sauder.com For things 'n such. 3-Drawer Chest Barrister Lane Collection | Model 418702 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 373060 06/19/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Not actual size Français 19-21 Español 22-24 Safety 25-26 Short Screwdriver Tape Measure Warranty 27 Skip the power trip. This time. ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 35AA UNIVERSAL CABINET RAIL - 6 1F HIDDEN CAM - 15 71K KNOB - 12 2F 1L 35AC DRAWER RIGHT - 3 10A SLIDE CAM - 6 35AD DRAWER LEFT - 3 CAM DOWEL - 15 19F MOLDING CONNECTOR - 2 4G METAL BRACKET - 7 WARNING LABEL - 1 1N NAIL - 30 1R METAL PIN - 4 WARNING Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push fifteen HIDDEN CAMS (1F) into the ENDS (A and B), BOTTOM (D), BRACES (F), and DRAWER BRACES (M64). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A and B). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Remember: Righty tighty. Lefty loosey. *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Glide end 1 2 1 S HI urfa DD ce EN wi CA th M S 3 2 1 3 3 2 A 3 2 3 S HI urfa DD ce EN wi CA th M S 1 2 3 1 Finished edge 2 B 1 Glide end Finished edge Page 6 418702 www.sauder.
Step 3 å Tap two MOLDING CONNECTORS (19F) into the notches in the MOLDINGS (K, N, and O). Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS. Flat end Unfinished surface 19F Unfinished surface Flat end 19F Unfinished surface O N K www.sauder.
Step 4 å Fasten the TOP (C) to the MOLDINGS (K, N, and O). Use seven SILVER 1-1/8" FLAT HEAD SCREWS (10S). å NOTE: Do not overtighten the SCREWS into the TOP. 10S SILVER 1-1/8" FLAT HEAD SCREW (7 used in this step) su rfa ce N Fi ni sh ed Do not overtighten the SCREWS (10S). ce les fa o ur h S ith w K e ac rf su su rfa ce O Fi ni sh ed ed h is n Fi C Long curved edge Page 8 418702 www.sauder.
Step 5 å Fasten the RIGHT END (A) to the RIGHT MOLDING (N). Tighten two HIDDEN CAMS. å NOTE: The foam support needs to be at least 1-1/4" thick. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. N A e fac Sur withDEN HID S M CA K O e ac d pl n t, a . or m re p a e p fo h su g es r kin in Fo ac az p ag m Finished edge 1-1/4" thick Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 6 å å Insert four METAL PINS (1R) into the ends of the BRACES (F). å NOTE: Be sure the METAL PINS in the BRACES insert into the holes in the RIGHT END. Maximum 210 degrees Fasten the BRACES (F) to the RIGHT END (A). Tighten two HIDDEN CAMS. Arrow Minimum 190 degrees (4 used) 1R A a Fo m F Sur fac ew ith HID DEN Sur fac CA ew MS ith HID DEN CA MS or p p su t F Edge with HIDDEN CAMS Page 10 418702 www.sauder.
Step 7 å Fasten the BOTTOM (D) to the RIGHT END (A). Tighten two HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees If you're doing this to help a friend, don't leave without a bite. A D Sur fac ew ith HID DEN CA MS These holes must be here. For support, place packing foam and magazines here. www.sauder.
Step 8 å Fasten the LEFT END (B) to the BOTTOM (D), BRACES (F), and LEFT MOLDING (O). Tighten six HIDDEN CAMS. å NOTE: Be sure the METAL PINS in the BRACES insert into the holes in the LEFT END. å NOTE: Use the Short Screwdriver for the HIDDEN CAMS in the BRACES. Maximum 210 degrees Arrow Minimum 190 degrees O D F F B ut itho w e fac Sur S AM C DEN HID Finished edge Page 12 418702 www.sauder.
Step 9 å Fasten seven METAL BRACKETS (4G) to the ENDS (A and B) and BOTTOM (D). Use seven BLACK 9/16" LARGE HEAD SCREWS (1S). å å å NOTE: Be sure the edges of the METAL BRACKETS are even with the edges of the ENDS and BOTTOM. Fasten the BASES (I and J) to the ENDS (A and B). Use four BLACK 1-1/4" FLAT HEAD SCREWS (7S). Fasten the BASE (G) to the ENDS (A and B) and BOTTOM (D). Use seven BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the BASE.
Step 10 å å Unfold the BACK (E) and lay it over your unit. å Fasten the BACK (E) to your unit using the NAILS (1N). Caution Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". Do not stand the unit upright without the BACK fastened. The unit may collapse. 1N NAIL (30 used in this step) E Page 14 418702 www.sauder.
Step 11 VIEW THE T-LOCK BOX VIDEO 1 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D26 D994 D26 H D27 H Groove å D27 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Insert the DRAWER SIDES (D26 and D27) at an angle into the slot at each end of the DRAWER FRONT (H).
Step 12 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D26 and D27). å å å å å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D26) and a DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D27). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. NOTE: The glides are not intended to rotate.
Step 13 å å Carefully stand your unit upright. å Apply the WARNING LABEL (1L) to the TOP (C). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram. å Pro Tip: Lift with your legs. And, you know, your arms. To insert the drawers into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit.
Step 14 å To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
Modèle 418702 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 3 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Enfoncer deux CONNECTEURS DE MOULURE (19F) dans les crans des MOULURES (K, N et O). • Vérifier la taille et le poids du téléviseur.
ÉTAPE 8 ÉTAPE 12 Fixer l'EXTRÉMITÉ GAUCHE (B) au DESSUS (D), aux ENTRETOISES (F) et à la MOULURE GAUCHE (O). Serrer six EXCENTRIQUES ESCAMOTABLES. Insérer une EXCENTRIQUE DE COULISSE (10A) dans les CÔTÉS DE TIROIR (D26 et D27). REMARQUE : S'assurer de bien insérer les GOUPILLES EN MÉTAL situées sur les ENTRETOISES dans les trous dans l'EXTRÉMITÉ GAUCHE. Fixer un TIROIR DROIT (35AC) sur le CÔTÉ DROIT DE TIROIR (D26) et un TIROIR GAUCHE (35AD) sur le CÔTÉ GAUCHE DE TIROIR (D27).
Modelo 418702 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 3 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Ligeramente clave dos CONECTORES DE MOLDURA (19F) dentro de las muescas de las MOLDURAS (K, N y O). • Verifique el tamaño y peso del televisor.
PASO 8 PASO 12 Fije el EXTREMO IZQUIERDO (B) al FONDO (F), a las RIOSTRAS (F) y a la MOLDURA IZQUIERDA (O). Apriete seis EXCÉNTRICOS ESCONDIDOS. Insertar un EXCÉNTRICO DE CORREDERA (10A) en los LADOS DE CAJÓN (D26 y D27). NOTA: Asegúrese de insertar las ESPIGAS DE METAL de las RIOSTRAS dentro de los agujeros del EXTREMO IZQUIERDO. NOTA: Utilice el destornillador corto para los EXCÉNTRICOS ESCONDIDOS en las RIOSTRAS. PASO 9 Fije siete SOPORTES DE METAL (4G) a los EXTREMOS (A y B) y al FONDO (D).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
