sauder.com The dresser's not-so-distant cousin. 4 Drawer Chest Barrister Lane Collection | Model 418706 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification 3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification R P C R N M O D26 D182 A E D987 M64 D27 K F F I B F D D22 D183 J G D987 M64 L D23 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 35AA UNIVERSAL CABINET RAIL - 8 10A SLIDE CAM - 8 1F 35AC DRAWER RIGHT - 4 2F HIDDEN CAM - 18 35AD DRAWER LEFT - 4 19F CAM DOWEL - 18 4G METAL BRACKET - 7 70K PULL - 6 71K KNOB - 4 5L WARNING LABEL - 1 13M WASHER - 1 60M MOLDING CONNECTOR - 2 SAFETY STRAP - 1 WARNING Serious or fatal crushing injuries can occur from furniture tip-over.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1S BLACK 9/16" LARGE HEAD SCREW - 15 3S 7S BLACK 1-1/4" FLAT HEAD SCREW - 4 10S SILVER 1-1/8" FLAT HEAD SCREW - 7 14S BROWN 1-1/2" FLAT HEAD SCREW - 7 GOLD 5/16" FLAT HEAD SCREW - 32 30S BLACK 1-9/16" FLAT HEAD SCREW - 20 37S BLACK 7/8" MACHINE SCREW - 16 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push eighteen HIDDEN CAMS (1F) into the ENDS (A and B), BOTTOM (D), BRACES (F), and DRAWER BRACES (M64). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A and B). Use sixteen GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Remember: Righty tighty. Lefty loosey. *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (16 used in this step) Glide end 1 2 3 S HI urfa DD ce EN wi CA th M S 1 2 3 3 1 2 2 A 1 3 S HI urfa DD ce EN wi CA th M S 3 1 2 2 3 1 3 B 2 1 3 2 1 Finished edge Glide end Finished edge www.sauder.
Step 3 å Fasten the TOP (C) to the RAILS (P and R). Use seven BROWN 1-1/2" FLAT HEAD SCREWS (14S). Curved edge 14S BROWN 1-1/2" FLAT HEAD SCREW (7 used in this step) P R ce fa ur S C ith w R er w fe es ol h Page 8 418706 www.sauder.
Step 4 å Tap two MOLDING CONNECTORS (19F) into the notches in the MOLDINGS (M, N, and O). Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS. Flat end Unfinished surface 19F Unfinished surface Flat end 19F Unfinished surface O N M www.sauder.
Step 5 å Fasten the TOP (C) to the MOLDINGS (M, N, and O). Use seven SILVER 1-1/8" FLAT HEAD SCREWS (10S). å NOTE: Do not overtighten the SCREWS into the TOP. 10S SILVER 1-1/8" FLAT HEAD SCREW (7 used in this step) su rfa ce N Fi ni sh ed Do not overtighten the SCREWS (10S). ith w s ce ole fa h ur e S or m C e ac rf su su rfa ce ed h is n Fi O Fi ni sh ed M Long curved edge Page 10 418706 www.sauder.
Step 6 å Fasten the LEFT END (B) to the LEFT MOLDING (O). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Finished edge O M B e fac Sur withDEN HID S M CA Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 7 å å Insert six METAL PINS (1R) into the ends of the BRACES (F). å NOTE: Be sure the METAL PINS in the BRACES insert into the holes in the LEFT END. Maximum 210 degrees Fasten the BRACES (F) to the LEFT END (B). Tighten three HIDDEN CAMS. Arrow Minimum 190 degrees (6 used) 1R F B Sur fac ew ith HID DEN CA MS F F Sur fac ew ith HID DEN CA MS Sur fac ew ith HID DEN CA MS Edge without HIDDEN CAMS Page 12 418706 www.sauder.
Step 8 å Fasten the BOTTOM (D) to the LEFT END (B). Tighten two HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Now might be a good time to refresh your drink. B Sur withface HID CA DEN MS D These holes must be here. www.sauder.
Step 9 å Fasten the RIGHT END (A) to the BOTTOM (D), BRACES (F), and RIGHT MOLDING (N). Tighten seven HIDDEN CAMS. å NOTE: Be sure the METAL PINS in the BRACES insert into the holes in the RIGHT END. Maximum 210 degrees Arrow Minimum 190 degrees Finished edge F F F MS CA N E IDD H t ou with A D e fac Sur Page 14 418706 N www.sauder.
