élément sur ses chants avant. Placer l'ARRIÈRE (E) sur l'élément. Il faut peut-être ajuster les PORTES. Suivre les indications cidessous pour ajuster. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (E).
420139 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije las partes ESTANTE/FONDO (D) al EXTREMO IZQUIERDO (B). Apriete cuatro SUJETADORES TWIST-LOCK®. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los ESTANTES / FONDOS (D) y del ESTANTE DESLIZANTE (J).
PASO 10 PASO 13 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Coloque el DORSO (E) sobre la unidad. Los márgenes a lo largo de todos los bordes del DORSO (E) deben estar uniformes. Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla "cuadrada.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves. Place the heavier items on the lower shelves.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
