sauder.com Store behind closed doors. Storage Cabinet Square1 Collection | 418667 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 370597 04/06/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 418667 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push eight HIDDEN CAMS (1F) into the ENDS (A, B, C, and D). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow 1F (8 used) 2F D C B Arrow A Insert the metal end of the CAM DOWEL into the HIDDEN CAM. www.sauder.
Step 2 å Fasten the UPPER ENDS (A and B) to the TOP (E). Tighten four HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Finished edge Finished edge Su witrface hh ole s B ith e w AMS c a f Sur DEN C D HI Finished edge A Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 3 å Fasten the SHELF (G) to the UPPER ENDS (A and B). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). Some assembly (and snacks) required. Finished edge B A G Su morface re wi ho th les 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 4 å Fasten the LOWER LEFT END (D) to the SHELF (G). Tighten two HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Finished edge G D Page 8 ith e w AMS c a f Sur DEN C HID 418667 www.sauder.
Step 5 å Fasten the BOTTOM (F) to the LOWER LEFT END (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) D Finished edge F These holes must be here. www.sauder.
Step 6 å Fasten the LOWER RIGHT END (C) to the SHELF (G). Tighten two HIDDEN CAMS. å Fasten the LOWER RIGHT END (C) to the BOTTOM (F). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Maximum 210 degrees Arrow Minimum 190 degrees Finished edge G F C ut itho S w e fac AM Sur DEN C HID 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 10 418667 www.sauder.
Step 7 å å NOTE: The BASE (K) has a wood finish and a gray finish. You can position either finish to the front of your unit. Don't worry. It isn't Rome. This can be built in a day. Fasten the BASE (K) to the LOWER ENDS (C and D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). n w ro B h is fin K D y re G h is fin K C 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) www.sauder.
Step 8 å Insert the MAGNETIC CATCHES (2I) into the holes in the TOP (E) and SHELF (G). For adjustments, turn the barrel counter-clockwise. 2I E G Page 12 418667 www.sauder.
Step 9 å Carefully turn your unit over onto its front edges. Unfold one of the BACKS (H) and lay it over the top of your unit. å Make equal margins along all four edges of the BACK (H). Push on opposite corners of your unit if needed to make it "square". å Fasten the sides and upper edge of the BACK (H) to your unit using the NAILS (1N). å NOTE: Do not nail the lower edge of the upper BACK at this time. å Lay the other BACK (H) over the bottom of the unit so it overlaps the upper BACK.
Step 10 å NOTE: The DOOR MOLDINGS (L) have a wood finish and a gray finish. å Fasten the DOORS (I) to the DOOR MOLDINGS (L). Use twelve BROWN 1" FLAT HEAD SCREWS (12S). 12S BROWN 1" FLAT HEAD SCREW (12 used in this step) The holes are closer to this edge. ce fa ur S ith w es ol h L I ce fa ur S L ith w es ol h This surface will be facing the front of the unit. I The holes are closer to this edge.
Step 11 å Fasten four PIVOT HINGES (15H) to the DOORS (I). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the STRIKE PLATES (6I) to the DOOR MOLDINGSS (L). Use four BLACK 1/2" FLAT HEAD SCREWS (11S). 15H L IMPORTANT: Only fasten one PIVOT HINGE to each DOOR in this step. I L 6I I 15H 6I 1S 15H L BLACK 9/16" LARGE HEAD SCREW (4 used for the PIVOT HINGES) I L 6I I 15H 11S BLACK 1/2" FLAT HEAD SCREW (4 used for the STRIKE PLATES) 6I www.sauder.
Step 12 å å Carefully stand your unit upright. å Insert the PIVOT HINGE, which is fastened to the DOOR (I), into the hole in the TOP (E). You will need to tilt your DOOR slightly. å Now, tip the DOOR in and fasten the free PIVOT HINGE to the DOOR. Use a BLACK 9/16" LARGE HEAD SCREW (1S). å NOTE: To make adjustments to the DOOR, loosen the SCREW in the HINGE, make needed adjustments, and tighten the SCREW. å Repeat this step for the remaining DOORS. Pro Tip: Lift with your legs.
Step 13 å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. BLACK 1-7/8" FLAT HEAD SCREW (1 used into a stud in your wall) 2S 1G BLACK 9/16" LARGE HEAD SCREW (1 used into the top of your unit) 1S www.sauder.
Step 14 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A, B, C, and D). Set the ADJUSTABLE SHELVES (J) onto the METAL PINS. å å å å Center a SCREW COVER (20P) over the head of each SCREW in the LOWER ENDS (C and D) and press firmly. Push a CAM COVER (12P) onto each visible HIDDEN CAM. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
418667 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer le DESSOUS (F) à l'EXTRÉMITÉ GAUCHE INFÉRIEURE (D). Utiliser deux VIS TÊTE PLATE 48 mm NOIRES (2S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer huit EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A, B, C et D). Ensuite, insérer l'extrémité en métal de la CHEVILLE D'EXCENTRIQUE (2F) dans chaque EXCENTRIQUE ESCAMOTABLE.
ÉTAPE 9 ÉTAPE 12 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Relever, avec précaution, l'élément dans sa position verticale. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'un des ARRIÈRES (H) et le placer sur la portion supérieure de l'unité. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (H).
418667 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el FONDO (F) al EXTREMO IZQUIERDO INFERIOR (D). Utilice dos TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (2S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje ocho EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A, B, C y D). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (2F) dentro de cada EXCÉNTRICO ESCONDIDO.
PASO 9 PASO 12 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Cuidadosamente ponga la unidad en posición vertical. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble uno de los DORSOS (H) y colóquelo sobre la unidad. Los márgenes a lo largo de los cuatro bordes del DORSO (H) deben estar uniformes. Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla "cuadrada.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
