sauder.com You'll love what we have in storage. Storage Cabinet Cannery Bridge Collection | 419151 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-24 Français pg 25-28 Español pg 29-32 Lot # 376472 09/16/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 1-24 Hammer Français 25-28 Español 29-32 Safety 33-34 Warranty Page 2 Not actual size Skip the power trip. This time. 35 419151 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F HIDDEN CAM - 22 4G METAL BRACKET - 6 7F TWIST-LOCK® FASTENER - 10 14H HINGE - 6 8F 15F WOOD DOWEL - 10 CAM SCREW - 22 53K PULL - 2 5L WARNING LABEL - 1 SAFETY BRACKET - 1 1G 1M FELT DISC CARD - 2 2R RUBBER SLEEVE - 16 WARNING Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over: • Place heaviest items in the lowest drawers.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F) into the large holes in the ENDS (A and B), UPRIGHT (C), and BOTTOM (E). 7F Do not tighten the TWIST-LOCK® FASTENERS in this step. (10 used) 7F E C A B www.sauder.
Step 2 å Push twenty-two HIDDEN CAMS (1F) into the ENDS (A and B), FRONT SKIRT (M), BACK SKIRT (N), SIDE SKIRTS (O), BOTTOM MOLDING (P), and TOP MOLDING (S). Arrow 1F (22 used) A B Arrow 1F Arrow Hole Arrow The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. 1F O N O S P M Arrow 1F Page 6 419151 www.sauder.
Step 3 å å Carefully flip the ENDS (A and B) over. å å NOTE: Do not overtighten the SCREWS. å NOTE: If the MOLDING comes up off of the SCREWS, remove it and slide it on again. Remember: Righty tighty. Lefty loosey. Turn eight BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS. Slide the END MOLDINGS (Q) onto the ENDS (A and B). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS.
Step 4 å Turn twenty-two CAM SCREWS (8F) into the LEGS (I, J, K, and L). å NOTE: Each REAR LEG will use three CAM SCREWS and each FRONT LEG will use eight CAM SCREWS. 8F (22 used in this step) L Each REAR LEG will use three CAM SCREWS. K J I 8F Each FRONT LEG will use eight CAM SCREWS. Page 8 419151 www.sauder.
Step 5 å å Carefully flip the ENDS (A and B) over. å Now, fill the first hole in the ENDS (A and B) 1/4 to 1/2 full with GLUE. Fasten the FRONT LEGS (I and J) to the ENDS (A and B). Tighten eight HIDDEN CAMS. Wipe away the excess GLUE. å Fill the holes in the short edges of the END MOLDINGS (O) 1/4 to 1/2 full with GLUE (54M). Fasten the END MOLDINGS (O) to the FRONT LEGS (I and J). Tighten two HIDDEN CAMS. Wipe away the excess GLUE.
Step 6 å First, fill the holes in the REAR LEGS (K and L) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into the holes in each LEG. Wipe away the excess GLUE. å Now, fill the hole in the short edges of the SIDE SKIRTS (O) 1/4 to 1/2 full with GLUE. Fasten the REAR LEGS (K and L) to the ENDS (A and B) and SIDE SKIRTS (O). Use eight BLACK 2-1/4" FLAT HEAD SCREWS (26S). Tighten two HIDDEN CAMS in the SIDE SKIRTS (O). Wipe away the excess GLUE. Fill the holes 1/4 to 1/2 full with GLUE.
Step 7 å å Fasten the BOTTOM (E) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. Don't worry. It isn't Rome. This can be built in a day. Fasten the UPRIGHT (C) to the BOTTOM (E). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2.
Step 8 å å Fasten six METAL BRACKETS (4G) to the BACK SKIRT (N), BOTTOM MOLDING (P), and TOP MOLDING (S). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). 1S BLACK 9/16" LARGE HEAD SCREW (8 used in this step) NOTE: Be sure the BRACKETS are even with the edges of the MOLDINGS, except the BOTTOM MOLDING (P) where the BRACKET will fasten to the center. 4G å Fasten the BOTTOM MOLDING (P) to the LEFT FRONT LEG (J). Tighten the HIDDEN CAM. å Fasten the BOTTOM MOLDING (P) to the BOTTOM (E).
Step 9 å First, fill the holes in the LEFT REAR LEG (L) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into the hole. Wipe away the excess GLUE. å Now, fill the hole in the short edge of the BACK SKIRT (N) 1/4 to 1/2 full with GLUE. å Fasten the BACK SKIRT (N) to the BOTTOM (E). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). Wipe away the excess GLUE. å NOTE: You will tighten the HIDDEN CAMS in the BACK SKIRT in step 14. Fill the holes 1/4 to 1/2 full with GLUE.
Step 10 å Fasten the BALLAST (T) to the BOTTOM (E). Use two BROWN 1-1/2" FLAT HEAD SCREWS (14S). E Use the lower set of holes. T 14S BROWN 1-1/2" FLAT HEAD SCREW (2 used in this step) Page 14 419151 www.sauder.
Step 11 å First, fill the holes in the LEFT FRONT LEG (J) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into the hole. Wipe away the excess GLUE. å Now, fill the hole in the short edge of the FRONT SKIRT (M) 1/4 to 1/2 full with GLUE. å Fasten the FRONT SKIRT (M) to the LEFT FRONT LEG (J). Tighten the HIDDEN CAM. Wipe away the excess GLUE. Fill the holes 1/4 to 1/2 full with GLUE. ! Caution Inspect the parts thoroughly before assembling.
