sauder.com Designed for distractions. Anywhere Console Dakota Pass Collection | 418232 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-31 Français pg 32-35 Español pg 36-39 Lot # 367505 03/17/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-31 Hammer Français 32-35 Español 36-39 Safety 40-42 Warranty Not actual size Skip the power trip. This time. 43 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1S BLACK 9/16" LARGE HEAD SCREW - 5 2S 3S GOLD 5/16" FLAT HEAD SCREW - 16 23S SILVER 5/8" FLAT HEAD SCREW - 4 BLACK 1-7/8" FLAT HEAD SCREW - 8 26S BLACK 2-1/4" FLAT HEAD SCREW - 6 30S BLACK 1-9/16" FLAT HEAD SCREW - 5 31S BLACK 7/8" FLAT HEAD SCREW - 6 50S GOLD 1" MACHINE SCREW - 6 102S SILVER 1" LARGE HEAD SCREW - 12 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F) into the large holes in the ENDS (A and B), BOTTOM (D), and BRACE (R). Do not tighten the TWIST-LOCK® FASTENERS in this step. 7F R D B 7F A Page 6 418232 www.sauder.
Step 2 å Turn ten CAM SCREWS (8F) into the DRAWER FRONT (K), FRONT LEGS (L and M), and TOP MOLDING (O). å Push ten HIDDEN CAMS (1F) into the ENDS (A and B), TOP (C), and DRAWER BRACE (M67). M L O K 8F (10 used) Arrow 1F (10 used) C M67 B A Arrow Arrow Hole 1F The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. www.sauder.
Step 3 å Separate the EXTENSION SLIDES (V) from the EXTENSION RAILS (U) as shown in the enlarged diagram below. Be prepared, the parts are greasy. Remember: Righty tighty. Lefty loosey. å Fasten the EXTENSION RAILS (U) to the ENDS (A and B). Use four GOLD 5/16” FLAT HEAD SCREWS (3S). å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END.
Step 4 å Fasten a CABINET RIGHT (35GA) to the RIGHT END (A) and a CABINET LEFT (35GB) to the LEFT END (B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. 3S Edge with HIDDEN CAMS GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Roller end A S HI urfa DD ce EN wi CA th M S 1 2 3 S HI urfa DD ce EN wi CA th M S B 3 2 1 Roller end Edge with HIDDEN CAMS www.sauder.
Step 5 å Fasten the REAR LEGS (N) to the ENDS (A and B). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S). These surfaces should be even. Edge with HIDDEN CAMS These surfaces should be even. S HI urfa DD ce EN wi CA th M S A N N S HI urfa DD ce EN wi CA th M S B Angled edge Edge with HIDDEN CAMS 26S BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) Page 10 418232 www.sauder.
Step 6 å Insert two SMALL WOOD DOWELS (26F) into the BRACE (R). å Fasten the BRACE (R) to the ENDS (A and B). Tighten one TWIST-LOCK® FASTENER. å NOTE: Be sure to tighten only one of the TWIST-LOCK® FASTENERS at this time. Be sure the SMALL WOOD DOWELS in the BRACE insert into the holes in the ENDS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1.
Step 7 å Fasten the TOP (C) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. Edge with HIDDEN CAMS Sur C fac ew ith HID DEN CA MS B A Page 12 418232 www.sauder.
Step 8 å Slide the SHELF MOLDING* (Q) onto the notched edge of the BRACE (R). å *U.S. Patent No. 5,499,886 Notched edge Slide the SHELF MOLDING (Q) onto the notched edge. R Q www.sauder.
Step 9 å Tap two MOLDING CONNECTORS (17F) into the notches in the LEGS (L and M) and TOP MOLDING (O). Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS. Flat end Flat end 17F M 17F L O Page 14 418232 www.sauder.
Step 10 å å Insert two WOOD DOWELS (15F) into the LEGS (L and M). å Fasten the LEGS (L and M) and TOP MOLDING (O) to the ENDS (A and B) and TOP (C). Tighten nine HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the LEGS insert into the holes in the ENDS. NOTE: Be very careful when flipping over the FRONT LEGS and TOP MOLDING to fasten to your unit. 1 2 M O C L B A 15F www.sauder.
