sauder.com WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Chifforobe Pogo Collection | 417146 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Page 2 Not actual size Skip the power trip. This time. 31 417146 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1N NAIL - 58 1R 8R SHELF SNAP - 4 1S BLACK 9/16" LARGE HEAD SCREW - 11 3S 9S BLACK 1-1/8" PAN HEAD SCREW - 13 14S BROWN 1-1/2" FLAT HEAD SCREW - 3 METAL PIN - 4 GOLD 5/16" FLAT HEAD SCREW - 34 20S SILVER 3/4" MACHINE SCREW - 9 23S SILVER 5/8" FLAT HEAD SCREW - 4 30S BLACK 1-9/16" FLAT HEAD SCREW - 20 78S SILVER 1/2" FLAT HEAD SCREW - 2 113S BLACK 1-15/16" FLAT HEAD SCREW - 2 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B) UPRIGHT (C), BOTTOM (E2), and DRAWER BRACES (M67). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the RIGHT END (A) and UPRIGHT (C). Use sixteen GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Remember: Righty tighty. Lefty loosey. *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (16 used in this step) Glide end 1 2 1 3 2 1 3 3 2 1 3 1 3 2 2 3 1 3 C Glide end 2 A 2 1 3 2 1 www.sauder.
Step 3 å å Flip the UPRIGHT (C) over. Fasten the ROD HANGERS (19A) to the UPRIGHT (C) and LEFT END (B). Use two SILVER 1/2" FLAT HEAD SCREWS (78S). 78S SILVER 1/2" FLAT HEAD SCREW (2 used in this step) 19A C B Page 8 417146 www.sauder.
Step 4 å Fasten the LEFT END (B) and UPRIGHT (C) to the TOP (D). Tighten four HIDDEN CAMS. Notch Rounded edge Finished edge D ce rfa oles u S hh wit C B Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 5 å Fasten the BOTTOM (E2) to the LEFT END (B). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (E2) to the UPRIGHT (C). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Push a DOOR STOP (4I) into the hole near the notch in the UPRIGHT (C). Maximum 210 degrees Arrow Minimum 190 degrees 4I B C E2 Sur fac ew ith HID DEN CA MS 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) Page 10 417146 www.sauder.
Step 6 å Fasten the RIGHT END (A) to the TOP (D) and BOTTOM (E2). Tighten four HIDDEN CAMS. å Fasten the TOP MOLDING (M) to the TOP (D). Use three BROWN 1-1/2" FLAT HEAD SCREWS (14S). å NOTE: Do not overtighten the SCREWS into the TOP. Maximum 210 degrees Arrow Minimum 190 degrees 14S Curved edge BROWN 1-1/2" FLAT HEAD SCREW (3 used in this step) Do not overtighten the SCREWS (14S). M D A E2 www.sauder.
Step 7 å Fasten three METAL BRACKETS (4G) to the BOTTOM (E2) and a METAL BRACKET to each END (A and B). Use five BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the BRACKETS are even with the edges of the ENDS and BOTTOM. å Fasten the SKIRT (J) to the BOTTOM (E2). Use five BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the BALLAST (N) to the BOTTOM (E2). Use four BLACK 1-1/8" PAN HEAD SCREWS (9S). 4G J Don't worry. It isn't Rome. This can be built in a day.
Step 8 å Carefully turn your unit over onto its front edges. Lay the SMALL BACK (G) over the small opening of your unit. å Make equal margins along all four edges of the SMALL BACK (G). Push on opposite corners of your unit if needed to make it "square". å å Fasten the SMALL BACK (G) to your unit using twenty-four NAILS (1N). å å å NOTE: The LARGE BACK will overlap the SMALL BACK. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 9 å Fasten two HINGES (14H) and two HINGE SPACERS (22H) to the DOOR (H). Use four SILVER 5/8" FLAT HEAD SCREWS (23S). 23S SILVER 5/8" FLAT HEAD SCREW (4 used in this step) 14H 22H H Page 14 417146 www.sauder.
