sauder.com Lion and witch, not included. Armoire Carson Forge Collection | 419079 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-24 Français pg 25-28 Español pg 29-32 Lot # 385193 10/16/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-24 Hammer Français 25-28 Español 29-32 Safety 33-34 Warranty Page 2 Not actual size Skip the power trip. This time. 35 419079 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1S 3S BLACK 9/16" LARGE HEAD SCREW - 27 GOLD 5/16" FLAT HEAD SCREW - 8 11S BLACK 1/2" FLAT HEAD SCREW - 12 15S SILVER 5/8" MACHINE SCREW - 2 16S BLACK 1-7/8" PAN HEAD SCREW - 1 21S BLACK 1-1/8" MACHINE SCREW - 2 30S BLACK 1-9/16" FLAT HEAD SCREW - 5 78S SILVER 1/2" FLAT HEAD SCREW - 2 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F) into the large holes in the ENDS (A and B). å Repeat this step for the BOTTOM (D) and SHELF (E). Do not tighten the TWIST-LOCK® FASTENERS in this step. 7F (12 used) A B Page 6 419079 www.sauder.
Step 2 å Fasten two ROD HANGERS (7A) to the ENDS (A and B). Use two SILVER 1/2" FLAT HEAD SCREWS (78S). å Tap eight SUPPORT PINS (5R) into the ENDS (A and B). Some assembly (and snacks) required. 78S SILVER 1/2" FLAT HEAD SCREW (2 used in this step) 7A A B 5R www.sauder.
Step 3 å Turn nine CAM SCREWS (8F) into the FEET (I and J), DRAWER FRONT (L), SHELF MOLDING (M), and BOTTOM MOLDING (N). å Push nine HIDDEN CAMS (1F) into the BOTTOM (D), SHELF (E), SKIRT (G), and DRAWER BRACE (M65). L N M J 8F I (9 used) Arrow (9 used) 1F D Arrow E G M65 Hole Arrow The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. 1F Page 8 419079 www.sauder.
Step 4 å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S Finished edge Glide end Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S A 1 2 3 B 3 Finished edge 2 1 Glide end www.sauder.
Step 5 å Fasten the LEFT END (B) to the TOP (C) and SHELF (E). Tighten four TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 6 å Fill the hole in the LEFT END (B) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into this hole. Wipe away the excess GLUE. å å Next, fill the hole in BOTTOM (D) 1/4 to 1/2 full with GLUE (54M). å Fill the hole in the BOTTOM (D) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into this hole. Wipe away the excess GLUE. å å Next, fill the hole in the RIGHT END (A) 1/4 to 1/2 full with GLUE (54M). Fasten the LEFT END (B) to the BOTTOM (D).
Step 7 å Fasten two METAL BRACKETS (4G) to the BOTTOM (D). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). Don't worry. It isn't Rome. This can be built in a day. å Fasten two CORNER BRACKETS (31G) to the ENDS (A and B) and BOTTOM (D). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the BRACKETS are even with the edges of the ENDS (A and B) and BOTTOM (D). 1S BLACK 9/16" LARGE HEAD SCREW (10 used in this step) 31G B A D 4G 31G Page 12 419079 www.sauder.
Step 8 å Fasten the FEET (I and J) to the SKIRT (G). Tighten two HIDDEN CAMS. 1 2 These hole must be here. Flat edge I G ce rfa Su th wi EN DD HI S M CA J Flat edge www.sauder.
Step 9 å Fill the holes in the ENDS (A and B) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into these holes. Wipe away the excess GLUE. å Fill the large holes in the FEET (I and J) 1/4 to 1/2 full with GLUE (54M). Quickly, flip the FEET over and insert the WOOD DOWELS (15F) in the ENDS into the holes in the FEET. Wipe away the excess GLUE. å Fasten the FEET (I and J) to the ENDS (A and B).
Step 10 å Fasten the SHELF MOLDING (M) to the SHELF (E). Tighten three HIDDEN CAMS. å Fill the holes in the BOTTOM MOLDING (N) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into these holes. Wipe away the excess GLUE. å Fill the two outer holes in the BOTTOM (D) 1/4 to 1/2 full with GLUE (54M). å Insert the WOOD DOWELS (15F) in the BOTTOM MOLDING (N) into the holes in the BOTTOM (D). Wipe away the excess GLUE. Fill the holes 1/4 to 1/2 full with GLUE.
