sauder.com Yes, you still have to dress yourself. Dresser County Line Collection | Model 416008 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 372500 05/14/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification No. 2 Phillips Screwdriver Tip Shown Actual Size 4 Assembly Steps 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification D2 I F A2 H C2 N D212 D166 I D975 B2 E2 D213 O M65 J H P P D50 D167 D212 D166 D975 D975 D51 M65 D213 D50 M65 K D167 L D975 D51 M65 M www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A2 and B2) and UPRIGHT (C2). å Repeat this step for the BOTTOM (E2). Scan this QR code or go to this address: http://qr.sauder.com/?ID=1280 to watch a video on how to assemble your unit.
Step 2 å Push twelve HIDDEN CAMS (1F) into the ENDS (A2 and B2) and DRAWER BRACES (M65). Just think. The sooner you do this, the sooner you do something else. Arrow 1F Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S A2 Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S B2 Arrow 1F M65 M65 M65 M65 M65 M65 Arrow Arrow 1F (12 used) Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 416008 www.sauder.
Step 3 å Turn twelve CAM SCREWS (8F) into the FRONT LEGS (H) and DRAWER FRONTS (J, K, L, and M). 8F (12 used) M M H K H www.sauder.
Step 4 å Insert two WOOD DOWELS (15F) into the indicated holes in the FRONT LEGS (H). å Fasten the FRONT LEGS (H) to the ENDS (A2 and B2). Tighten six HIDDEN CAMS. å NOTE: Be sure the WOOD DOWELS in the LEGS insert into the ENDS. 1 2 Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S These surfaces should be even. These surfaces should be even. B2 H Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S H 15F A2 15F Page 8 416008 www.sauder.
Step 5 å Fasten the BACK LEGS (I) to the ENDS (A2 and B2). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S). These surfaces should be even. Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S I These surfaces should be even. Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S B2 A2 I 26S BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) www.sauder.
Step 6 VIEW THE DRAWER GLIDE VIDEO å Fasten six UNIVERSAL CABINET RAILS* (40DA) to the ENDS (A2 and B2). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (12 used in this step) Glide end 1 2 3 1 4 2 1 3 4 4 2 A2 3 3 4 Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S 2 4 1 3 2 4 1 3 2 1 Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S B2 Glide end Page 10 416008 www.sauder.
Step 7 VIEW THE DRAWER GLIDE VIDEO å Fasten six UNIVERSAL CABINET RAILS* (40DA) to the UPRIGHT (C2). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (12 used in this step) 4 3 2 4 1 3 C2 2 Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S 4 1 3 2 1 2 1 2 4 Glide end 3 1 2 1 www.sauder.
Step 8 å Fasten the LEFT END (B2) to the TOP (D2). Tighten two TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Finished edge H B2 ith e w K® c a C f Sur T-LO S S I R TW TENE FAS Su D2 rfa ce wit hh ole s Dowel end How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
Step 9 å Fasten the UPRIGHT (C2) to the TOP (D2). Tighten two TWIST-LOCK® FASTENERS. Don't worry. It isn't Rome. This can be built in a day. D2 Finished edge C2 www.sauder.
Step 10 å Fasten the BOTTOM (E2) to the LEFT END (B2). Tighten two TWIST-LOCK® FASTENERS. å Fasten the BOTTOM (E2) to the UPRIGHT (C2). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Slide the BOTTOM MOLDING* (O) onto the notched edge of the BOTTOM (E2). å *U.S. Patent No. 5,499,886 Notched edge B2 C2 E2 Sur f TW ace wi IS th FAS T-LO TEN CK® ERS O 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) Groove Wide edge Page 14 416008 www.sauder.
Step 11 å Fasten the RIGHT END (A2) to the TOP (D2) and BOTTOM (E2). Tighten four TWIST-LOCK® FASTENERS. å Fasten the METAL BRACKETS (4G) to the ENDS (A2 and B2) and UPRIGHT (C2). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the FRONT MOLDING (N) to the ENDS (A2 and B2) and UPRIGHT (C2). Use three BLACK 9/16" LARGE HEAD SCREWS (1S) through the BRACKETS and into the MOLDING.
Step 12 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 1N NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHT (C2).
