sauder.com Entertaining what entertains you. Entertainment Credenza Harbor View Collection | 415055 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 362633 06/27/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Not actual size Skip the power trip. This time. 27 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 24E FOOT BASE - 2 25E FOOT - 2 27G ANGLE BRACKET - 10 4L 1F HIDDEN CAM - 18 13H HINGE - 4 WARNING LABEL - 1 1N 4I 1R NAIL - 33 2F CAM DOWEL - 18 99K KNOB SET - 2 DOOR STOP - 1 METAL PIN - 12 23F FOOT SCREW - 2 2R RUBBER SLEEVE - 12 WARNING Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push eighteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHTS (C and D), TOP (E), and BOTTOM (F). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow 2F (18 used) 1F F E Arrow 1F 2F D Arrow C B Arrow A 1F 2F www.
Step 2 å å Fasten two ANGLE BRACKETS (27G) to each END (A and B) and three ANGLE BRACKETS (27G) to each VALANCE (L and M). Use ten BLACK 9/16" LARGE HEAD SCREWS (1S). Remember: Righty tighty. Lefty loosey. NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS (A and B) and VALANCES (L and M). 27G 1S BLACK 9/16" LARGE HEAD SCREW (10 used for the BRACKETS) M L 27G 27G 27G B A 27G Page 6 415055 www.sauder.
Step 3 å Fasten the STOP MOLDING (R) to the TOP (E). Tighten six HIDDEN CAMS. These surfaces should be even. S ith M w A ce C fa EN ur D S ID H E R Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 4 å Fasten the UPRIGHTS (C and D) to the TOP (E). Tighten four HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. C with S e c fa AM Sur EN C D HID D ut itho w S e fac AM Sur EN C D HID Finished edge Maximum 210 degrees R S ith M w A ce C fa EN ur D S ID H E Arrow Minimum 190 degrees Page 8 415055 www.sauder.
Step 5 å Fasten the BOTTOM (F) to the UPRIGHTS (C and D). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S These holes must be here. BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) S ith M w A ce C fa EN ur D S ID H F C D www.sauder.
Step 6 å Fasten the ENDS (A and B) to the TOP (E) and BOTTOM (F). Tighten eight HIDDEN CAMS. Edge with ANGLE BRACKETS A ith e w MS c a f A Sur EN C D HID F E B ut itho w S e fac AM Sur EN C D HID Maximum 210 degrees Edge with ANGLE BRACKETS Arrow Minimum 190 degrees Page 10 415055 www.sauder.
Step 7 Fasten the VALANCES (L and M) to the ENDS (A and B), UPRIGHTS (C and D), and TOP (E). Use six BLACK 9/16" LARGE HEAD SCREWS (1S) through the ANGLE BRACKETS and into the holes on the ENDS, UPRIGHTS, and TOP. å å å Don't worry. It isn't Rome. This can be built in a day. NOTE: Be sure to position the VALANCES as shown. Push a DOOR STOP (4I) into the hole in the TOP (E). Wider edge A Wider edge C E L D B 4I M 1S BLACK 9/16" LARGE HEAD SCREW (6 used for the BRACKETS) www.sauder.
Step 8 å Fasten the END MOLDINGS (Q) to the ENDS (A and B). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the ANGLE BRACKETS on the ENDS and into the END MOLDINGS. å NOTE: There are no pre-drilled holes in the END MOLDINGS. The SCREWS will tighten into the groove. 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the BRACKETS) A Q B Q Page 12 415055 www.sauder.
Step 9 å å å å Fasten the SKIRT (N) to the BOTTOM MOLDING (P). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). å NOTE: Do not overtighten the FOOT SCREWS. Fasten the BOTTOM MOLDING (P) to the BOTTOM (F). Use five BLACK 1-1/8" PAN HEAD SCREWS (9S). Carefully turn two FOOT SCREWS (23F) a few turns into the BOTTOM MOLDING (P). Next, turn a FOOT (O) onto the other end of each FOOT SCREW (23F). Turn the FEET clockwise until the FOOT SCREW is tight in the BOTTOM MOLDING (P) and each FOOT.
Step 10 å Carefully turn your unit over onto its front edges. Unfold the BACK (G) and lay it over your unit. å Fasten the top edge of the BACK (G) to your unit using thirteen BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the remaining BACK (G) to your unit using the NAILS (1N). å NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHTS (C and D). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed.
Step 11 å Fasten the HINGES (13H) to the DOORS (H and I). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). 13H 11S BLACK 1/2" FLAT HEAD SCREW (8 used in this step) I H 13H www.sauder.
Step 12 å å Carefully stand your unit upright. å IMPORTANT: The ADJUSTABLE FEET should not extend beyond the bottom edges of the ENDS (A and B). å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten the LEFT DOOR (I) to the LEFT UPRIGHT (D) as shown in the lower diagram. Use the screws in the HINGES.
Step 13 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 14 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHTS (C and D). Set the ADJUSTABLE SHELVES (J and K) onto the METAL PINS. å Apply the WARNING LABEL (4L) to the TOP (E). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram.
Crédence télévision/ vidéo/stéréo 415055 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. • Vérifier la taille et le poids du téléviseur.
ÉTAPE 10 ÉTAPE 13 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (G) et le placer sur l'élément. Fixer le chant supérieur de l'ARRIÈRE (G) à l'élément en utilisant treize VIS TÊTE LARGE 14 mm NOIRES (1S). Fixer l'autre ARRIÈRE (G) à l'élément à l'aide des CLOUS (1N).
415055 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 4 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. • Verifique el tamaño y peso del televisor.
PASO 10 PASO 13 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (G) y colóquelo sobre la unidad. Fije el borde superior del DORSO (G) a la unidad utilizando trece TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Fije el otro DORSO (G) a la unidad utilizando los CLAVOS (1N).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