Step 11 å Slide the BOTTOM MOLDING* (P) onto the notched edge of the BOTTOM (D). å *U.S. Patent No. 5,499,886 Notched edge Slide the BOTTOM MOLDING (P) onto the notched edge. ce rfa Su th wi RS NE TE AS ®F CK LO TIS TW D Page 16 418232 P www.sauder.
Step 12 å Fasten the BOTTOM (D) to the ENDS (A and B). Tighten four TWIST-LOCK® FASTENERS. å NOTE: You will need to carefully pull the ENDS slightly apart to insert the BOTTOM. å Now, completely tighten the TWIST-LOCK® FASTENER in the BRACE (R) at this time. B R P Sur fac ew ith T www.sauder.
Step 13 å å å å Carefully turn your unit over onto its front edges. å NOTE: Adjustments will be made to the ADJUSTABLE FOOT after the unit is standing upright and in its final location. Don't worry. It isn't Rome. This can be built in a day. Insert three CORD CLIPS (9P) into the holes in the TOP (C). NOTE: The CORD CLIPS are used to manage your cords. Fasten the ADJUSTABLE FOOT (34E) to the BOTTOM (D). Use four SILVER 5/8" FLAT HEAD SCREWS (23S).
Step 14 å å Unfold the BACK (I) and lay it over your unit. å å Fasten the BACK (I) to your unit using the NAILS (1N). Caution Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it "square". Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. 1N NAIL (36 used in this step) I www.sauder.
Step 15 å Insert the peg in the small piece of the DRAWER BRACKET SET (55G) into the hole in the large piece. Then, fasten the DRAWER BRACKETS to the ROLL-OUT ENDS (E and F). Use six BLACK 7/8" FLAT HEAD SCREWS (31S). å NOTE: Be sure to position the DRAWER BRACKET SETS exactly as shown. 31S 55G 31S BLACK 7/8" FLAT HEAD SCREW (6 used in this step) Hole Peg 55G F 55G 55G Page 20 418232 E www.sauder.
Step 16 å Fasten the ROLL-OUT ENDS (E and F) to the ROLL-OUT BOTTOM (G) and ROLL-OUT BACK (H). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (2S). These surfaces should be the same finish as the ROLL-OUT END. F H G Finished edge E 2S BLACK 1-7/8" FLAT HEAD SCREW (8 used in this step) www.sauder.
Step 17 å Fasten the EXTENSION SLIDES (V) to the ROLL-OUT ENDS (E and F). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Open end 1 V 3 2 F Open end E V 3 1 2 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 22 418232 www.sauder.
Step 18 å Fasten the FLIP-UP DOOR (J) to the ROLL-OUT ENDS (E and F). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the DRAWER BRACKETS on the ROLL-OUT ENDS. å Peel the FELT DISC from the FELT DISC CARD (1M) and stick them on the ROLL-OUT ENDS (E and F) where they come in contact with the FLIP-UP DOOR (J).
Step 19 å Fasten two DRAWER FRONT MOLDINGS (S) to the FLIP-UP DOOR (J). Use six SILVER 1" LARGE HEAD SCREWS (102S). å Fasten three KNOBS (28K) to the FLIP-UP DOOR (J). Use three GOLD 1" MACHINE SCREWS (50S). 102S SILVER 1" LARGE HEAD SCREW (6 used in this step) J S S 28K 50S GOLD 1" MACHINE SCREW (3 used for the KNOBS) Page 24 418232 www.sauder.
Step 20 VIEW THE T-LOCK BOX VIDEO The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 1 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D12 D955 D12 K K D13 Groove å D13 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Insert the DRAWER SIDES (D12 and D13) at an angle into the slot at each end of the DRAWER FRONT (K).
Step 21 å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D12 and D13). å Fasten a DRAWER RIGHT (35GC) to the DRAWER RIGHT SIDE (D12) and a DRAWER LEFT (35GD) to the DRAWER LEFT SIDE (D13). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE.
Step 22 å Fasten two DRAWER FRONT MOLDINGS (S) to the DRAWER FRONT (K). Use six SILVER 1" LARGE HEAD SCREWS (102S). å Fasten three KNOBS (28K) to the DRAWER FRONT (K). Use three GOLD 1" MACHINE SCREWS (50S). 102S SILVER 1" LARGE HEAD SCREW (6 used in this step) K S S 28K 50S GOLD 1" MACHINE SCREW (3 used for the KNOBS) www.sauder.
