sauder.com The original desktop. Work Table Cannery Bridge Collection | 415910 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-26 Français pg 27-29 Español pg 30-32 Lot # 373062 05/22/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification No. 2 Phillips Screwdriver Tip Shown Actual Size 4 Assembly Steps 5-26 Français 27-29 Español 30-32 Safety 33-34 Warranty Hammer Not actual size Tape Measure 35 Skip the power trip. This time. Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification D N P2 C R N L2 R O2 H N G F N A2 J2 M2 T B V N E Q K2 U I N D132 D159 D969 S D138 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Do not tighten the HIDDEN CAMS in this step. Push twenty-two HIDDEN CAMS (1F) into the ENDS (A2, B, and C), BOTTOM (E), BACK (F), and VALANCES (R). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM except for the short edges of the VALANCES (R) and the BACK (F).
Step 2 å Turn six BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A2 and B) and BACK (F) until the shoulder of the SCREWS rest on the surface of the ENDS and BACK. å Slide the MOLDINGS (T, U, and V) onto the ENDS (A2 and B) and BACK (F). Line up the groove in the MOLDINGS over the head of the SCREWS in the ENDS and BACK.
Step 3 å å Fasten the FRONT LEGS (J2 and K2) and REAR LEGS (L2 and M2) to the ENDS (A2 and B). Use twelve BLACK 1-15/16" FLAT HEAD SCREWS (113S). Remember: Righty tighty. Lefty loosey. NOTE: Be sure to position the LEGS exactly as shown. These surfaces should be even. These holes must be here. J2 Groove A2 S HI urfa DD ce EN wi CA th M S These surfaces should be even. L2 M2 S HI urfa DD ce EN wi CA th M S B Groove K2 Groove 113S BLACK 1-15/16" FLAT HEAD SCREW (12 used in this step) www.
Step 4 å Fasten the LEGS (O2 and P2) to the OUTER END (C). Use four BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Fasten the STRETCHER (H) to the LEGS (O2 and P2). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). These surfaces should be even. S HI urfa DD ce EN wi CA th M S This hole must be here. This hole must be here. O2 Groove C The larger hole must be here. P2 H 113S Groove BLACK 1-15/16" FLAT HEAD SCREW (6 used in this step) Page 8 415910 www.sauder.
Step 5 å Fasten the CABINET RIGHT (40CA) and CABINET LEFT (40CB) to the ENDS (A2 and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Roller end 1 2 3 4 J2 S HI urfa DD ce EN wi CA th M S A2 4 3 Roller end 2 1 K2 S HI urfa DD ce EN wi CA th M S B 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 6 å å å å Apply two beads of GLUE (54M) along either side of the groove of two OUTER LEGS (N). å NOTE: When tapping in the I-BEAMS, you will want to alternate by tapping one I-BEAM into the top end and then tapping one into the bottom end until they are all inserted into the LEGS. å å Repeat this step to fasten the remaining OUTER LEGS (N) to the LEGS (J2, K2, L2, and M2) on the ENDS (A2 and B). NOTE: Be sure to leave approximately 2" on either end of the OUTER LEGS without GLUE.
Step 7 å Turn eight CAM SCREWS (8F) into the LEGS (J2, L2 M2, O2, and P2). å NOTE: Be sure to turn CAM SCREWS into both surfaces of the LEGS on the RIGHT END. 8F (8 used) L M2 S HI urfa DD ce EN wi CA th M S A2 L2 S HI urfa DD ce EN wi CA th M S B J2 S HI urfa DD ce EN wi CA th M S S HI urfa DD ce EN wi CA tho M ut S A2 C O2 P2 www.sauder.
Step 8 å Fasten the VALANCES (R) to the LEGS (J2, L2, O2, and P2) on the ENDS (A2 and C). Tighten four HIDDEN CAMS. 1 2 P2 L2 O2 Edge without CAM DOWELS ith e w AMS c a f Sur EN C C HIDD R Page 12 Sur R Sur Edge without CAM DOWELS fac e with fac e with HID DEN CA J2 MS A2 out HID DEN CA ith e w AMS c a f Sur DEN C D HI MS 415910 www.sauder.
Step 9 å First, fill the hole in the BRACE (G) 1/4 to 1/2 full with GLUE (54M). Then, insert the WOOD DOWEL (15F) into the hole. Wipe away the excess GLUE. å Fasten the BRACE (G) to the RIGHT END (A2). Use a BLACK 1-15/16" FLAT HEAD SCREW (113S). å Fasten the BRACE (G) to the STRETCHER (H). Use a TIE PLATE (3G) and two BLACK 9/16" LARGE HEAD SCREWS (1S). ! Caution Inspect the parts thoroughly before assembling. Disassembly of glued parts is extremely difficult.
Step 10 å Fasten the BACK (F) to the RIGHT REAR LEG (L2) on the RIGHT END (A2). Tighten two HIDDEN CAMS. L2 The BACK MOLDING should be here. A2 F Sur f HID ace wi DEN th CA MS Page 14 415910 www.sauder.
