sauder.com For all your newfangled gadgetry. Computer Desk Barrister Lane Collection | 418294 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-32 Français pg 33-36 Español pg 37-40 Lot # 366519 11/24/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-32 Hammer Français 33-36 Español 37-40 Safety 41-42 Warranty Not actual size Electric drill with 1/4" bit (ONLY in indicated step) 43 Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification G R K F J U V A O M I E H D W U N O D216 D464 C B T D713 O D216 D464 P O D463 S D102 D713 D463 L D102 Q www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push eighteen HIDDEN CAMS (1F) into the ENDS (A, B, and C), UPRIGHTS (D and E), BOTTOM (H), and UPPER SHELF (J). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. STOP If you purchased the 418295 Hutch, assemble that unit first. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Separate the EXTENSION SLIDES (Y) from the EXTENSION RAILS (X) as shown in the enlarged diagram below. Be prepared, the parts are greasy. Remember: Righty tighty. Lefty loosey. å Fasten the EXTENSION RAILS (X) to the RIGHT END (A) and UPRIGHT (D). Use four GOLD 5/16” FLAT HEAD SCREWS (3S). å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram.
Step 3 å Fasten the CABINET RIGHT (40CA) to the RIGHT END (A) and CABINET LEFT (40CB) to the UPRIGHT (D). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Roller end 1 2 3 Notched edge 4 S HI urfa DD ce EN wi CA th M S A 4 3 Roller end 2 1 S HI urfa DD ce EN wi CA th M S D 3S Finished edge www.sauder.
Step 4 å Fasten the SIDE SKIRTS (O) to the RIGHT END (A), LEFT ENDS (B and C), and LEFT UPRIGHT (E). Use eight BROWN 1" FLAT HEAD SCREWS (12S). 12S BROWN 1" FLAT HEAD SCREW (8 used in this step) S HI urfa DD ce EN wi CA th M S A B S HI urfa DD ce EN wi CA th M S O S HI urfa DD ce EN wi CA tho M ut S C O Unfinished edge S HI urfa DD ce EN wi CA tho M ut S E O O Unfinished edge Page 8 418294 www.sauder.
Step 5 å Fasten the INNER LEFT END (C) to the MODESTY PANEL (I). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. O 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) C Sur HIDface w DEN ith CA MS I Notch www.sauder.
Step 6 å IMPORTANT: If you purchased the 418295 Hutch, you will need to finish drilling through the three partially drilled holes in the TOP (G) using your drill and 1/4" drill bit. 12S BROWN 1" FLAT HEAD SCREW (5 used for the TOP MOLDING) å Fasten the TOP MOLDING (R) to the TOP (G). Use five BROWN 1" FLAT HEAD SCREWS (12S). å To fasten the TOP (G) to the 418295 Hutch, use three BLACK 1-7/8" FLAT HEAD SCREWS (2S) through the TOP and into the Hutch Ends and Upright.
Step 7 å Fasten the OUTER LEFT END (B) to the TOP (G). Tighten two HIDDEN CAMS. R MS CA N E IDD H h it ew c a f Sur B Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 8 å Fasten the INNER LEFT END (C) assembly to the TOP (G). Tighten two HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees G S AM C DEN HID C ith ew c a f Sur I For support, place packing foam and magazines here. Page 12 418294 www.sauder.
Step 9 å Fasten the LEFT UPRIGHT (E) to the TOP (G). Tighten two HIDDEN CAMS. å Fasten the LEFT UPRIGHT (E) to the MODESTY PANEL (I). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Maximum 210 degrees Arrow Minimum 190 degrees Notched edge I G E ut itho S w e fac AM Sur DEN C HID 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) www.sauder.
Step 10 å NOTE: Separate the LEFT END MOLDINGS (T and W). The LEFT FRONT END MOLDING (T) is shorter than the LEFT REAR END MOLDING (W). Do not confuse these MOLDINGS. å Slide the LEFT FRONT END MOLDING (T) onto the notched edges of the LEFT ENDS (B and C). å *U.S. Patent No. 5,499,886 B Notched edges Slide the LEFT FRONT END MOLDING (T) onto the notched edges. C T Page 14 418294 www.sauder.
Step 11 å Slide the PLINTH (S) onto the notched edges of the LEFT ENDS (B and C). å Push a DOOR STOP (4I) into the hole in the LEFT UPRIGHT (E). å *U.S. Patent No. 5,499,886 B Finished edge S C E Slide the PLINTH (S) onto the notched edges. 4I www.sauder.