Step 23 å å å Carefully stand your unit upright. å IMPORTANT: The ADJUSTABLE FOOT should not extend beyond the bottom edges of the FRONT LEGS (L and M). Pro Tip: Lift with your legs. And, you know, your arms. Position your unit in its final location. Using your screwdriver through the hole in the BOTTOM (D), turn the ADJUSTABLE FOOT (34E) downward until the FOOT touches the floor. M L D With your No. 2 Phillips Screwdriver, turn the ADJUSTABLE FOOT downward until the FOOT touches the floor.
Step 24 å å We recommend using the SAFETY STRAP (60M) for added stability. å INSTALLATION INSTRUCTIONS: (Also available at www.yl-anchors.com) 1. Insert the SAFETY DRYWALL ANCHOR (61M) through the WASHER (13M) and one end of the SAFETY STRAP (60M). 2. Using a Phillips screwdriver or a hand drill, press screw slightly onto the drywall. 3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips through. 4.
Step 25 å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. å To insert the Roll-out drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier.
Step 26 å To make adjustments to the drawer, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawer this way, it will help the DRAWER FRONT line up better when closed. Tighten the SCREW when finished with adjustments.
418232 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. • Vérifier la taille et le poids du téléviseur.
ÉTAPE 10 ÉTAPE 15 Insérer deux CHEVILLES EN BOIS (15F) dans les PIEDS (L et M). REMARQUE : Faire attention en retourner les PIEDS AVANT et la MOULURE DE DESSUS pour fixer à l'élément. Fixer les PIEDS (L et M) à la MOULURE DE DESSUS (O) aux EXTRÉMITÉS (A et B) et au DESSUS (C). Serrer neuf EXCENTRIQUES ESCAMOTABLES. REMARQUE : S'assurer de bien insérer les CHEVILLES EN BOIS situées sur les PIEDS dans les trous dans les EXTRÉMITÉS.
ÉTAPE 21 ÉTAPE 24 (SUITE) Insérer une EXCENTRIQUE DE COULISSE (10A) dans les CÔTÉS DE TIROIR (D12 et D13). Fixer un TIROIR DROIT (35GC) sur le CÔTÉ DROIT DE TIROIR (D12) et un TIROIR GAUCHE (35GD) sur le CÔTÉ GAUCHE DE TIROIR (D13). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 3. REMARQUE : La tête de vis dans l'EXCENTRIQUE doit être visible à travers le trou fendu dans la COULISSE.
418232 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 4 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. • Verifique el tamaño y peso del televisor.
PASO 10 PASO 15 Introduzca dos PASADORES DE MADERA (15F) en las PATAS (L y M). NOTA: Tenga cuidado cuando vuelta las PATAS DELANTERAS y la MOLDURA DE PANEL SUPERIOR para fijar a la unidad. Fije las PATAS (L y M) y la MOLDURA DE PANEL SUPERIOR (O) a los EXTREMOS (A y B) y al PANEL SUPERIOR (C). Apriete nueve EXCÉNTRICOS ESCONDIDOS. NOTA: Asegúrese de insertar los PASADORES DE MADERA sujetados a las PATAS en los agujeros de los EXTREMOS.
PASO 21 PASO 24 (CONTINUACIÓN) Insertar un EXCÉNTRICO DE CORREDERA (10A) en los LADOS DE CAJÓN (D12 y D13). Fije un CAJÓN DERECHO (35GC) al LADO DERECHO DE CAJÓN (D12) y un CAJÓN IZQUIERDO (35GD) al LADO IZQUIERDO DE CAJÓN (D13). Utilice cuatro TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 3. NOTA: La cabeza de tornillo del EXCÉNTRICO debe ser visible a través del agujero alargado de la CORREDERA.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
AVERTISSEMENT Prière d’utiliser le mobilier à bon escient et avec prudence. Une mauvaise utilisation peut être à l’origine de risques d’accident ou peut endommager le mobilier et les articles ménagers. Lire attentivement le tableau suivant. À surveiller : Danger éventuel : Solution : • Les enfants qui grimpent sur le mobilier. • Un enfant peut grimper sur le mobilier pour essayer d’attraper un jouet ou tout autre objet. • Les enfants jouèrent et sont actifs à proximité du téléviseur.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
