sauder.com For things 'n such. Anywhere Console Dakota Pass Collection | 418540 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-20 Français pg 21-24 Español pg 25-28 Lot # 371455 04/16/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-20 Hammer Français 21-24 Español 25-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 34E ADJUSTABLE FOOT - 1 1F HIDDEN CAM - 9 MOLDING CONNECTOR - 2 1G SAFETY BRACKET - 1 17F 8F TWIST-LOCK® FASTENER - 10 CAM SCREW - 9 10F WARNING LABEL - 1 35M CARD HOLDER - 4 1L WARNING Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur. The TV and furniture will be unstable and may tip. -The TV must less than 50 lbs.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A and B). å Repeat this step for the UPRIGHT (C) and BOTTOM (E). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F (10 used) B A www.sauder.
Step 2 å Push nine HIDDEN CAMS (1F) into the ENDS (A and B) and TOP (D). Arrow 1F (9 used) D B A Arrow Hole Arrow The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. 1F Page 6 418540 www.sauder.
Step 3 å Turn nine CAM SCREWS (8F) into the FRONT LEGS (H and I) and TOP MOLDING (K). 8F (9 used) I H K www.sauder.
Step 4 å Fasten the BACK LEGS (J) to the ENDS (A and B). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S). Remember: Righty tighty. Lefty loosey. These surfaces should be even. 26S BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S Edge with HIDDEN CAMS A J Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S J B Angled edge Edge with HIDDEN CAMS Page 8 418540 www.sauder.
Step 5 å Fasten the TOP (D) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 6 å Fasten the UPRIGHT (C) to the TOP (D). Tighten two TWIST-LOCK® FASTENERS. Notched edge D ith e w K® c a C f Sur T-LO S IS TW TENER FAS Page 10 C 418540 www.sauder.
Step 7 å Tap two MOLDING CONNECTORS (17F) into the notches in the FRONT LEGS (H and I) and TOP MOLDING (K). Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the FRONT LEGS and TOP MOLDING. Flat end Flat end 17F I 17F H K www.sauder.
Step 8 å NOTE: Be very careful when flipping over the FRONT LEGS and TOP MOLDING to fasten to your unit. å Fasten the FRONT LEGS (H and I) to the ENDS (A and B). Tighten six HIDDEN CAMS. å Fasten the TOP MOLDING (K) to the TOP (D). Tighten three HIDDEN CAMS. 1 2 K I B D H A Page 12 418540 www.sauder.
Step 9 å Slide the BOTTOM MOLDING (L) onto the notched edge of the BOTTOM (E). å *U.S. Patent No. 5,499,886 Almost time to celebrate! With a nap. t ou th ® wi K ce OC rfa T-L RS Su IS ENE TW ST FA Notched edge E Slide the BOTTOM MOLDING (L) onto the notched edge. L Groove www.sauder.
Step 10 å Fasten the BOTTOM (E) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. å NOTE: The BOTTOM will be fastened to the UPRIGHT in the next step. B Sur f TW ace wi IS th FAS T-LO TEN CK® ERS L E A Page 14 418540 www.sauder.
Step 11 å Fasten the ADJUSTABLE FOOT (34E) to the BOTTOM (E). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Adjustments to the ADJUSTABLE FOOT will be made once your unit is standing upright. å Fasten the BOTTOM (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREW (2S). å NOTE: One of the SCREWS for the BOTTOM will go through the ADJUSTABLE FOOT and into the UPRIGHT. å Fasten two CARD HOLDERS (35M) to the BOTTOM MOLDING (L). Use four SILVER 1/2" MACHINE SCREWS (38S).
Step 12 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHT (C).
Step 13 å Carefully stand your unit upright and position the unit in its final location. å Turn the ADJUSTABLE FOOT (34E) downward until it touches the floor. å IMPORTANT: The ADJUSTABLE FOOT should not extend beyond the bottom edges of the LEGS (H, I, and J). Pro Tip: Lift with your legs. And, you know, your arms. With your No. 2 Phillips Screwdriver, turn the ADJUSTABLE FOOT downward until it touches the floor. Floor 34E J www.sauder.