Step 13 å Fasten the FOOT BRACKET (6E) to the BOTTOM (E2). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å å å Slide the FEET (P) onto the FOOT BRACKET (6E). Slide the CORNER CAP (5E) onto the FEET (P). Turn two BLACK 9/16" LARGE HEAD SCREWS (1S) into the short slots of the FOOT BRACKET (6E). 1S BLACK 9/16" LARGE HEAD SCREW (5 used in this step) E2 1S P 6E 6E P Completed foot support 5E www.sauder.
Step 14 å Fasten the LOWER DRAWER SIDES (D50 and D51) to the LOWER DRAWER BACK (D167). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). å Slide the DRAWER BOTTOM (D975) into the grooves in the LOWER DRAWER SIDES and LOWER DRAWER BACK. å Repeat this step for the other drawers. 30S D51 BLACK 1-9/16" FLAT HEAD SCREW (24 used in this step) D167 D50 Groove Be sure the DRAWER BOTTOM inserts into the DRAWER BACK groove.
Step 15 å Pull the LARGE DRAWER FRONT BRACKETS (9G) apart and slide them into the grooves in the LOWER DRAWER SIDES (D50 and D51). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification. å Fasten the LOWER RIGHT DRAWER FRONT (L) to the LARGE DRAWER FRONT BRACKETS (9G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å å Repeat this step for the other drawers.
Step 16 å Flip the drawer over and fasten the DRAWER BRACE (M65) to the LOWER RIGHT DRAWER FRONT (L). Tighten the HIDDEN CAM. å Fasten the DRAWER BRACE (M65) to the LOWER DRAWER BACK (D167). Use one BLACK 1-9/16" FLAT HEAD SCREW (30S). å Repeat this step for the other drawers. 1 2 L M65 D167 30S BLACK 1-9/16" FLAT HEAD SCREW (6 used in this step) Page 20 416008 www.sauder.
Step 17 å Fasten a DRAWER RIGHT (40DC) to the LOWER DRAWER RIGHT SIDE (D50) and a DRAWER LEFT (40DD) to the LOWER DRAWER LEFT SIDE (D51). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. å å NOTE: The glides are not intended to rotate. å Repeat this step for the other drawers. If you're doing this to help a friend, don't leave without a bite. Fasten a PULL (98K) to the LOWER RIGHT DRAWER FRONT (L). Use two WASHERS (10I) and two SILVER 1/4" MACHINE SCREWS (61S).
Step 18 å å Carefully stand your unit upright. å To make adjustments to the drawers, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS. å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 2-1/4" FLAT HEAD SCREW (26S) into a stud in your wall. å Apply the WARNING LABEL (5L) to the upper DRAWER LEFT SIDE (D213).
Modèle 416008 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer six GLISSIÈRES D'ÉLÉMENT UNIVERSELLES* (40DA) au MONTANT (C2). Utiliser douze VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 4. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A2 et B2) et le MONTANT (C2).
ÉTAPE 12 ÉTAPE 16 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Retourner le tiroir et fixer l’ENTRETOISE DE TIROIR (M65) au DEVANT DE TIROIR DROIT INFÉRIEUR (L). Serrer l’EXCENTRIQUE ESCAMOTABLE. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (F) et le placer sur l'élément. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (F).
Cómoda Modelo 416008 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije seis RIELES UNIVERSALES DE GABINETE* (40DA) al PARAL (C2). Utilice doce TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 4. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) en los agujeros grandes de los EXTREMOS (A2 y B2) y del PARAL (C2).
PASO 12 PASO 16 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Da vuelta al cajón y apriete la RIOSTRA DE CAJÓN (M65) a la CARA DERECHA DE CAJÓN INFERIOR (L). Apriete el EXCÉNTRICO ESCONDIDO. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (F) y colóquelo sobre la unidad. Fije la RIOSTRA DE CAJÓN (M65) al DORSO DE CAJÓN INFERIOR (D167). Utilice un TORNILLO NEGRO DE CABEZA PERDIDA de 40 mm (30S).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from the bottom to the top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda sobrecargados. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones y estantes sobrecargados pueden romperse. • Nunca exceda los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
