sauder.com Here's one for the books. Library with Doors Carson Forge Collection | 416967 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 361928 05/20/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification C N L F A H P M H P B E J O I K D G G O www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twenty-four HIDDEN CAMS (1F) into the ENDS (A and B) and SHELF (E). Then, insert the metal end of eight CAM DOWELS (2F) into each HIDDEN CAM except the long edges of the ENDS (A and B). Do not tighten the HIDDEN CAMS in this step. Do not insert CAM DOWELS into the long edges.
Step 2 å Turn sixteen CAM SCREWS (8F) into the LEGS (J, K, L, and M). Remember: Righty tighty. Lefty loosey. 8F (16 used) K J L M Page 6 416967 www.sauder.
Step 3 å Fasten the REAR LEGS (L and M) to the ENDS (A and B). Tighten eight HIDDEN CAMS. These surfaces should be even. Angled edge S wi urfa H th ce CA IDD M EN S These surfaces should be even. M L S wi urfa H th ce CA IDD M EN S B A Edge with CAM DOWELS Edge with CAM DOWELS 1 2 www.sauder.
Step 4 å Fasten the LEFT END (B) to the TOP (C). Tighten two HIDDEN CAMS. å Fasten the SHELF (E) to the LEFT END (B). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Curved edge This hole must be here. C MS CA N E IDD H h it ew c a f Sur E B Su witrface hh ole s Sur HIDface w DEN ith CA MS M Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 5 å Fasten the BOTTOM (D) to the LEFT END (B). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). å NOTE: Use the two holes closest to the bottom edge of the LEFT END. å Push the DOOR STOP (4I) into the hole in the SHELF (E). 2S 4I BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) B E D www.sauder.
Step 6 å Fasten the RIGHT END (A) to the TOP (C) and SHELF (E). Tighten four HIDDEN CAMS. å Fasten the RIGHT END (A) to the BOTTOM (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). C out h t i ew fac r u S E MS CA N DE HID L A D 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Maximum 210 degrees Arrow Minimum 190 degrees Page 10 416967 www.sauder.
Step 7 å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS. å Slide the BOTTOM MOLDINGS (O) onto the ENDS (A and B). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS. These edges should be even. B O O A O A 32S BLACK 9/16" FLAT HEAD SCREW (4 used in this step) Shoulder Apply pressure with your hands as you guide the MOLDINGS over the SCREWS and onto the ENDS. www.sauder.
Step 8 å Fasten two CORNER ACCENTS (8E) to the FRONT LEGS (J and K). Use two SILVER 5/8" MACHINE SCREWS (15S). 15S SILVER 5/8" MACHINE SCREW (2 used in this step) J K 8E 8E Page 12 416967 www.sauder.
Step 9 å Fasten the FRONT LEGS (J and K) to the ENDS (A and B). Tighten eight HIDDEN CAMS. Hey! It's starting to look like something! K Angled edge B J A Angled edge www.sauder.
Step 10 å Fasten three ANGLE BRACKETS (27G) to the TOP (C). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the VALANCE MOLDING (N) to the TOP (C). Use three BLACK 9/16" LARGE HEAD SCREWS (1S) through the ANGLE BRACKETS and into the VALANCE MOLDING. å NOTE: There are no pre-drilled holes in the VALANCE MOLDING. The SCREWS will tighten into the groove. 1S BLACK 9/16" LARGE HEAD SCREW (6 used in this step) N 27G C Page 14 416967 www.sauder.
Step 11 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the SHELF (E).
Step 12 å å Push four FEET (10E) onto the LEGS (J, K, L, and M). With your hammer, gently tap four TACK GLIDES (12E) through the FEET and into the LEGS (J, K, L, and M). 10E 12E L M J K 10E 12E Page 16 416967 www.sauder.
Step 13 å Fasten two HINGES (14H) to each DOOR (G). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). 14H 11S BLACK 1/2" FLAT HEAD SCREW (8 used in this step) G G 14H www.sauder.
Step 14 å å Carefully stand your unit upright. å Fasten one of the DOORS (G) to the LEFT END (B). Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. Pro Tip: Lift with your legs. And, you know, your arms. Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw.
Step 15 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 16 å Slide a SHELF MOLDING* (P) onto the notched edge of one of the ADJUSTABLE SHELVES (H). å å Repeat this step for the other ADJUSTABLE SHELF (H). *U.S. Patent No. 5,499,886 Notched edge H P Slide the SHELF MOLDING (P) onto the notched edge. Page 20 416967 www.sauder.
Step 17 å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. BLACK 1-7/8" FLAT HEAD SCREW (1 used into a stud in your wall) 2S 1G BLACK 9/16" LARGE HEAD SCREW (1 used into the top of your unit) 1S www.sauder.
Step 18 å Push the RUBBER SLEEVES (2R) over the ends of the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B). Set the ADJUSTABLE SHELVES (H and I) onto the METAL PINS. å å å Push a CAM COVER (12P) onto each visible HIDDEN CAM. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
416967 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer l'EXTRÉMITÉ DROITE (A) au DESSUS (C) et à la TABLETTE (E). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer l'EXTRÉMITÉ DROITE (A) au DESSOUS (D). Utiliser deux VIS TÊTE PLATE 48 mm NOIRES (2S). Enfoncer vingt-quatre EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B) et la TABLETTE (E).
ÉTAPE 12 ÉTAPE 16 Fixer quatre PIEDS (10E) sur les PIEDS (J, K, L et M). Enfiler la MOULURE DE TABLETTE* (P) sur le chant cranté d'une des TABLETTES RÉGLABLES (H). À l’aide d’un marteau, enfoncer délicatement quatre PATINS (12E) à travers les PIEDS et dans les PIEDS (J, K, L et M). Répéter cette étape pour l'autre TABLETTE RÉGLABLE (H). * Brevet État Unis n° 5,499,886 ÉTAPE 13 Fixer deux CHARNIÈRES (14H) à chaque PORTE (G). Utiliser huit VIS TÊTE PLATE 13 mm NOIRES (11S).
416967 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Atornille cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 14 mm (32S) en los EXTREMOS (A y B) hasta que los resaltos de los TORNILLOS repose sobre las superficies de los EXTREMOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje veinticuatro EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A y B) y el ESTANTE (E).
PASO 12 PASO 16 Fije cuatro PATAS (10E) sobre las PATAS (J, K, L y M). Deslice la MOLDURA DE ESTANTE* (P) sobre el borde con muesca de uno de los ESTANTES AJUSTABLES (H). Con su martillo, golpee suavemente cuatro TACHUELAS DESLIZANTES (12E) a través de las PATAS y entre las PATAS (J, K, L y M). Repita este paso para el otro ESTANTE AJUSTABLE (H). *Patente EE. UU. No. 5,499,886 PASO 13 PASO 17 Fije dos BISAGRAS (14H) a cada PUERTA (G). Utilice ocho TORNILLOS NEGROS DE CABEZA PERDIDA de 13 mm (11S).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
