sauder.com Sweet stand. Sweet dreams. Night Stand Dakota Pass Collection | 418176 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-19 Français pg 20-22 Español pg 23-25 Lot # 367455 02/05/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-19 Hammer Français 20-22 Español 23-25 Safety 26 Warranty 27 Page 2 Not actual size Skip the power trip. This time. 418176 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A and B) and BOTTOM (D). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F B A D 10F www.sauder.
Step 2 å Turn six CAM SCREWS (8F) into the FRONT LEGS (F and G) and TOP MOLDING (J). å Push six HIDDEN CAMS (1F) into the ENDS (A and B) and TOP (C). (6 used) 8F G F J Arrow 1F B A C Arrow Hole Arrow (6 used) Page 6 1F The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. 418176 www.sauder.
Step 3 å å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes # 1 and #3. Remember: Righty tighty. Lefty loosey. *patent pending glide system Glide end 1 2 3 Edge with HIDDEN CAMS 3 S HI urfa DD ce EN wi CA th M S A 2 1 Glide end S HI urfa DD ce EN wi CA th M S B 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Edge with HIDDEN CAMS www.sauder.
Step 4 å Fasten the REAR LEGS (H) to the ENDS (A and B). Use four BLACK 2-1/4" FLAT HEAD SCREWS (26S). These surfaces should be even. Edge with HIDDEN CAMS These surfaces should be even. S HI urfa DD ce EN wi CA th M S A H H B S HI urfa DD ce EN wi CA th M S Angled edge Edge with HIDDEN CAMS 26S BLACK 2-1/4" FLAT HEAD SCREW (4 used in this step) Page 8 418176 www.sauder.
Step 5 å Fasten the LEFT END (B) to the TOP (C). Tighten two TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 6 å Fasten the BOTTOM (D) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. Notched edge B Sur fac D ew ith TW IST -LO Page 10 CK ® FA 418176 STE NER S www.sauder.
Step 7 å Fasten the RIGHT END (A) to the TOP (C) and BOTTOM (D). Tighten four TWIST-LOCK® FASTENERS. Edge with HIDDEN CAMS C A ut itho S w e fac M Sur EN CA D HID D H www.sauder.
Step 8 å å Slide the BOTTOM MOLDING* (K) onto the notched edge of the BOTTOM (D). Don't worry. It isn't Rome. This can be built in a day. *U.S. Patent No. 5,499,886 Notched edge K D Slide the BOTTOM MOLDING (K) onto the notched edge. Page 12 418176 www.sauder.
Step 9 å Tap two MOLDING CONNECTORS (17F) into the notches in the FRONT LEGS (F and G) and TOP MOLDING (J). Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the FRONT LEGS and MOLDING. Flat end Flat end 17F 17F G F J www.sauder.
Step 10 å Insert two WOOD DOWELS (15F) into the FRONT LEGS (F and G). å NOTE: Be very careful when flipping over the FRONT LEGS and TOP MOLDING to fasten to your unit. å Fasten the FRONT LEGS (F and G) and TOP MOLDING (J) to the ENDS (A and B) and TOP (C). Tighten six HIDDEN CAMS. å 1 2 NOTE: Be sure the WOOD DOWELS in the FRONT LEGS insert into the holes in the ENDS. G J F B C A 15F Page 14 418176 www.sauder.
Step 11 å Carefully turn your unit over onto its front edges and lay the BACK (E) over your unit. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (E) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 1N NAIL (18 used in this step) E www.sauder.
Step 12 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D960 D24 D24 I D25 I Groove å D25 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Insert the DRAWER SIDES (D24 and D25) at an angle into the slot at each end of the DRAWER FRONT (I).
Step 13 å Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D24) and a DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D25). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. å NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. å NOTE: The glides are not intended to rotate. Glide end 1 2 D25 Glide end D24 1 2 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 14 å Fasten the DRAWER FRONT MOLDING (L) to the DRAWER FRONT (I). Use two BLACK 1" PAN HEAD SCREWS (60S). å Fasten a KNOB (28K) to the DRAWER FRONT MOLDING (L). Use a SILVER 1-1/2" MACHINE SCREW (95S) through the DRAWER FRONT (I), through the DRAWER FRONT MOLDING, and into the KNOB. 60S BLACK 1" PAN HEAD SCREW (2 used in this step) L I 28K 95S SILVER 1-1/2" MACHINE SCREW (1 used for the KNOB) Page 18 418176 www.sauder.
Step 15 å å Carefully stand your unit upright. å Push a CAM COVER (13P) onto each visible HIDDEN CAM in the ENDS (A and B). å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. To insert the drawer into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit.
418176 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer le DESSOUS (D) à l'EXTRÉMITÉ GAUCHE (B). Serrer deux FIXATIONS TWIST-LOCK®. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A et B) et le DESSOUS (D).
ÉTAPE 11 ÉTAPE 14 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Fixer la MOULURE DE DEVANT DE TIROIR (L) sur le DEVANT DE TIROIR (I). Utiliser deux VIS TÊTE GOUTTE DE SUIF 25 mm NOIRES (60S). Avec précaution, retourner l'élément sur ses chants avant et placer l'ARRIÈRE (E) sur l'élément. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (E).
418176 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije el FONDO (D) al EXTREMO IZQUIERDO (B). Apriete dos SUJETADORES TWIST-LOCK®. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A y B) y del FONDO (D).
PASO 11 PASO 14 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije la MOLDURA DE CARA DE CAJÓN (L) a la CARA DE CAJÓN (I). Utilice dos TORNILLOS NEGROS DE CABEZA REDONDA de 25 mm (60S). Cuidadosamente gire su unidad sobre sus bordes frontales y coloque el DORSO (E) sobre la unidad. Los márgenes a lo largo de todos los bordes del DORSO (E) deben estar uniformes.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
