sauder.com Cooler headboards prevail. Full/Queen Headboard Carson Forge Collection | 419887 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-14 Français pg 15-16 Español pg 17-18 Lot # 385536 12/14/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-14 Hammer Français 15-16 Not actual size Español 17-18 Electric drill with 1/4" bit (ONLY in indicated step) Warranty Page 2 19 419887 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A END (2) E PANEL (2) I TIE PLATE (2) B TOP (1) F TOP PANEL (1) J TOP MOLDING (1) C UPPER PANEL (1) G RIGHT LEG (1) K MOLDING (3) D LOWER PANEL (1) H LEFT LEG (1) I B A F K I G J K E K E A C H www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F HIDDEN CAM - 8 7F TWIST-LOCK® FASTENER - 4 13M WASHER - 8 24M NUT - 4 10S SILVER 1-1/8" FLAT HEAD SCREW - 42 8F CAM SCREW - 8 87M CORNER ACCENT - 2 15S SILVER 5/8" MACHINE SCREW - 2 94S SILVER 2" BOLT - 4 Page 4 419887 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F) into the large holes in the TOP PANEL (F). Some assembly (and snacks) required. Do not tighten the TWIST-LOCK® FASTENERS in this step. 7F F www.sauder.
Step 2 å å Turn eight CAM SCREWS (8F) into the LEGS (G and H). Push eight HIDDEN CAMS (1F) into the ENDS (A). H G 8F (8 used) Arrow 1F A Arrow A 1F (8 used) Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 419887 www.sauder.
Step 3 å Fasten the ENDS (A) to the LEGS (G and H). Tighten eight HIDDEN CAMS. å Fasten two CORNER ACCENTS (87M) to both LEGS (G and H). Use two SILVER 5/8" MACHINE SCREWS (15S). 15S SILVER 5/8" MACHINE SCREW (2 used in this step) A 87M Sur HIDface w DEN ith CA MS Edge with CAM DOWELS H A S ur HIDface w DEN itho CA ut MS G 87M (2 used) 1 Edge with CAM DOWELS 2 www.sauder.
Step 4 Fasten the TOP MOLDING (J) to the TOP PANEL (F). Use four SILVER 1-1/8" FLAT HEAD SCREWS (10S). FA S T E N E R S å S ur fa ce w ith T W IS TLO C K ® Edge with TWIST-LOCK® FASTENERS F J 10S SILVER 1-1/8" FLAT HEAD SCREW (4 used in this step) Rounded edge Page 8 419887 www.sauder.
Step 5 å Fasten the TOP PANEL (F) to the LEGS (G and H). Use two SILVER 1-1/8" FLAT HEAD SCREWS (10S). Don't worry. It isn't Rome. This can be built in a day. Edge with TWIST-LOCK® FASTENERS 10S F A Su rfa ce wi th TW IS TLO CK ®F AS TE NE RS SILVER 1-1/8" FLAT HEAD SCREW (2 used in this step) A Sur fac ew ith HID DEN CA MS H Sur fac ew itho ut H IDD EN CA MS G www.sauder.
Step 6 å Fasten three MOLDINGS (K) and two PANELS (E) to LEGS (G and H). Use ten SILVER 1-1/8" FLAT HEAD SCREWS (10S). å NOTE: You may want to put some foam or packing material under the MOLDINGS (K) and PANELS (E) for support.
Step 7 å Fasten the PANELS (C and D) to the LEGS (G and H). Use eight SILVER 1-1/8" FLAT HEAD SCREWS (10S). 10S SILVER 1-1/8" FLAT HEAD SCREW (8 used in this step) S m urfa or ce e w ho it le h s S m urfa or ce e w ho it le h s Finished edge C D H Finished edge G www.sauder.
Step 8 å Fasten two TIE PLATES (I) to PANELS (C, D, E, and F) and MOLDINGS (K). Use eighteen SILVER 1-1/8" FLAT HEAD SCREWS (10S). Hey! It's starting to look like something! 10S SILVER 1-1/8" FLAT HEAD SCREW (18 used in this step) Finished surface These edges must be even. I I F K E C K E Page 12 D K 419887 www.sauder.
Step 9 å Fasten the TOP (B) to the TOP PANEL (F). Tighten four TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible. Dowel end Flat edge B F www.sauder.
Step 10 å å Carefully stand your unit upright. å Fasten the headboard to your frame. Use four SILVER 2" BOLTS (94S), eight WASHERS (13M), and four NUTS (24M) through the LOWER PANEL (D). å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. To attach to a bed frame, determine the height of your bed frame. Pre-drill holes for bolts, washers and nuts with a 1/4" drill bit.
Tête de lit (Lit grand format et Lit très grand format) 419887 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer les PANNEAUX (C et D) aux PIEDS (G et H). Utiliser huit VIS TÊTE PLATE 28 mm ARGENTÉES (10S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (7F) dans les gros trous dans le PANNEAU SUPÉRIEUR (F). ÉTAPE 2 ÉTAPE 8 Fixer deux PLAQUES D'ATTACHE (I) aux PANNEAUX (C, D, E et F) et aux MOULURES (K).
Cabecera para cama de tamaño matrimonial o "reina" 419887 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije los PANELES (C y D) a las PATAS (G y H). Utilice ocho TORNILLOS PLATEADOS DE CABEZA PERDIDA de 28 mm (10S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (7F) dentro de los agujeros grandes del PANEL SUPERIOR (F).
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