Step 10 å Fasten seven METAL BRACKETS (4G) to the ENDS (A and B) and BOTTOM (D). Use seven BLACK 9/16" LARGE HEAD SCREWS (1S). å å å NOTE: Be sure the edges of the METAL BRACKETS are even with the edges of the ENDS and BOTTOM. Fasten the BASES (I and J) to the ENDS (A and B). Use four BLACK 1-1/4" FLAT HEAD SCREWS (7S). Fasten the BASE (G) to the ENDS (A and B) and BOTTOM (D). Use seven BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the BASE.
Step 11 å Carefully turn your unit over onto its front edges. Unfold the BACK (E) and lay it over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (E) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: A perforation has been provided for access through the BACK for the SAFETY STRAP. Carefully cut out the hole.
Step 12 VIEW THE T-LOCK BOX VIDEO 1 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D22 D987 D22 L L D23 D23 Groove å Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Insert the DRAWER SIDES (D22 and D23) at an angle into the slot at each end of the DRAWER FRONT (L).
Step 13 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D22 and D23). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. å å NOTE: The glides are not intended to rotate. Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D22) and a DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D23). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2.
Step 14 å Fasten the KNOBS (71K) to the UPPER DRAWER FRONT (K). Use four BLACK 7/8" MACHINE SCREWS (37S). å Fasten two PULLS (70K) to the DRAWER FRONT (L). Use four BLACK 7/8" MACHINE SCREWS (37S). å Repeat this step for the remaining drawers. 37S BLACK 7/8" MACHINE SCREW (16 used in this step) K 71K L 70K www.sauder.
Step 15 å å å Carefully stand your unit upright. å INSTALLATION INSTRUCTIONS: (Also available at www.yl-anchors.com) 1. Insert the SAFETY DRYWALL ANCHOR (61M) through the WASHER (13M) and one end of the SAFETY STRAP (60M). 2. Using a Phillips screwdriver or a hand drill, press the screw slightly onto the drywall. 3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips through. 4. Turn the screw until it is flush against the wall and you feel a firm resistance. 5.
Step 16 å To insert the drawer into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit. å Apply the WARNING LABEL (5L) to the SMALL DRAWER LEFT SIDE (D27). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram.
Step 17 å To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
Modèle 418706 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Insérer six GOUPILLES EN MÉTAL (1R) dans les extrémités des ENTRETOISES (F). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer les ENTRETOISES (F) à l'EXTRÉMITÉ GAUCHE (B). Serrer trois EXCENTRIQUES ESCAMOTABLES.
ÉTAPE 12 ÉTAPE 15 (SUITE) 1 Insérer les CÔTÉS DE TIROIR (D22 et D23) en biseau dans la fente dans chaque extrémité du DEVANT DE TIROIR (L). INSTRUCTIONS D’INSTALLATION : (Également disponible à www. yl-anchors.com) 2 Enfiler le FOND DE TIROIR (D987) dans les rainures des CÔTÉS DE TIROIR (D22 et D23) et du DEVANT DE TIROIR (L). 1. Insérer le DISPOSITIF DE SÉCURITÉ POUR PLACOPLÂTRE (61M) à travers la RONDELLE (13M) et une extrémité de la SANGLE DE SÉCURITÉ (60M).
Modelo 418706 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Inserte seis ESPIGAS DE METAL (1R) dentro de los extremos de las RIOSTRAS (F). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dieciocho EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), del FONDO (D), de las RIOSTRAS (F) y de las RIOSTRAS DE CAJÓN (M64).
PASO 12 PASO 15 (CONTINUACIÓN) 1 Inserte los LADOS DE CAJÓN (D22 y D23) en ángulo dentro del encaje en cada extremo de la CARA DE CAJÓN (L). INSTRUCCIONES DE INSTALACIÓN: (También disponible en www.yl-anchors.com) 2 Deslice el FONDO DE CAJÓN (D987) dentro de las ranuras de los LADOS DE CAJÓN (D22 y D23) y de la CARA DE CAJÓN (L). 1. Inserte el ANCLAJE DE SEGURIDAD PARA EL DRYWALL (61M) a través la ARANDELA (13M) y de un extremo de la CORREA DE SEGURIDAD (60M).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
