sauder.com Finally. A reason to use coasters. 3 Piece Table Set Beginnings Collection | 418874 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-11 Français pg 12-14 Español pg 15-17 Lot # 368918 02/19/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification 3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 2 4-11 Hammer Français 12-14 Español 15-17 Safety 18 Warranty 19 Not actual size Skip the power trip. This time. Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Insert a CONNECTOR SCREW (8S) into each HIDDEN CONNECTOR (5F). 5F 8S Step 2 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Use your hammer to tap eighteen HIDDEN CONNECTORS (5F) with SCREWS into the large holes in the LARGE TABLE LONG BRACES (B). å Repeat this step for the LARGE TABLE SHORT BRACES (C) and SMALL TABLE LONG BRACES (H).
Step 3 å å Fasten the LARGE TABLE LONG BRACES (B) and LARGE TABLE SHORT BRACES (C) to the LARGE TABLE TOP (A). Tighten ten HIDDEN CONNECTORS. Remember: Righty tighty. Lefty loosey. Fasten the LARGE TABLE SHORT BRACES (C) to the LARGE TABLE LONG BRACES (B). Use four SILVER 2" FLAT HEAD SCREWS (57S). How to use the HIDDEN CONNECTOR To fasten two parts together using the HIDDEN CONNECTORS, insert your screwdriver, at an angle, into the slot in the HIDDEN CONNECTOR.
Step 4 å Insert two METAL PINS (1R) into a short edge of the LARGE TABLE SHORT BRACES (C). å Fasten the LARGE TABLE LEGS (E and F) to the SHORT BRACES (C). Use two SILVER 2" FLAT HEAD SCREWS (57S). å NOTE: Be sure the METAL PINS insert into the holes in the TABLE LEGS (E and F). å Fasten the LARGE TABLE LEGS (E and F) to the LARGE TABLE LONG BRACE (B). Use four BLACK 1-1/8" PAN HEAD SCREWS (9S).
Step 5 å Insert a METAL PIN (1R) into a short edge of the LARGE TABLE LEG BRACES (D). å Fasten the LARGE TABLE LEG BRACES (D) to the LARGE TABLE LEGS (E and F). Use two SILVER 2" FLAT HEAD SCREWS (57S). å NOTE: Be sure the PINS in the BRACES insert into the LEGS. Don't worry. It isn't Rome. This can be built in a day. 57S SILVER 2" FLAT HEAD SCREW (2 used in this step) 1R E D 1R F D www.sauder.
Step 6 å Insert a METAL PIN (1R) into the short edges of the LARGE TABLE LEG BRACES (D) and LARGE TABLE SHORT BRACES (C). å Fasten the LARGE TABLE LEGS (E and F) to the LARGE TABLE LONG BRACE (B). Use four BLACK 1-1/8" PAN HEAD SCREWS (9S). å Fasten the LARGE TABLE LEGS (E and F) to the LARGE TABLE SHORT BRACES (C) and LARGE TABLE LEG BRACES (D). Use four SILVER 2" FLAT HEAD SCREWS (57S). å NOTE: Be sure the PIN in the BRACES insert into the LEGS.
Step 7 å å First, fasten two SMALL TABLE LONG BRACES (H) to a SMALL TABLE TOP (G). Tighten four HIDDEN CONNECTORS. å å Insert two METAL PINS (1R) into a short edge of the SMALL TABLE LONG BRACES (H). å å NOTE: Be sure the METAL PINS insert into the holes in the SMALL TABLE LEGS. Second, fasten two SMALL TABLE SHORT BRACES (I) to the SMALL TABLE LONG BRACES (H). Use four SILVER 2" FLAT HEAD SCREWS (57S). Fasten the SMALL TABLE LEGS (K and L) to the SMALL TABLE LONG BRACES (H).
Step 8 å å Insert six METAL PINS (1R) into the short edges of the SMALL TABLE LEG BRACES (J) and SMALL TABLE LONG BRACES (H). å Fasten two additional SMALL TABLE LEGS (K and L) to the SMALL TABLE LEG BRACES (J) and SMALL TABLE LONG BRACES (H). Use four SILVER 2" FLAT HEAD SCREWS (57S). å å NOTE: Be sure the METAL PINS insert into the holes in the SMALL TABLE LEGS. å Repeat steps 7 and 8 to complete the assembly of the remaining small table.
Step 9 å å Carefully stand your units upright. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. Pro Tip: Lift with your legs. And, you know, your arms. Center a SCREW COVER (21P) over the head of each SCREW and press firmly. And to celebrate, why not share your success story? 40 lbs. 21P (36 used) To cover screws 25 lbs. 25 lbs. www.sauder.
418874 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 4 Insérer une VIS DE CONNECTEUR (8S) dans chaque CONNECTEUR ESCAMOTABLE (5F). Insérer deux GOUPILLES EN MÉTAL (1R) dans un chant court des ENTRETOISES COURTES DE GRANDE TABLE (C). ÉTAPE 2 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Utiliser un marteau pour enfoncer dix-huit CONNECTEURS ESCAMOTABLES (5F) avec les VIS dans les gros trous des ENTRETOISES LONGUES DE GRANDE TABLE (B).
ÉTAPE 7 ÉTAPE 8 Commencer par fixer les ENTRETOISES LONGUES DE PETITE TABLE (H) sur un DESSUS DE PETITE TABLE (G). Serrer quatre CONNECTEURS ESCAMOTABLES. Insérer six GOUPILLES EN MÉTAL (1R) dans des chants courts des ENTRETOISES DE PIED DE PETITE TABLE (J) et des ENTRETOISES LONGUES DE PETITE TABLE (H). Ensuite, fixer deux ENTRETOISES COURTES DE PETITE TABLE (I) sur les ENTRETOISES LONGUES DE PETITE TABLE (H). Utiliser quatre VIS ARGENTÉE TÊTE PLATE 50 mm (57S).
418874 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 4 Inserte un TORNILLO CONECTOR (8S) dentro de cada CONECTOR INVISIBLE (5F). Inserte dos ESPIGAS DE METAL (1R) entre el borde corto de las RIOSTRAS CORTAS DE LA MESA GRANDE (C). PASO 2 Fije las PATAS DE LA MESA GRANDE (E y F) a las RIOSTRAS CORTAS (C). Utilice dos TORNILLO PLATEADO DE CABEZA PERDIDA de 50 mm (57S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso.
PASO 7 PASO 8 Primero, fije dos RIOSTRAS LARGAS DE LA MESA PEQUEÑA (H) al PANEL SUPERIOR DE LA MESA PEQUEÑA (G). Apriete cuatro CONECTORES INVISIBLES. Inserte seis ESPIGAS DE METAL (1R) entre los bordes cortos de las RIOSTRAS DE LAS PATAS DE LA MESA PEQUEÑA (J) y de las RIOSTRAS LARGAS DE LA MESA PEQUEÑA (H). Segundo, fije dos RIOSTRAS CORTAS DE LA MESA PEQUEÑA (I) a las RIOSTRAS LARGAS DE LA MESA PEQUEÑA (H). Utilice cuatro TORNILLO PLATEADO DE CABEZA PERDIDA de 50 mm (57S).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves. Place the heavier items on the lower shelves.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
