sauder.com You'll love what we have in storage. 3-Drawer Cabinet Flat Creek Collection | 417244 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 365050 10/08/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Not actual size Français 19-21 Español 22-24 Straight Edge Screwdriver Safety 25-26 Tape Measure Warranty 27 Skip the power trip. This time. Page 2 417244 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push nine HIDDEN CAMS (1F) into the ENDS (A and B), BACKS (E), and DRAWER BRACES (G). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Insert three SAFETY STOPS (29G) into the holes shown in the RIGHT END (A). 29G A Edge with CAM DOWELS 29G This pin must insert into the location holes in the RIGHT END (A). 29G S HI urfa DD ce EN wi CA th M S 29G A Page 6 417244 www.sauder.
Step 3 å å Diagram 1. Measure 1-1/2" from one end of the INTERLOCK TRACK (26G). Position the INTERLOCK TRACK as shown. å å Diagram 3. Rotate the INTERLOCK TRACK and apply force to snap the second edge into the SAFETY STOP. å Diagram 5. Remove the INTERLOCK TRACK assembly from Diagram 4 and flip it over before inserting the INTERLOCK TRACK (26G) with SAFETY STOPS (29G) into the groove in the RIGHT END (A). SAFETY STOP / TRACK ATTACHMENT: Diagram 2.
Step 4 å Separate the EXTENSION SLIDES (K) from the EXTENSION RAILS (J) as shown in the upper diagram below. Be prepared, the parts are greasy. å Fasten the EXTENSION RAILS (J) to the ENDS (A and B). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S). å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the innercartridge of the EXTENSION RAIL out to find the other hole that lines up with the hole in the END. Turn a SCREW into this hole.
Step 5 å Fasten the TOP (C) to the BACK SPLASH (I). Use three BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S BLACK 1-7/8" FLAT HEAD SCREW (3 used in this step) C ith w s ce ole fa h ur e S or m I www.sauder.
Step 6 å Fasten the ENDS (A and B) to the TOP (C). Tighten four HIDDEN CAMS. Sur withface HID CA DEN MS C A Sur HIDface w DEN itho CA ut MS I B Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 10 Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 417244 www.sauder.
Step 7 å Fasten the BACKS (E) to the TOP (C). Tighten two HIDDEN CAMS. S HI urfa DD ce EN wi CA th M C S HI urfa DD ce EN wi CA th M E E Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
Step 8 å Fasten the BOTTOM (D) to the ENDS (A and B) and BACKS (E). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Fasten the FEET (21E) to the BOTTOM (D). Use sixteen SILVER 1-1/4" PAN HEAD SCREWS (45S). å Now, turn an ADJUSTABLE GLIDE (33E) into the center hole of each FOOT (21E). å NOTE: To raise a corner of the unit, turn the ADJUSTABLE GLIDE counter-clockwise. To lower a corner, turn the ADJUSTABLE GLIDE clockwise.
Step 9 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce B11 D133 D133 D139 F F D139 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å Insert the DRAWER SIDES (D133 and D139) at an angle into the slot at each end of the DRAWER FRONT (F).
Step 10 å å Insert a SLIDE CAM (10A) into the DRAWER RIGHT SIDE (D133). å å Diagram 2. Visually check that the DRAWER STOP (20G) is seated in the SLIDE (K). å Now, fasten the EXTENSION SLIDE (K) to the DRAWER RIGHT SIDE (D133). Use two GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Repeat this step for the other drawers. Diagram 1.
Step 11 å å å Flip the drawer over onto the DRAWER RIGHT SIDE (D133). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Repeat this step for the other drawers. Insert a SLIDE CAM (10A) into the DRAWER LEFT SIDE (D139). Now, fasten an EXTENSION SLIDE (K) to the DRAWER LEFT SIDE (D139). Use two GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Screw head - turn CAM to line up the hole in the SLIDE with hole in the DRAWER SIDE.
Step 12 å Fasten a PULL (35K) to the DRAWER FRONT (F). Use two BLACK 7/8" MACHINE SCREWS (37S). å Repeat this step for the other drawers. 37S BLACK 7/8" MACHINE SCREW (6 used in this step) F 35K Page 16 417244 www.sauder.
Step 13 å å Carefully stand your unit upright. å To insert a drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. å Peel the double-sided TAPE from the TAPE CARD (5M). Apply four pieces of TAPE to the corners of the TOP (C) and stick the RUBBER MAT (H) onto the TAPE.
Step 14 å To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the cam clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the cam. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREWS when finished with adjustments. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly.
417244 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 4 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Séparer les COULISSES D'EXTENSION (K) des GLISSIÈRES D'EXTENSION (J) comme l'indique le schéma ci-dessous supérieure. Faire attention car les pièces sont graissées. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer neuf EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), les ARRIÈRES (E) et les ENTRETOISES DE TIROIR (G).
ÉTAPE 8 ÉTAPE 11 Fixer le DESSOUS (D) aux EXTRÉMITÉS (A et B) et aux ARRIÈRES (E). Utiliser huit VIS TÊTE PLATE 48 mm NOIRES (2S). Retourner le tiroir sur le CÔTÉ DROIT DE TIROIR (D133). Fixer les PIEDS (21E) au DESSOUS (D). Utiliser seize VIS TÊTE GOUTTE DE SUIF 32 mm ARGENTÉES (45S). Maintenant, faire tourner un PATIN RÉGLABLE (33E) dans le trou central de chaque PIED (21E).
417244 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 4 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Separe las CORREDERAS DE EXTENSIÓN (K) de los RIELES DE EXTENSIÓN (J) como se muestra en el diagrama superior mas abajo. Prepárese, las piezas son grasientas. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje nueve EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A y B), los DORSOS (E) y las RIOSTRAS DE CAJÓN (G).
PASO 8 PASO 11 Fije el FONDO (D) a los EXTREMOS (A y B) y a los DORSOS (E). Utilice ocho TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (2S). Vuelva el cajón al revés sobre el LADO DERECHO DE CAJÓN (D133). Fije las PATAS (21E) al FONDO (D). Utilice dieciséis TORNILLOS PLATEADOS DE CABEZA REDONDA de 32 mm (45S). Ahora, fije una CORREDERA DE EXTENSIÓN (K) al LADO IZQUIERDO DE CAJÓN (D139). Utilice dos TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 3.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