Step 11 å å Fasten four METAL BRACKETS (4G) to the TOP MOLDING (K). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the BRACKETS are even with the edge of the TOP MOLDING (K). å Fasten two TIE PLATES (3G) to the TOP MOLDING (K). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å Push two LARGE RUBBER SLEEVES (59G) onto the TIE PLATES (3G). å Fasten the TOP MOLDING (K) to the TOP (C). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the TOP MOLDING and into the TOP.
Step 12 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 1N NOTE: Be sure to tap NAILS into the holes that line up over the SHELF (E).
Step 13 å Fasten three HINGES (13H) to each DOOR (H). Use twelve BLACK 1/2" FLAT HEAD SCREWS (11S). 11S BLACK 1/2" FLAT HEAD SCREW (12 used in this step) 13H H H 13H Page 18 419079 www.sauder.
Step 14 å å Carefully stand your unit upright. å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten a DOOR (H) to the LEFT END (B). Use the screws in the HINGES. å Fasten a PULL (130K) to the DOOR (H). Use a BLACK 1-1/8" MACHINE SCREW (21S). å Repeat this step for the other door. Pro Tip: Lift with your legs.
Step 15 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 16 VIEW THE T-LOCK BOX VIDEO 1 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D132 B36 D132 L D138 L D138 Groove Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. å Insert the DRAWER SIDES (D132 and D138) at an angle into the slot at each end of the DRAWER FRONT (L).
Step 17 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D132 and D138). å NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. å å NOTE: The glides are not intended to rotate. Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D132) and a DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D138). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. Fasten the PULL (131K) to the DRAWER FRONT (L). Use two SILVER 5/8" MACHINE SCREWS (15S).
Step 18 å To insert the drawer into your unit, tip the front of the drawers down and drop the glides on the drawers behind the glides on the unit. Lift the front of the drawers up and slide them into the unit. å Apply the WARNING LABEL (5L) to the DRAWER LEFT SIDE (D138). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram.
Step 19 å To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
419079 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Attention: Examiner bien les pièces avant d'assembler. Il est difficile de séparer des pièces une fois encollées. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (7F) dans les gros trous des EXTRÉMITÉS (A et B). Répéter cette étape pour le DESSOUS (D) et la TABLETTE (E).
ÉTAPE 9 ÉTAPE 11 Attention: Examiner bien les pièces avant d'assembler. Il est difficile de séparer des pièces une fois encollées. Fixer quatre CONSOLES EN MÉTAL (4G) à la MOULURE DE DESSUS (K). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (1S). Remplir les trous dans les EXTRÉMITÉS (A et B) de 1/4 à 1/2 pleins de COLLE (54M). Insérer ensuite une CHEVILLE EN BOIS (15F) dans les trous indiqués. Nettoyer l'excès de COLLE.
ÉTAPE 15 ÉTAPE 18 Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Il faut peut-être ajuster les PORTES. Suivre les indications ci-dessous pour ajuster. Pour insérer le tiroir dans l'élément, abaisser le devant du tiroir et faire passer les roulettes situées sur le tiroir derrière les roulettes situées sur l'élément. Relever les devants du tiroir et les enfiler dans l'élément.
419079 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Precaución: Revise las partes cuidadosamente antes de ensamblar. La separación de las piezas ya pegadas es muy difícil. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (7F) en los agujeros grandes de los EXTREMOS (A y B). Repita este paso para el FONDO (D) y el ESTANTE (E).
PASO 9 PASO 11 Precaución: Revise las partes cuidadosamente antes de ensamblar. La separación de las piezas ya pegadas es muy difícil. Fije cuatro SOPORTES DE METAL (4G) a la MOLDURA DE PANEL SUPERIOR (K). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Llene los agujeros de los EXTREMOS (A y B) hasta 1/4 a 1/2 con PEGAMENTO (54M). A continuación, inserte un PASADOR DE MADERA (15F) dentro de estos agujeros. Quite el exceso de PEGAMENTO.
PASO 14 PASO 17 Cuidadosamente ponga la unidad en posición vertical. Inserte un EXCÉNTRICO DE CORREDERA (10A) dentro de los LADOS DE CAJÓN (D132 y D138). Coloque la VARILLA (P) sobre los SOPORTES DE VARILLA sujetados a los EXTREMOS (A y B). Antes de ajustar la PUERTA en su unidad, asegúrese de que el tornillo de montaje esté contra los topes, tal como se muestra en el diagrama. Si no lo está, afloje el tornillo de montaje para que se deslice contra los topes. Luego apriete el tornillo de montaje.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