Step 11 å å Slide the BASE (Q) onto the notched edge of the BOTTOM (E). Now might be a good time to refresh your drink. *U.S. Patent No. 5,499,886 Notched edge Slide the BASE (Q) onto the notched edge. E www.sauder.
Step 12 å NOTE: You will need someone's help to hold the BOTTOM (E) until it is attached to the LEFT END (B) in the next step. å Fasten the BOTTOM (E) to the RIGHT END (A2). Tighten two HIDDEN CAMS. With someone's help, hold the BOTTOM (E) until it is attached to the LEFT END (B) in the next step. th S wi AM ce C rfa EN Su IDD H E Q A2 Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 13 å Fasten the LEFT END (B) and LEFT REAR LEG (M2) to the BOTTOM (E) and BACK (F). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees E M2 F B ut itho S w e fac AM Sur DEN C HID www.sauder.
Step 14 å å å NOTE: You will need someone's help in this step. Maximum 210 degrees Carefully lay your assembly onto the TOP (D). Fasten the ENDS (A2, B, and C) and VALANCES (R) to the TOP (D). Tighten ten HIDDEN CAMS. Arrow Minimum 190 degrees R C A2 R B ce rfa Su D th wi s le ho Page 18 415910 www.sauder.
Step 15 å Fasten two HINGES (14H) to the DOOR (I). Use four BLACK 1/2" FLAT HEAD SCREWS (11S). I 14H 11S BLACK 1/2” FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 16 å å Carefully stand your unit upright. å Fasten the DOOR (I) to the LEFT END (B) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. å Fasten two KNOBS (95K) to the DOOR (I). Use two BLACK 7/8" MACHINE SCREWS (37S). å å Push the DOOR STOP (4I) into the hole in the RIGHT END (A2). Pro Tip: Lift with your legs. And, you know, your arms.
Step 17 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 18 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D969 D132 D132 S D138 S D138 Groove å Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Insert the DRAWER SIDES (D132 and D138) at an angle into the slot at each end of the DRAWER FRONT (S).
Step 19 å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D132 and D138). å Fasten a DRAWER RIGHT (40CC) to the RIGHT DRAWER SIDE (D132) and a DRAWER LEFT (40CD) to the LEFT DRAWER SIDE (D138). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE.
Step 20 å Fasten two KNOBS (95K) to the DRAWER FRONT (S). Use two BLACK 7/8" MACHINE SCREWS (37S). Almost time to celebrate! With a nap. 37S BLACK 7/8" MACHINE SCREW (2 used in this step) S 95K Page 24 415910 www.sauder.
Step 21 å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. 60 lbs. 20 lbs. 40 lbs. www.sauder.
Step 22 å To make adjustments to the drawers, loosen SCREW #4 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
415910 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 (SUITE) Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. REMARQUE : Lorsque l’on enfonce les PROFILÉS EN I, il faudra alterner en enfonçant un PROFILÉ EN I dans l’extrémité supérieure et ensuite, en enfonçant dans l’extrémité inférieure jusqu’à ce qu’ils soient tous insérés dans les PIEDS. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol.
ÉTAPE 12 ÉTAPE 17 (SUITE) REMARQUE : Il faudra l’aide d’une autre personne pour tenir le DESSOUS (E) jusqu’à ce qu’il soit attaché à l’EXTRÉMITÉ GAUCHE (B) à l’étape suivante. Pour ajuster les PORTES de haut en bas (verticalement), desserrer les deux vis de réglage. Déplacer les PORTES verticalement à l'emplacement désiré. Serrer les vis après avoir ajusté. Fixer le DESSOUS (E) à l’EXTRÉMITÉ DROITE (A2). Serrer deux EXCENTRIQUES ESCAMOTABLES. Attention: Risque des dégâts ou blessures.
415910 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 (CONTINUACIÓN) No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. NOTA: Al golpear los SOPORTES EN I, tendrá que alternar, golpeando un SOPORTE EN I en el extremo superior y después una en el extremo inferior, hasta que todas se insertan en las PATAS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje veintidós EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A2, B y C), del FONDO (E), del DORSO (F) y de las CORNISAS (R).
PASO 12 PASO 17 (CONTINUACIÓN) NOTA: Necesitará la ayuda de alguien para sujetar el FONDO (E) hasta que se una al EXTREMO IZQUIERDO (B) en el siguiente paso. Para ajustar las PUERTAS hacia arriba o hacia abajo (vertical), afloje los dos tornillos de ajuste. Mueva las PUERTAS hacia arriba o hacia abajo a la ubicación deseada. Apriete los tornillos después de hacer los ajustes. Fije el FONDO (E) al EXTREMO DERECHO (A2). Apriete dos EXCÉNTRICOS ESCONDIDOS. Precaución: Riesgo de daños o heridas.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