Step 12 å å å å Insert four METAL PINS (1R) into the SMALL UPRIGHT (F). Insert the METAL PINS (1R) in one end of the SMALL UPRIGHT (F) into the holes in the TOP (G). Fasten the UPPER SHELF (J) to the LEFT UPRIGHT (E). Tighten two HIDDEN CAMS. NOTE: Be sure the METAL PINS in the SMALL UPRIGHT insert into the holes in the UPPER SHELF. Finished edge G F Maximum 210 degrees Arrow Minimum 190 degrees 1R (4 used) Notched edge E Page 16 Sur J HIDface w DEN ith CA MS 418294 www.sauder.
Step 13 å Slide the RIGHT UPRIGHT END MOLDING (U) onto the notched edge of the LEFT UPRIGHT (E). å *U.S. Patent No. 5,499,886 U E Slide the RIGHT UPRIGHT END MOLDING (U) onto the notched edge. www.sauder.
Step 14 å Fasten the UPRIGHT (D) to the UPPER SHELF (J). Tighten two HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day. Finished edge J D ith e w AMS c a f Sur DEN C HID Maximum 210 degrees Arrow Minimum 190 degrees Page 18 418294 www.sauder.
Step 15 å Slide the SHELF MOLDING (V) onto the notched edge of the UPPER SHELF (J). å *U.S. Patent No. 5,499,886 Notched edge V J Slide the SHELF MOLDING (V) onto the notched edge. www.sauder.
Step 16 å Fasten the BOTTOM (H) to the LEFT UPRIGHT (E). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (H) to the UPRIGHT (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). This hole must be here. E D H Sur HIDface w DEN ith CA MS Maximum 210 degrees 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 20 Arrow Minimum 190 degrees 418294 www.sauder.
Step 17 å Fasten the RIGHT END (A) to the TOP (G), BOTTOM (H), and UPPER SHELF (J). Tighten six HIDDEN CAMS. å Slide the RIGHT UPRIGHT END MOLDING (U) onto the notched edge of the RIGHT END (A). å *U.S. Patent No. 5,499,886 Maximum 210 degrees Arrow Minimum 190 degrees Notched edge G J H U A ut itho S w e fac AM Sur DEN C HID Slide the RIGHT UPRIGHT END MOLDING (U) onto the notched edge. www.sauder.
Step 18 å Fasten three METAL BRACKETS (4G) to the RIGHT END (A), LEFT UPRIGHT (E), and BOTTOM (H). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the BRACKETS are even with the edges of the RIGHT END, LEFT UPRIGHT, and BOTTOM. å Fasten the BASE (N) to the RIGHT END (A), LEFT UPRIGHT (E), and BOTTOM (H). Use three BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the RIGHT END, LEFT UPRIGHT, and BOTTOM and into the BASE.
Step 19 å å å Carefully turn your unit over onto its front edges. Unfold the BACK (K) and lay it over your unit. å å å å å Fasten the BACK (K) to your unit using the NAILS (1N). Make equal margins along all four edges of the BACK (K). Push on opposite corners of your unit if needed to make it "square". NOTE: If the 418295 Hutch is attached to your Desk, the BACK (K) will overlap the Hutch Right Back (F) and the corner will tuck underneath the Hutch Left Back (G).
Step 20 å Fasten two HINGES (40H) to the DOOR (L). Use four BLACK 1/2" FLAT HEAD SCREWS (11S). L 11S BLACK 1/2” FLAT HEAD SCREW (4 used in this step) 40H Page 24 418294 www.sauder.
Step 21 å å Carefully stand your unit upright. å Fasten the DOOR (L) to the UPRIGHT (D) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. å Fasten a KNOB (69K) to the DOOR (L). Use a BLACK 1-1/8" MACHINE SCREW (21S). å See the next step for DOOR adjustments. Pro Tip: Lift with your legs. And, you know, your arms.
Step 22 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 23 å Fasten a LARGE DRAWER BOX FRONT (D463) to the LARGE DRAWER SIDES (D102). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). å Slide a DRAWER BOTTOM (D713) into the grooves in the LARGE DRAWER SIDES (D102) and LARGE DRAWER BOX FRONT (D463) å Fasten the other LARGE DRAWER BOX FRONT (D463) to the LARGE DRAWER SIDES (D102). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). å Repeat this step for the other drawer using the DRAWER SIDES (D216) and DRAWER BOX FRONTS (D464).
