sauder.com Smart stand for the idiot box. TV Stand 419232 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-445-1527. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-24 Français pg 25-28 Español pg 29-32 Share your journey! Lot #: 387095 Date Purchased: __________________ 11/20/15 Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-24 Hammer Français 25-28 Español 29-32 Safety 33-34 Warranty Not actual size Skip the power trip. This time. 35 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Insert thirteen CAM SCREWS (4) into the TOP (E). 4 (13 used) E 419232 www.sauder.
Step 2 å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the right enlarged diagram. Be prepared, the parts are greasy. å Fasten the EXTENSION RAILS (1) to the UPRIGHTS (C and D). Use six 1/2" PAN HEAD SCREWS (17). å å NOTE: Use the exact holes shown in the RAILS. Insert sixteen WOOD DOWELS (7) into the exact holes shown in the ENDS (A and B) and UPRIGHTS (C and D).
Step 3 å Turn six CAM SCREWS (4) into the exact holes shown in the REAR CORNERS (L and M) and BACK (H). å Insert ten WOOD DOWELS (7) into the exact holes shown in the REAR CORNERS (L and M) and BACK (H). (6 used) 4 M L H 7 (10 used) 419232 www.sauder.
Step 4 å å Insert two HIDDEN CAMS (3) into the BACK (H). å NOTE: Be sure the WOOD DOWELS in the edges of the BACK insert into the holes in the REAR CORNERS. 1 2 Fasten the REAR CORNERS (L and M) to the BACK (H). Tighten two HIDDEN CAMS. 3 The arrow must point toward the edge of the board. 3 M 3 3 H L Page 8 www.sauder.
Step 5 å Turn six CAM SCREWS (4) into the exact holes shown in the FRONT PANELS (I and J) and FRONT CORNERS (K). å Insert fourteen WOOD DOWELS (7) into the exact holes shown in the FRONT PANELS (I and J) and FRONT CORNERS (K). (6 used) 4 K J I K 7 (14 used) 419232 www.sauder.
Step 6 å å Insert two HIDDEN CAMS (3) into the FRONT PANELS (I and J). å NOTE: Be sure the WOOD DOWELS in the edges of the FRONT PANELS insert into the holes in the FRONT CORNERS. Fasten the FRONT CORNERS (K) to the FRONT PANELS (I and J). Tighten two HIDDEN CAMS. 3 K J 3 I K Page 10 www.sauder.
Step 7 å Insert four HIDDEN CAMS (3) into the ENDS (A and B) and UPRIGHTS (C and D). å Fasten the ENDS (A and B) and UPRIGHTS (C and D) to the FRONT PANELS (I and J) and FRONT CORNERS (K). Tighten four HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the edges of the ENDS and UPRIGHTS insert into the holes in the FRONT PANELS and FRONT CORNERS. (4 used) 3 K I A J C K D B 419232 www.sauder.
Step 8 å Insert four HIDDEN CAMS (3) into the ENDS (A and B) and UPRIGHTS (C and D). å Fasten the ENDS (A and B) and UPRIGHTS (C and D) to the BACK (H) and REAR CORNERS (L and M). Tighten four HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the edges of the ENDS and UPRIGHTS insert into the holes in the BACK and REAR CORNERS. (4 used) 3 M D H B J L C A Page 12 I www.sauder.
Step 9 å å NOTE: You may need someone's help in this step. å Fasten the ENDS (A and B), UPRIGHTS (C and D), BACK (H), and FRONT PANELS (I and J) to the TOP (E). Tighten thirteen HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the edges of the ENDS, UPRIGHTS, BACK, FRONT PANELS, and CORNERS insert into the holes in the TOP. Insert thirteen HIDDEN CAMS (3) into the ENDS (A and B), UPRIGHTS (C and D), BACK (H), and FRONT PANELS (I and J). (13 used) 3 M D B H K J E C L A I K 419232 www.sauder.
Step 10 å Fasten the BOTTOM (F) to the ENDS (A and B), UPRIGHTS (C and D), BACK (H), and FRONT PANELS (I and J). Use thirteen 1-1/2" FLAT HEAD SCREWS (12). å NOTE: Be sure the WOOD DOWELS in the edges of the ENDS, UPRIGHTS, BACK, FRONT PANELS, and CORNERS insert into the holes in the BOTTOM. 12 1-1/2" FLAT HEAD SCREW (13 used in this step) M F D B H K J L C A I K Page 14 www.sauder.
Step 11 Fasten the BRACES (P and R) to the LEG ASSEMBLIES (N and O). Use sixteen 1/2" MACHINE SCREWS (16). å 16 1/2" MACHINE SCREW (16 used in this step) O These holes must be here. R R N P P Surface with no holes Surface with no holes 419232 www.sauder.
Step 12 å Fasten the LEG ASSEMBLIES (N and O) and BRACES (P) to the BOTTOM (F). Tighten ten 1-3/8" MACHINE SCREWS (13). 13 1-3/8" MACHINE SCREW (10 used in this step) O P N F H K J P Surface with no holes I K Page 16 Surface with no holes www.sauder.