Step 14 å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. å Apply the WARNING LABEL (1L) to the TOP (D). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram.
Step 15 å å Slide an ADJUSTABLE SHELF MOLDING* (M) onto the notched edge of the ADJUSTABLE SHELF (G). å å Repeat this step for the other ADJUSTABLE SHELF (G). Then, fasten a CARD HOLDER (35M) to the ADJUSTABLE SHELF MOLDING (M). Use two SILVER 1/2" MACHINE SCREWS (38S). *U.S. Patent No. 5,499,886 G Notched edge These surfaces should be even. M Slide the ADJUSTABLE SHELF MOLDING (M) onto the notched edge. G M Groove Open end 38S SILVER 1/2" MACHINE SCREW (4 used in this step) www.sauder.
Step 16 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (G) onto the METAL PINS. å å å å å Separate a CARD from the CARD SHEET (38M) and insert into each CARD HOLDER. Push a CAM COVER (13P) onto each visible HIDDEN CAM in the ENDS (A and B). Insert the HOLE PLUG (41P) into the hole in the BOTTOM (E).
418540 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 3 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Faire tourner neuf VIS D'EXCENTRIQUE (8F) dans les PIEDS AVANT (H et I) et la MOULURE DE DESSUS (K). • Vérifier la taille et le poids du téléviseur.
ÉTAPE 8 ÉTAPE 11 REMARQUE : Faire attention en retourner les PIEDS AVANT et la MOULURE DE DESSUS pour fixer à l'élément. Fixer le PIED RÉGLABLE (34E) au DESSOUS (E). Utiliser trois VIS TÊTE LARGE 14 mm NOIRES (1S). Fixer les PIEDS AVANT (H et I) aux EXTRÉMITÉS (A et B). Serrer six EXCENTRIQUES ESCAMOTABLES. REMARQUE : Les réglages des PIEDS RÉGLABLES se feront une fois l’unité en position verticale. Fixer la MOULURE DE DESSUS (K) au DESSUS (D). Serrer trois EXCENTRIQUES ESCAMOTABLES.
ÉTAPE 13 ÉTAPE 15 Relever, avec précaution, l'élément dans sa position verticale et placer l'élément dans son emplacement final. Enfiler la MOULURE DE TABLETTE RÉGLABLE* (M) sur le chant cranté de la TABLETTE RÉGLABLE (G). Tourner le PIED RÉGLABLE (34E) vers le bas jusqu'à ce qu'il touche le sol. Ensuite, fixer une PORTE-CARTES (35M) sur la MOULURE DE TABLETTE RÉGLABLE (M). Utiliser deux VIS À MÉTAUX 13 mm ARGENTÉES (38S).
418540 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 3 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Atornille nueve BIELAS DE EXCÉNTRICO (8F) dentro de las PATAS DELANTERAS (H e I) y da la MOLDURA DE PANEL SUPERIOR (K). • Verifique el tamaño y peso del televisor.
PASO 8 PASO 11 NOTA: Tenga cuidado cuando vuelta las PATAS DELANTERAS y la MOLDURA DE PANEL SUPERIOR para fijar a la unidad. Fije la PATA AJUSTABLE (34E) al FONDO (E). Utilice tres TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Fije las PATAS DELANTERAS (H e I) a los EXTREMOS (A y B). Apriete seis EXCÉNTRICOS ESCONDIDOS. NOTA: Los ajustes a las PATAS AJUSTABLES se realizarán una vez que su unidad está en posición vertical. Fije la MOLDURA DE PANEL SUPERIOR (K) al PANEL SUPERIOR (D).
PASO 13 PASO 15 Cuidadosamente ponga la unidad en posición vertical y coloque su unidad en su posición final. Deslice una MOLDURA DE ESTANTE AJUSTABLE* (M) sobre el borde con muesca de cada ESTANTE AJUSTABLE (G). Gire la PATA AJUSTABLE (34E) hacia abajo hasta que toque el piso. A continuación, fije el PORTA-TARJETAS (35M) a la MOLDURA DEL ESTANTE AJUSTABLE (M). Utilice dos TORNILLOS PLATEADOS PARA METAL de 13 mm (38S).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
