sauder.com Yes, you still have to dress yourself. Dresser Barrister Lane Collection | 418902 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 372701 07/07/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Page 2 Not actual size Skip the power trip. This time. 31 418902 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 35AA UNIVERSAL CABINET RAIL - 12 1F HIDDEN CAM - 16 70K PULL - 8 2F 35AC DRAWER RIGHT - 6 CAM DOWEL - 16 71K KNOB - 8 19F 35AD DRAWER LEFT - 6 MOLDING CONNECTOR - 2 5L WARNING LABEL - 1 10A SLIDE CAM - 12 1G SAFETY BRACKET - 1 4G METAL BRACKET - 11 1N NAIL - 48 1R METAL PIN - 8 WARNING Serious or fatal crushing injuries can occur from furniture tip-over.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), BOTTOM (E), and DRAWER BRACES (M64). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å å Fasten six UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A and B). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Remember: Righty tighty. Lefty loosey. *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Glide end 1 2 3 S HI urfa DD ce EN wi CA th M S 1 2 1 3 3 2 A 2 3 1 S HI urfa DD ce EN wi CA th M S 3 2 3 1 2 B Finished edge 1 Glide end Finished edge Page 6 418902 www.sauder.
Step 3 å Fasten six UNIVERSAL CABINET RAILS* (35AA) to the UPRIGHT (C). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Glide end 1 Edge with CAM DOWELS 2 3 S HI urfa DD ce EN wi CA th M S 1 2 3 1 Finished edge 2 C 3 3 Glide end 1 3 2 3 www.sauder.
Step 4 å Fasten the TOP (D) to the RAILS (Q and R). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S Curved edge BLACK 1-7/8" FLAT HEAD SCREW (8 used in this step) R Q ce fa ur S D ith w er w fe es ol h Page 8 418902 R www.sauder.
Step 5 å Tap two MOLDING CONNECTORS (19F) into the notches in the MOLDINGS (M, N, and O). Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS. Flat end Flat end Unfinished surface 19F 19F Unfinished surface O N M www.sauder.
Step 6 å Fasten the TOP (D) to the MOLDINGS (M, N, and O). Use eight SILVER 1-1/8" FLAT HEAD SCREWS (10S). å NOTE: Do not overtighten the SCREWS into the TOP. 10S SILVER 1-1/8" FLAT HEAD SCREW (8 used in this step) Fi ni sh ed su rfa ce Do not overtighten the SCREWS (10S). O M ed h is n Fi e ac rf su ce fa ur S D ith w Fi ni sh ed es ol h su rfa ce e or m Q N Page 10 418902 www.sauder.
Step 7 å Fasten the UPRIGHT (C) to the BOTTOM (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Finished edge Sur withface HID CA DEN MS These holes must be here. C ith e w AMS c a f Sur DEN C D HI E 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) www.sauder.
Step 8 å Insert eight METAL PINS (1R) into the holes in the ENDS (A and B) and UPRIGHT (C). å å Place the BRACES (G) onto the METAL PINS in the UPRIGHT (C). å NOTE: Be sure the METAL PINS in the ENDS (A and B) insert into the holes in the ends of the BRACES (G). Fasten the ENDS (A and B) to the BOTTOM (E). Tighten four HIDDEN CAMS.
Step 9 å Fasten the TOP (D) to the UPRIGHT (C). Tighten two HIDDEN CAMS. å Fasten the MOLDINGS (N and O) to the ENDS (A and B). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees N M A D C O B www.sauder.
Step 10 å Fasten the BASES (I and J) to the ENDS (A and B). Use four BLACK 1-1/4" FLAT HEAD SCREWS (7S). 7S BLACK 1-1/4" FLAT HEAD SCREW (4 used in this step) I A Flat edge B J Flat edge Page 14 418902 www.sauder.
Step 11 å Fasten eight METAL BRACKETS (4G) to the ENDS (A and B) and BOTTOM (E). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the METAL BRACKETS are even with the edges of the ENDS and BOTTOM. å Fasten the BASE (H) to the ENDS (A and B) and BOTTOM (E). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the BASE. 1S BLACK 9/16" LARGE HEAD SCREW (16 used in this step) Flat edge H A E 4G 4G B 4G www.sauder.
Step 12 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). å Fasten three METAL BRACKETS (4G) to the SUPPORT (P). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the METAL BRACKETS are even with the edge of the SUPPORT.
Step 13 VIEW THE T-LOCK BOX VIDEO 1 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D22 D977 D22 L D23 L D23 Groove å Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Insert the DRAWER SIDES (D22 and D23) at an angle into the slot at each end of the DRAWER FRONT (L).
Step 14 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D22 and D23). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. å å NOTE: The glides are not intended to rotate. Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D22) and a DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D23). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2.
Step 15 å Fasten four KNOBS (71K) to the UPPER DRAWER FRONT (K). Use four BLACK 7/8" MACHINE SCREWS (37S). å Fasten two PULLS (70K) to the DRAWER FRONT (L). Use four BLACK 7/8" MACHINE SCREWS (37S). å Repeat this step for the remaining drawers. 37S BLACK 7/8" MACHINE SCREW (24 used in this step) K 71K L 70K www.sauder.
Step 16 å å Carefully stand your unit upright. We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the underneath surface of the TOP (D) and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. 1G BLACK 1-7/8" FLAT HEAD SCREW (1 used into a stud in your wall) 2S BLACK 9/16" LARGE HEAD SCREW (1 used into your unit) 1S D Page 20 418902 www.sauder.
Step 17 å To insert the drawer into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit. å Apply the WARNING LABEL (5L) to the SMALL DRAWER LEFT SIDE (D27). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram.
Step 18 å To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
418902 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer le MONTANT (C) au DESSOUS (E). Utiliser deux VIS TÊTE PLATE 48 mm NOIRES (2S).
ÉTAPE 12 ÉTAPE 15 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Fixer quatre POIGNÉES (71K) sur le DEVANT DE TIROIR SUPÉRIEUR (K). Utiliser quatre VIS À MÉTAUX 22 mm NOIRES (37S). Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (F) et le placer sur l'élément. Fixer deux POIGNÉES (70K) au DEVANT DE TIROIR (L). Utiliser quatre VIS À MÉTAUX 22 mm NOIRES (37S).
418902 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dieciséis EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), del PARAL (C), del FONDO (E) y de las RIOSTRAS DE CAJÓN (M64).
PASO 12 PASO 15 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije cuatro POMOS (71K) a la CARA DE CAJÓN SUPERIOR (K). Utilice cuatro TORNILLOS NEGROS PARA METAL de 22 mm (37S). Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (F) y colóquelo sobre la unidad. Fije dos TIRADORES (70K) a la CARA DE CAJÓN (L). Utilice cuatro TORNILLOS NEGROS PARA METAL de 22 mm (37S).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from the bottom to the top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones y estantes sobrecargados pueden romperse. • Nunca exceda los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