Step 24 å Fasten the LARGE DRAWER FRONT (Q) to a LARGE DRAWER BOX FRONT (D463). Use four BLACK 7/8" LARGE HEAD SCREWS (17S). å Repeat this step for the other drawer using DRAWER FRONT (P). This drawer will use only two BLACK 7/8" LARGE HEAD SCREWS (17S). 17S BLACK 7/8" LARGE HEAD SCREW (6 used in this step) D463 Q Page 28 418294 www.sauder.
Step 25 å Fasten the EXTENSION SLIDES (Y) to the LARGE DRAWER SIDES (D102). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Open end 1 Y 3 2 D102 D102 Open end 1 Y 3 2 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 26 å Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD) to the DRAWER SIDES (D216). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #2 and #4. Roller end 1 2 4 3 D216 Roller end D216 1 2 4 3 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 30 418294 www.sauder.
Step 27 å Fasten a PULL (70K) to the DRAWER FRONT (P). Use two SILVER 1-1/2" MACHINE SCREWS (95S) through the DRAWER BOX FRONT, through the DRAWER FRONT, and into the PULL. å å å å Fasten a PULL (70K) to the LARGE DRAWER FRONT (Q). Use two GOLD 1" MACHINE SCREWS (50S). Push a FILE GLIDE (3B) onto the right LARGE DRAWER SIDE (D102). Slide the FILE RODS (8B) into the FILE GLIDE (3B) on the right LARGE DRAWER SIDE.
Step 28 å Push the RUBBER SLEEVES (2R) over the remaining METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the UPRIGHTS (D and E). Set the ADJUSTABLE SHELF (M) onto the METAL PINS. å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit.
418294 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. IMPORTANT : Si on a fait l’achat du Surmeuble 418295, finir de percer complètement les trois trous partiellement percés dans le DESSUS (G) à l'aide d'une perceuse et d'un foret de 6 mm. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol.
ÉTAPE 11 ÉTAPE 17 Enfiler la PLINTHE (S) sur les chants crantés des EXTRÉMITÉS GAUCHES (B et C). Fixer l'EXTRÉMITÉ DROITE (A) au DESSUS (G), DESSOUS (H) et à la TABLETTE SUPÉRIEURE (J). Serrer six EXCENTRIQUES ESCAMOTABLES. Enfoncer un ARRÊT DE PORTE (4I) dans le trou du MONTANT GAUCHE (E). * Brevet État Unis n° 5,499,886 Enfiler la MOULURE D'EXTRÉMITÉ DE MONTANT DROIT (U) sur le chant cranté de l'EXTRÉMITÉ DROITE (A).
ÉTAPE 21 ÉTAPE 25 Relever, avec précaution, l'élément dans sa position verticale. Fixer les COULISSES D’EXTENSION (Y) aux CÔTÉS DE GRAND TIROIR (D102). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 3. Avant de fixer la PORTE à l’unité, s’assurer que la vis de montage se trouve contre les butées comme l’indique le schéma de droite. Si ce n’est pas le cas, desserrer la vis de montage pour la faire glisser contre les butées. Serrer ensuite la vis de montage.
418294 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. IMPORTANTE: Si usted compró el Organizador 418295, termine de taladrar completamente los tres agujeros parcialmente perforados en el PANEL SUPERIOR (G) con un taladro y una broca de 6 mm. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dieciocho EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A, B y C), los PARALES (D y E), el FONDO (H) y el ESTANTE SUPERIOR (J).
PASO 11 PASO 17 Deslice la BASE (S) sobre los bordes con muesca de los EXTREMOS IZQUIERDOS (B y C). Fije el EXTREMO DERECHO (A) al PANEL SUPERIOR (G), al FONDO (H) y al ESTANTE SUPERIOR (J). Apriete seis EXCÉNTRICOS ESCONDIDOS. Empuje un TOPE DE PUERTA (4I) en el agujero en el PARAL IZQUIERDO (E). *Patente EE. UU. No. 5,499,886 PASO 12 Inserte cuatro ESPIGAS DE METAL (1R) dentro del PARAL PEQUEÑO (F).
PASO 21 PASO 25 Cuidadosamente ponga la unidad en posición vertical. Fije las CORREDERAS DE EXTENSIÓN (Y) a los LADOS DE CAJÓN GRANDE (D102). Utilice cuatro TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 3. Antes de ajustar la PUERTA a su unidad, asegúrese de que el tornillo de montaje se encuentre contra los topes como se muestra en el diagrama derecho. Si no lo está, afloje el tornillo de montaje para que se deslice contra los topes.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados. • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