Step 10 å å Carefully stand your unit upright. Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten the DOOR (H) to the LEFT END (B) Use the screws in the HINGE. See the next step for door adjustments. å You have the option of fastening a WOOD KNOB (60K) or a CLEAR KNOB (107K) to the DOOR (H).
Step 11 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 12 VIEW THE T-LOCK BOX VIDEO The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 1 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. 2 Un fi su nish rfa ed ce D30 D733 D30 D31 K K Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å D31 Insert the DRAWER SIDES (D30 and D31) at an angle into the slot at each end of the DRAWER FRONT (K).
Step 13 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D30 and D31). å NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification and the glides are not intended to rotate. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Repeat this step for the remaining drawers. If you're doing this to help a friend, don't leave without a bite.
Step 14 å You have the option of fastening a WOOD KNOB (60K) or a CLEAR KNOB (107K) to the DRAWER FRONTS (K and L). å Fasten the CLEAR KNOBS (107K) to the DRAWER FRONT (K) with a SILVER 3/4" MACHINE SCREW (20S) or fasten the WOOD KNOBS (60K) to the DRAWER FRONT (K) with a BLACK 1-1/8" PAN HEAD SCREW (9S). å Repeat this step for the remaining drawers. 9S BLACK 1-1/8" PAN HEAD SCREW (8 used in this step) (8 used) 60K 20S SILVER 3/4" MACHINE SCREW (8 used for the METAL KNOB) (8 used) 107K K www.
Step 15 å å Position your unit in its final location. We recommend using the SAFETY STRAP (60M) for added stability. å INSTALLATION INSTRUCTIONS: (Also available at www.yl-anchors.com) 1. Insert the SAFETY DRYWALL ANCHOR (61M) through the WASHER (13M) and one end of the SAFETY STRAP (60M). 2. Using a Phillips screwdriver or a hand drill, press screw slightly onto the drywall. 3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips through. 4.
Step 16 å With a hammer, gently tap four SHELF SNAPS (8R) into the holes in the ADJUSTABLE SHELF (I). å Insert the METAL PINS (1R) into the hole locations of your choice in the LEFT END (A) and UPRIGHT (C). Set the ADJUSTABLE SHELF (I) onto the METAL PINS so the SHELF SNAPS are resting on the METAL PINS. Push on the SHELF until each METAL PIN "snaps" into the SHELF SNAP.
Step 17 å To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
417146 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer trois CONSOLES EN MÉTAL (4G) au DESSOUS (E2) et une CONSOLE EN MÉTAL à chaque EXTRÉMITÉ (A et B). Utiliser cinq VIS TÊTE LARGE 14 mm NOIRES (1S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer quatorze EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), le MONTANT (C), le DESSOUS (E2) et les ENTRETOISES DE TIROIR (M67).
ÉTAPE 11 ÉTAPE 15 (SUITE) Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. REMARQUE : Ne pas tourner le DISPOSITIF DE SÉCURITÉ POUR PLACOPLÂTRE (61M) dans un montant mural. Si on préfère fixer la SANGLE DE SÉCURITÉ (60M) à un montant mural, obtenir la visserie appropriée auprès d’une quincaillerie locale. Il faut peut-être ajuster les PORTES. Suivre les indications ci-dessous pour ajuster.
417146 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 (CONTINUACIÓN) No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el FALDÓN (J) al FONDO (E2). Utilice cinco TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje catorce EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A y B), el PARAL (C), el FONDO (E2) y las RIOSTRAS DE CAJÓN (M67).
PASO 11 (CONTINUACIÓN) PASO 15 (CONTINUACIÓN) AJUSTE DE LA PUERTA: Para ajustar las PUERTAS de un lado al otro (horizontalmente), afloje el tornillo de montaje varias vueltas y gire el tornillo de ajuste hacia el interior o hacia el exterior. Apriete el tornillo de montaje después de hacer los ajustes. NOTA: No gire el ANCLAJE DE SEGURIDAD PARA EL DRYWALL (61M) en un montante de la pared.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