Step 12 å First, fill the holes in the RIGHT LEGS (I and K) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into the holes in each LEG. Wipe away the excess GLUE. å Now, fill the holes in each SKIRT (M and N) 1/4 to 1/2 full with GLUE. Fasten the RIGHT LEGS (I and K) to the FRONT SKIRT (M), and MOLDINGS (P and S). Tighten three HIDDEN CAMS. Wipe away the excess GLUE. å NOTE: You will tighten the HIDDEN CAMS in the BACK SKIRT (N) in step 14.
Step 13 å Fasten the TOP (D) to the ENDS (A and B) and UPRIGHT (C). Tighten six TWIST-LOCK® FASTENERS. å Fasten the TOP MOLDING (S) to the TOP (D). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). 1S Finished edge BLACK 9/16" LARGE HEAD SCREW (2 used in this step) D S B C A www.sauder.
Step 14 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along the two long edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). å NOTE: Perforations have been provided for access through the BACK. å Tighten four HIDDEN CAMS in the BACK SKIRT (N). Caution Do not stand the unit upright without the BACK fastened.
Step 15 å Fasten the DOOR MOLDINGS (R) to the DOORS (G). Use ten BROWN 1" FLAT HEAD SCREWS (12S). 12S BROWN 1" FLAT HEAD SCREW (10 used in this step) 12S ce fa ur S G ith w e rg la es ol h ce fa ur S ith w e rg la es ol h R G Unfinished surface R www.sauder.
Step 16 å Fasten three HINGES (14H) to each DOOR (G). Use twelve BLACK 1/2" FLAT HEAD SCREWS (11S). If you're doing this to help a friend, don't leave without a bite. 14H G G 14H 11S BLACK 1/2” FLAT HEAD SCREW (12 used in this step) Page 20 419151 www.sauder.
Step 17 å å å Carefully stand your unit upright. Stop Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. Mounting screw Fasten a DOOR (G) to the LEFT END (B) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them.
Step 18 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 19 å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 2-1/4" FLAT HEAD SCREW (26S) into a stud in your wall. 26S BLACK 2-1/4" FLAT HEAD SCREW (1 used in this step) 1G BLACK 9/16" LARGE HEAD SCREW (1 used into the top of your unit) 1S www.sauder.
Step 20 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (H) onto the METAL PINS. å å Push a CAM COVER (12P) onto each HIDDEN CAM. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
419151 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Attention Examiner bien les pièces avant d'assembler. Il est difficile de séparer des pièces une fois encollées. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (7F) dans les gros trous dans les EXTRÉMITÉS (A et B), le MONTANT (C) et le DESSOUS (E).
ÉTAPE 9 (SUITE) ÉTAPE 14 Maintenant, remplir le trou du chant court de la PLINTHE ARRIÈRE (N) de 1/4 à 1/2 pleins de COLLE. Attention Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Fixer la PLINTHE ARRIÈRE (N) au DESSOUS (E). Utiliser deux VIS TÊTE LARGE 14 mm NOIRES (1S). Nettoyer l'excès de COLLE. REMARQUE : Serrer les EXCENTRIQUES ESCAMOTABLES dans la PLINTHE ARRIÈRE à l’étape 14. ÉTAPE 10 Fixer le BALLAST (T) au DESSOUS (E).
ÉTAPE 18 ÉTAPE 19 Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Il est recommandé d'utiliser la CONSOLE DE SÉCURITÉ (1G) pour renforcer la stabilité. Utiliser une VIS TÊTE LARGE 14 mm NOIRE (1S) dans le haut de l'élément et une VIS TÊTE PLATE 57 mm NOIRE (26S) dans un montant du mur. Il faut peut-être ajuster les PORTES. Suivre les indications cidessous pour ajuster.
419151 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Precaución Revise las partes cuidadosamente antes de ensamblar. La separación de las piezas ya pegadas es muy difícil. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (7F) dentro de los agujeros grandes de los EXTREMOS (A y B), del PARAL (C) y del FONDO (E).
PASO 9 PASO 13 Precaución Revise las partes cuidadosamente antes de ensamblar. La separación de las piezas ya pegadas es muy difícil. Fije el PANEL SUPERIOR (D) a los EXTREMOS (A y B) y al PARAL (C). Apriete seis SUJETADORES TWIST-LOCK®. Primero, llene los agujeros de la PATA POSTERIOR IZQUIERDA (L) hasta 1/4 a 1/2 con PEGAMENTO (54M). A continuación, inserte un PASADOR DE MADERA (15F) dentro del agujero. Quite el exceso de PEGAMENTO.
PASO 18 PASO 20 Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Empuje los MANGUITOS DE GOMA (2R) sobre las ESPIGAS DE METAL (1R). Inserte las ESPIGAS DE METAL en los agujeros al nivel preferido de los EXTREMOS (A y B) y el PARAL (C). Coloque los ESTANTES AJUSTABLES (H) sobre las ESPIGAS DE METAL. Las PUERTAS pueden requerir de ajustes. Siga el texto abajo para hacer los ajustes necesarios.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
