sauder.com You'll love what we have in storage. Narrow Storage Cabinet Adept Storage Collection | 418085 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Page 2 Not actual size Skip the power trip. This time. 31 418085 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push four SMALL HIDDEN CAMS (29F) into the holes in the DOOR (G). Arrow 29F (4 used) G Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. www.sauder.
Step 2 å Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B), TOP (C), and BOTTOM (E). Then, insert the metal end of eight CAM DOWELS (2F) into the HIDDEN CAMS in the TOP (C) and BOTTOM (E). å NOTE: Do not insert CAM DOWELS into the ENDS (A and B). Do not tighten the HIDDEN CAMS in this step. Arrow Do not insert CAM DOWELS into these parts. 1F A B Arrow 1F (16 used) C E Arrow Arrow 1F 2F (8 used) Page 6 Insert the metal end of the CAM DOWEL into the HIDDEN CAM. 418085 www.sauder.
Step 3 å Turn four CAM SCREWS (8F) into the DOOR MOLDINGS (M). Remember: Righty tighty. Lefty loosey. 8F M M www.sauder.
Step 4 å First, fill the holes in the DOOR MOLDINGS (M) 1/4 to 1/2 full with GLUE (54M). Then, insert four WOOD DOWELS (26F) into the holes. Wipe away the excess GLUE. å Now, fill the outer holes in the edges of the DOOR (G) 1/4 to 1/2 full with GLUE. å Fasten the DOOR MOLDINGS (M) to the DOOR (G). Tighten four HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the DOOR MOLDINGS insert into the holes in the DOOR. Wipe away the excess GLUE.
Step 5 å Fasten the LEFT END (B) to the TOP (C) and BOTTOM (E). Tighten four HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Edge with HIDDEN CAMS These holes must be here. withMS e c fa A Sur DEN C HID B C Fin ishe HID d s DEN urfa CA ce w MS ith These holes must be here. E Sur f HID ace w DEN ith CA MS Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 6 å Fasten the RIGHT END (A) to the TOP (C) and BOTTOM (E). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees C Edge with HIDDEN CAMS ut itho S w e fac AM Sur DEN C HID A E Page 10 418085 www.sauder.
Step 7 å Fasten three METAL BRACKETS (4G) to the ENDS (A and B) and TOP (C). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the METAL BRACKETS are even with the edges of the ENDS and TOP. å Fasten the TOP MOLDING (L) to the ENDS (A and B) and TOP (C). Use three BLACK 9/16" LARGE HEAD SCREWS (1S) 1S BLACK 9/16" LARGE HEAD SCREW (6 used in this step) through the METAL BRACKETS and into the ENDS and TOP. Flat edge L 4G C 4G B A 4G www.sauder.
Step 8 å You have the option for the DOOR to open to the RIGHT or the LEFT. If you choose the DOOR to open to the RIGHT, go to Step 10 now. If you choose the DOOR to open to the LEFT, continue with the next step. DOOR opening to the RIGHT DOOR opening to the LEFT Page 12 418085 www.sauder.
Step 9 å Push four HIDDEN CAMS (1F) into the holes in the HINGE UPRIGHT (D). å å å NOTE: Be sure the locator hole is positioned as shown. å Push a LARGE RUBBER SLEEVE (58G) over the end of the TIE PLATE/DOOR STOP (3G). å Continue on to Step 11 now. Turn twelve CAM SCREWS (8F) into the LEGS (J and K). Fasten a TIE PLATE/DOOR STOP (3G) to the RIGHT LEG (J). Use a BLACK 9/16" LARGE HEAD SCREW (1S).
Step 10 å Push four HIDDEN CAMS (1F) into the holes in the HINGE UPRIGHT (D). å å å NOTE: Be sure the locator hole is positioned as shown. å Push a LARGE RUBBER SLEEVE (58G) over the end of the TIE PLATE/DOOR STOP (3G). Turn twelve CAM SCREWS (8F) into the LEGS (J and K). Fasten a TIE PLATE/DOOR STOP (3G) to the LEFT LEG (K). Use a BLACK 9/16" LARGE HEAD SCREW (1S).
Step 11 å Fasten the LEGS (J and K) to the ENDS (A and B). Tighten eight HIDDEN CAMS. 1 2 K Angled edge J B A www.sauder.
