sauder.com Store behind closed doors. Storage Cabinet Harbor View Collection | 416825 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-15 Français pg 16-17 Español pg 18-20 Lot # 362409 06/05/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-15 Hammer Français 16-17 Español 18-20 Safety 21-22 Warranty Page 2 Not actual size Skip the power trip. This time. 23 416825 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), SHELF (E), and BOTTOM (F). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Tap two MOLDING CONNECTORS (18F) into the notches in the MOLDINGS (L, M, and N). Use your hammer to tap the MOLDING CONNECTORS (18F) into the notches in the MOLDINGS. Flat end Flat end 18F Unfinished surface 18F N Unfinished surface Unfinished surface L Page 6 M 416825 www.sauder.
Step 3 å Flip the MOLDINGS (L, M, and N) over and fasten the MOLDINGS to the TOP (D). Use seven SILVER 2" FLAT HEAD SCREWS (57S). Remember: Righty tighty. Lefty loosey. 57S SILVER 2" FLAT HEAD SCREW (7 used in this step) Curved edge M D ce fa ur S ith s w ole h L Curved edge N Rounded edge www.sauder.
Step 4 å Fasten the LEFT END (B) to the LEFT MOLDING (N). Tighten two HIDDEN CAMS. å Fasten the SHELF (E) to the LEFT END (B). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Curved edge Finished edge N L D B Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 5 å Fasten the UPRIGHT (C) to the SHELF (E). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (F) to the LEFT END (B). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (F) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Fasten the RIGHT END (A) to the SHELF (E), BOTTOM (F), and RIGHT MOLDING (M). Tighten six HIDDEN CAMS. Finished edge Finished edge These holes must be here.
Step 6 å Fasten four METAL BRACKETS (4G) to the ENDS (A and B) and BOTTOM (F). Use four 9/16" LARGE HEAD SCREWS (1S). å Fasten the SKIRT (K) to the ENDS (A and B) and BOTTOM (F). Use four 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the SKIRT. 1S BLACK 9/16" LARGE HEAD SCREW (8 used in this step) Curved edge K ed h is n Fi e ac rf su B F A 4G 4G 4G Page 10 416825 www.sauder.
Step 7 å Carefully turn your unit over onto its front edges. Unfold the BACK (G) and lay it over your unit. å Make equal margins along all four edges of the BACK (G). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (G) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHT (C) and SHELF (E).
Step 8 å Fasten the HINGES (13H) to the DOORS (H and I). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). 11S BLACK 1/2" FLAT HEAD SCREW (8 used in this step) 13H I H 13H Page 12 416825 www.sauder.
Step 9 å å Carefully stand your unit upright. å Fasten the LEFT DOOR (I) to the LEFT END (B). Use the screws in the HINGES. See the next step for adjustments. å Fasten a KNOB (105K) to the LEFT DOOR (I). Use a BLACK 1-1/8" PAN HEAD SCREW (9S). å Peel the FELT DISC from the FELT DISC CARD (1M). Stick a FELT DISC on the DOOR where it comes in contact with the SHELF (E). å Pro Tip: Lift with your legs. And, you know, your arms.
Step 10 å å Refer to the enlarged diagram to identify the parts on the HINGES. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 11 å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (J) onto the METAL PINS.
416825 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 (SUITE) Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (G). Si besoin est, enfoncer sur les coins opposés de l'élément pour s'assurer d'être "d'équerre". Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer quatorze EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), le MONTANT (C), la TABLETTE (E) et le DESSOUS (F).
416825 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el PARAL (C) al ESTANTE (E). Apriete dos EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje catorce EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A y B), el PARAL (C), el ESTANTE (E) y el FONDO (F). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (2F) dentro de cada EXCÉNTRICO ESCONDIDO.
PASO 8 PASO 10 Fije las BISAGRAS (13H) a las PUERTAS (H e I). Utilice ocho TORNILLOS NEGROS DE CABEZA PERDIDA de 13 mm (11S). Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. PASO 9 Cuidadosamente ponga la unidad en posición vertical. Antes de ajustar la PUERTA a su unidad, asegúrese de que el tornillo de montaje se encuentre contra los topes como se muestra en el diagrama derecho. Si no lo está, afloje el tornillo de montaje para que se deslice contra los topes.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