Step 13 å å Carefully turn your unit over onto its front edges. Fasten the BACK BRACES (Q) to the LEG ASSEMBLIES (N and O). Use four 1/2" MACHINE SCREWS (16). 16 1/2" MACHINE SCREW (4 used in this step) O Q Q N 419232 www.sauder.
Step 14 å Fasten the SHELVES (G) to the LEG ASSEMBLIES (N and O) and SHELF BRACES (R). Use ten 1-1/4" FLAT HEAD SCREWS (14). O G G N R R 14 1-1/4" FLAT HEAD SCREW (10 used in this step) Page 18 www.sauder.
Step 15 å Turn four SMALL CAM SCREWS (6) into the exact holes shown in the DRAWER FRONT (S). 6 S 419232 www.sauder.
Step 16 å å å Insert two SMALL WOOD DOWELS (8) into the DRAWER SIDES (U and V). å å å NOTE: Be sure the WOOD DOWELS in the DRAWER SIDES insert into the holes in the DRAWER FRONT. Insert four SMALL HIDDEN CAMS (5) into the DRAWER SIDES (U and V) and DRAWER BRACE (X). Fasten the DRAWER SIDES (U and V) and DRAWER BRACE (X) to the DRAWER FRONT (S). Tighten four SMALL HIDDEN CAMS. Push two CAM COVERS (10) onto the SMALL HIDDEN CAMS in the DRAWER SIDES (U and V).
Step 17 å Fasten the DRAWER BACK (T) to the DRAWER SIDES (U and V) and DRAWER BRACE (X). Use six 1-1/4" FLAT HEAD SCREWS (14). 14 1-1/4" FLAT HEAD SCREW (6 used in this step) Be sure the DRAWER BOTTOM inserts into the DRAWER BACK groove. V T X U 419232 www.sauder.
Step 18 å Fasten the EXTENSION SLIDES (2) to the DRAWER SIDES (U and V). Use six 1/2" PAN HEAD SCREWS (17). å å NOTE: Use the exact holes shown in the SLIDES. Fasten the KNOB (9) to the DRAWER FRONT (S). Use two 3/4" MACHINE SCREWS (15). 2 Open end Mounting holes 17 1/2" PAN HEAD SCREW (6 used for the SLIDES) 9 2 S V Open end U 2 15 3/4" MACHINE SCREW (2 used for the KNOB) Open end Page 22 www.sauder.
Step 19 å å Carefully stand your unit upright. To insert the drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. 419232 www.sauder.
Step 20 å Apply the WARNING LABEL (18) to the TOP (E). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram. å å å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
419232 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Enfoncer deux EXCENTRIQUES ESCAMOTABLES (3) dans l'ARRIÈRE (H). Fixer les COINS ARRIÈRE (L et M) à l'ARRIÈRE (H). Serrer deux EXCENTRIQUES ESCAMOTABLES.
ÉTAPE 9 ÉTAPE 15 REMARQUE : L'assistance d'autrui peut être nécessaire à cette étape. Insérer quatre PETITES VIS D'EXCENTRIQUE (6) dans les trous exacts illustrés dans le DEVANT DE TIROIR (S). Enfoncer treize EXCENTRIQUES ESCAMOTABLES (3) dans les EXTRÉMITÉS (A et B), les MONTANTS (C et D), l'ARRIÈRE (H) et les PANNEAUX AVANT (I et J). Fixer les EXTRÉMITÉS (A et B), les MONTANTS (C et D), l'ARRIÈRE (H) et les PANNEAUX AVANT (I et J) au DESSUS (E). Serrer treize EXCENTRIQUES ESCAMOTABLES.
ÉTAPE 19 ÉTAPE 20 Relever, avec précaution, l'élément dans sa position verticale. Apposer l'ÉTIQUETTE DE MISE EN GARDE (18) au DESSUS (E). Cette étiquette doit pouvoir être lisible lorsque le téléviseur est enlevé de l'élément. Lorsque le téléviseur est en place, il doit la dissimuler. Décoller le film protecteur et apposer l'étiquette comme l'indique le schéma.
419232 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 4 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Inserte dos EXCÉNTRICOS ESCONDIDOS (3) dentro del DORSO (H). • Verifique el tamaño y peso del televisor.
PASO 9 PASO 15 NOTA: Usted puede necesitar la ayuda de alguien para este paso. Atornille cuatro PASADORES DE EXCÉNTRICO PEQUEÑOS (6) dentro de los agujeros correspondientes indicados de la CARA DE CAJÓN (S). Inserte treinta EXCÉNTRICOS ESCONDIDOS (3) dentro de los EXTREMOS (A y B), los PARALES (C y D), el DORSO (H) y los PANELES DELANTEROS (I y J). Fije los EXTREMOS (A y B), los PARALES (C y D) y el DORSO (H) a los PANELES DELANTEROS (I y J) y al PANEL SUPERIOR (E).
PASO 19 PASO 20 Cuidadosamente ponga la unidad en posición vertical. Aplique la ETIQUETA DE ADVERTENCIA (18) al PANEL SUPERIOR (E). La etiqueta debe ser legible cuando el televisor está retirado de la unidad. Con el televisor ya instalado, debe esconder la etiqueta. Quite el material protector y aplique la etiqueta tal como se muestra en el diagrama.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 1-800-445-1527 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