Step 12 å For the DOOR to open to the LEFT, fasten the HINGE UPRIGHT (D) to the LEFT LEG (K) as shown in this step. Tighten four HIDDEN CAMS. å NOTE: Fasten the HINGE UPRIGHT to the RIGHT LEG (J) for the DOOR to open to the RIGHT. å Fasten the HINGE UPRIGHT (D) to the TOP (C) and BOTTOM (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). 1 2 C Surface with HIDDEN CAMS K D J E 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 16 418085 www.sauder.
Step 13 å Fasten a METAL BRACKET (4G) to the BOTTOM (E). Use one BLACK 9/16" LARGE HEAD SCREW (1S). 3G å NOTE: Be sure the edge of the METAL BRACKET is even with the edge of the BOTTOM. å Fasten two TIE PLATE/DOOR STOPS (3G) to the BASE (I). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the BASE (I) to the LEGS (J and K) and BOTTOM (E). Use three BLACK 9/16" LARGE HEAD SCREWS (1S) through the TIE PLATE/DOOR STOPS and METAL BRACKET and into the BASE.
Step 14 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (F) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 1N NAIL (40 used in this step) ed ish fin ce Un rfa su F Page 18 418085 www.sauder.
Step 15 å Place three HINGE SPACERS (22H) over the large holes in the DOORS (G). å Fasten three HINGES (14H) to the DOOR (G). Use six SILVER 5/8" FLAT HEAD SCREWS (23S). 23S SILVER 5/8" FLAT HEAD SCREW (6 used in this step) 14H 22H G www.sauder.
Step 16 å å Carefully stand your unit upright. å Fasten the DOOR (G) to the HINGE UPRIGHT (D) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. å Fasten the PULL (53K) to the DOOR (G). Use two SILVER 3/8" MACHINE SCREWS (97S). å See the next step for DOOR adjustments. Pro Tip: Lift with your legs. And, you know, your arms.
Step 17 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 18 å å Place your unit in its final location against a wall. å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELVES (H) onto the METAL PINS. å å å Push a CAM COVER (33P) onto each visible HIDDEN CAM. We recommend using the SAFETY BRACKET (1G) for added stability.
418085 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer l'EXTRÉMITÉ DROITE (A) au DESSUS (C) et au DESSOUS (E). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Enfoncer quatre PETITES EXCENTRIQUES ESCAMOTABLES (29F) dans les trous de la PORTE (G). ÉTAPE 2 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Enfoncer seize EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), le DESSUS (C) et le DESSOUS (E).
ÉTAPE 11 ÉTAPE 16 Fixer les PIEDS (J et K) aux EXTRÉMITÉS (A et B). Serrer huit EXCENTRIQUES ESCAMOTABLES. Relever, avec précaution, l'élément dans sa position verticale. ÉTAPE 12 Pour ouvrir la PORTE vers la GAUCHE, fixer le MONTANT DE CHARNIÈRE (D) au PIED GAUCHE (K) comme l'indique le schéma. Serrer quatre EXCENTRIQUES ESCAMOTABLES. REMARQUE : Pour ouvrir la PORTE vers la DROITE, fixer le MONTANT DE CHARNIÈRE au PIED DROIT (J). Fixer le MONTANT DE CHARNIÈRE (D) au DESSUS (C) et au DESSOUS (E).
418085 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije el EXTREMO DERECHO (A) al PANEL SUPERIOR (C) y al FONDO (E). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Empuje cuatro EXCÉNTRICOS ESCONDIDOS PEQUEÑOS (29F) dentro de los agujeros de la PUERTA (G). PASO 2 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Empuje dieciséis EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), el PANEL SUPERIOR (C) y el FONDO (E).
PASO 11 PASO 16 Fije las PATAS (J y K) a los EXTREMOS (A y B). Apriete ocho EXCÉNTRICOS ESCONDIDOS. Cuidadosamente ponga la unidad en posición vertical. PASO 12 Para abrir la PUERTA hacia la IZQUIERDA, fije el PARAL DE BISAGRA (D) a la PATA IZQUIERDA (K) como se muestra. Apriete cuatro EXCÉNTRICOS ESCONDIDOS. NOTA: Para abrir la PUERTA hacia la DERECHA, fije el PARAL DE BISAGRA a la PATA DERECHA (J). Fije el PARAL DE BISAGRA (D) al PANEL SUPERIOR (C) y al FONDO (E).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
