sauder.com You won't just fall in love with it. You'll fall asleep in it. Full/Queen Bookcase Headboard County Line Collection | 415997 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-16 Hammer Français 17-19 Español 20-22 Warranty Page 2 Not actual size Skip the power trip. This time. 23 415997 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A RIGHT END (1) E TOP (1) I BACK (1) B LEFT END (1) F FRONT PANEL (1) J END MOLDING (2) C UPPER UPRIGHT (1) G2 UPPER SHELF (1) D LOWER UPRIGHT (1) H2 LOWER SHELF (1) I E C G2 A J D H2 F B J www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 16G HEADBOARD BRACKET - 2 10F TWIST-LOCK® FASTENER - 12 24M NUT - 4 13M WASHER - 4 1N 1S 113S Page 4 27G ANGLE BRACKET - 4 1R NAIL - 32 METAL PIN - 8 94S SILVER 2" BOLT - 4 BLACK 9/16" LARGE HEAD SCREW - 16 BLACK 1-15/16" FLAT HEAD SCREW - 4 415997 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A and B). å Repeat this step for the FRONT PANEL (F) and LOWER SHELF (H). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F (12 used) B A www.sauder.
Step 2 å Slide the END MOLDINGS (J) onto the notched edges of the ENDS (A and B). å *U.S. Patent No. 5,499,886 Notched edge i th ® e w LOCK S c a f Sur WIST TENER T AS F i th K ® ce w -LOC RS a f r S u W IS T T E N E T AS F These surfaces should be even. B A J Slide the END MOLDING (J) onto the notched edge. Page 6 415997 J www.sauder.
Step 3 å Fasten the LEFT END (B) to the TOP (E). Tighten two TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Long finished edge E J B i th e w K® c a C f Sur ST-LO S I TW TENER FAS Su witrface hh ole s Dowel end How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
Step 4 å å Insert two METAL PINS (1R) into the TOP (E). å NOTE: The edge with larger holes will go onto the METAL PINS. Push the UPPER UPRIGHT (C) onto the METAL PINS in the TOP (E). E Finished edge C 1R Page 8 415997 www.sauder.
Step 5 å Insert two METAL PINS (1R) into the holes in the LEFT END (B). å Push the UPPER SHELF (G2) onto the METAL PINS in the LEFT END (B). å Fasten the UPPER SHELF (G2) to the UPPER UPRIGHT (C). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). å NOTE: Use the two holes that are drilled completely through the UPPER SHELF. å Insert two METAL PINS (1R) into the holes in the UPPER SHELF (G2). Don't worry. It isn't Rome. This can be built in a day.
Step 6 å Push the edge of the LOWER UPRIGHT (D) with the large holes onto the METAL PINS in the UPPER SHELF (G2). å Fasten the LOWER SHELF (H2) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. å Fasten the LOWER SHELF (H2) to the LOWER UPRIGHT (D). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). Finished edge Sur TWface w FASIST-LOith TEN CK ERS ® D H2 113S G2 BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) Page 10 415997 www.sauder.
Step 7 å Fasten the ANGLE BRACKETS (27G) to the FRONT PANEL (F). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: The ANGLE BRACKETS should be even with the edge of the FRONT PANEL. 1S S TW urfa FA IS ce ST T-L wit EN O h ER CK S ® BLACK 9/16" LARGE HEAD SCREW (4 used in this step) Finished edge F 27G www.sauder.
Step 8 å å Carefully turn your unit onto the TOP (E). å Fasten the FRONT PANEL (F) to the LOWER SHELF (H2). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the BRACKETS and into the LOWER SHELF. Fasten the FRONT PANEL (F) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. 1S BLACK 9/16" LARGE HEAD SCREW (4 used in this step) B Finished edge Sur TWface w FASIST-LOith TEN CK ERS ® F E H2 Page 12 415997 www.sauder.
Step 9 å å Insert two METAL PINS (1R) into the holes in the RIGHT END (A). å NOTE: Be sure the METAL PINS in the RIGHT END insert into the holes in the UPPER SHELF (G2). Fasten the RIGHT END (A) to the TOP (E), LOWER PANEL (F), and LOWER SHELF (H2). Tighten six TWIST-LOCK® FASTENERS. F e fac Sur ut K® o C with T-LO S S I TW ENER T FAS H2 G2 A J E 1R www.sauder.
Step 10 å Carefully turn your unit over onto its front edges. Lay the BACK (I) over your unit. å Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (I) to your unit using the NAILS (1N). å Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHTS (C and D).
Step 11 å Fasten the HEADBOARD BRACKETS (16G) to the ENDS (A and B). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S) in the holes that are best suited for the height of your bedframe. If you're doing this to help a friend, don't leave without a bite. 1S BLACK 9/16" LARGE HEAD SCREW (8 used in this step) A 16G B 16G www.sauder.
Step 12 å Fasten your unit to your bedframe. Use four SILVER 2" BOLTS (94S), four WASHERS (13M), and four NUTS (24M) through the BRACKETS and into the bedframe. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? 20 lbs.total 25 lbs. total 25 lbs. total 24M 13M 94S 94S 13M SILVER 2" BOLT WASHER (4 of each used in this step) Page 16 415997 24M NUT www.sauder.
Tête de lit Bibliothèque (Lit grand format et Lit très grand format) 415997 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Insérer deux GOUPILLES EN MÉTAL (1R) dans les trous dans l'EXTRÉMITÉ GAUCHE (B). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A et B). Répéter cette étape pour le PANNEAU AVANT (F) et la TABLETTE INFÉRIEURE (H).
ÉTAPE 8 ÉTAPE 10 Avec précaution, retourner l'élément sur son DESSUS (E) Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Fixer le PANNEAU AVANT (F) à l'EXTRÉMITÉ GAUCHE (B). Serrer deux FIXATIONS TWIST-LOCK®. Fixer le PANNEAU AVANT (F) à la TABLETTE INFÉRIEURE (H2). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (1S) à travers les CONSOLES et dans la TABLETTE INFÉRIEURE.
Cabecera para cama de tamaño matrimonial "reina" con biblioteca 415997 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los SUJETADORES TWIST-LOCK® en este paso. Inserte dos ESPIGAS DE METAL (1R) en los agujeros del EXTREMO IZQUIERDO (B). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A y B). Repita este paso para el PANEL DELANTERO (F) y el ESTANTE INFERIOR (H).
PASO 8 PASO 10 Cuidadosamente voltee la unidad para que repose sobre el PANEL SUPERIOR (E). Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije el PANEL DELANTERO (F) al EXTREMO IZQUIERDO (B). Apriete dos SUJETADORES TWIST-LOCK®. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Coloque el DORSO (I) sobre la unidad. Fije el PANEL DELANTERO (F) al ESTANTE INFERIOR (H2).
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
