sauder.com Sweet stand. Sweet dreams. Night Stand Harbor View Collection | 415004 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-19 Français pg 20-22 Español pg 23-25 Lot # 367871 01/14/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-19 Hammer Français 20-22 Español 23-25 Safety 26 Warranty 27 Page 2 Not actual size Skip the power trip. This time. 415004 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Insert a CONNECTOR SCREW (8S) into each HIDDEN CONNECTOR (9F). 9F 8S Step 2 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Use your hammer to tap four HIDDEN CONNECTORS (9F) with SCREWS into the BRACE (E). 9F E 9F www.sauder.
Step 3 å Push seven HIDDEN CAMS (1F) into the BOTTOM (D), BRACE (E), and DRAWER BRACE (H). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow 2F (7 used) (7 used) 1F D Arrow E H Arrow 1F Insert the metal end of the CAM DOWEL into the HIDDEN CAM. 2F Page 6 415004 www.sauder.
Step 4 å Fasten the CABINET RIGHT (40CA) and CABINET LEFT (40CB) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å Fasten four ANGLE BRACKETS (27G) to the ENDS (A and B). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS. Remember: Righty tighty. Lefty loosey.
Step 5 å Tap two MOLDING CONNECTORS (16F) into the notches in the MOLDINGS (L, M, and N). Use your hammer to tap the MOLDING CONNECTORS (16F) into the notches in the MOLDINGS. Flat end Flat end 16F 16F 16F N M L Page 8 415004 www.sauder.
Step 6 å First, fasten the SKIRT (K) to the BOTTOM MOLDING (I). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Then, fasten the BOTTOM MOLDING (I) to the BOTTOM (D). Use four SILVER 1-1/4" PAN HEAD SCREWS (45S). Rounded edge 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) ed h is n Fi Un fin ish I ed su rfa ce e ac rf su K Rounded edge K 45S SILVER 1-1/4" PAN HEAD SCREW (4 used for the BOTTOM MOLDING) www.sauder.com/services These holes must be here.
Step 7 å Fasten the ENDS (A and B) to the BOTTOM (D). Tighten four HIDDEN CAMS. Finished edge B I Finished edge e ac les f r Su h ho wit D Sur fac ew ith HID DEN CA MS Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 10 A les ho t u ho t i ew ac f r Su Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 415004 www.sauder.
Step 8 å Fasten the MOLDINGS (M and N) to the ENDS (A and B). Use four BLACK 2-1/4" FLAT HEAD SCREWS (26S). 26S BLACK 2-1/4" FLAT HEAD SCREW (4 used in this step) Finished surface Finished surface L N B M A www.sauder.
Step 9 å Fasten the TOP (C) to the MOLDINGS (L, M, and N). Use seven BLACK 1-5/8" PAN HEAD SCREWS (27S). 27S BLACK 1-5/8" PAN HEAD SCREW (7 used for the MOLDINGS) Long rounded edge L B C Su r wit face hh ole s N M A Page 12 415004 www.sauder.
Step 10 å å Fasten the BRACE (E) to the ENDS (A and B). Tighten four HIDDEN CONNECTORS. Now might be a good time to refresh your drink. Fasten the BRACE MOLDING (J) to the BRACE (E). Tighten two HIDDEN CAMS. How to use the HIDDEN CONNECTOR To fasten two parts together using the HIDDEN CONNECTORS, insert your screwdriver, at an angle, into the slot in the HIDDEN CONNECTOR. While pushing the screw into the hole of the adjoining part, turn the screwdriver clockwise to tighten.
Step 11 å Fasten the END MOLDINGS (O) to the ENDS (A and B). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the ANGLE BRACKETS on the ENDS and into the END MOLDINGS. å NOTE: There are no pre-drilled holes in the END MOLDINGS. The SCREWS will tighten into the grooves. å Carefully turn two FOOT SCREWS (23F) a few turns into the BOTTOM MOLDING (I). å Next, turn a FOOT (P) onto the other end of each FOOT SCREW (23F).
Step 12 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it “square”. å Fasten the BACK (F) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 1N NAIL (20 used in this step) ed ish fin Un ce rfa su F www.sauder.
Step 13 1 VIEW THE T-LOCK BOX VIDEO 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D24 D723 D24 D25 G G Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å D25 Insert the DRAWER SIDES (D24 and D25) at an angle into the slot at each end of the DRAWER FRONT (G).
Step 14 å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D24 and D25). å Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD) to the DRAWER SIDES (D24 and D25). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #2 and #4. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Fasten the PULL (98K) to the DRAWER FRONT (G).
Step 15 å å Carefully stand your unit upright. If you're doing this to help a friend, don't leave without a bite. To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. 40 lbs. 15 lbs. 30 lbs. Page 18 Place the roller on the SLIDE behind the roller on the RAIL. 415004 www.sauder.
Step 16 å To make adjustments to the drawers, loosen SCREW #4 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
415504 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Insérer une VIS DE CONNECTEUR (8S) dans chaque CONNECTEUR ESCAMOTABLE (9F). Fixer la PLINTHE (K) à la MOULURE DE DESSOUS (I). Utiliser deux VIS TÊTE PLATE 48 mm NOIRES (2S). ÉTAPE 2 Ensuite, fixer la MOULURE DE DESSOUS (I) au DESSOUS (D). Utiliser quatre VIS TÊTE GOUTTE DE SUIF 32 mm ARGENTÉES (45S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol.
ÉTAPE 11 ÉTAPE 14 Fixer les MOULURES D'EXTRÉMITÉ (O) aux EXTRÉMITÉS (A et B). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (1S) à travers les CONSOLES À ÉQUERRE situées sur les EXTRÉMITÉS, et dans les MOULURES D'EXTRÉMITÉ. Insérer une EXCENTRIQUE DE COULISSE (10A) dans les CÔTÉS DE TIROIR (D24 et D25). REMARQUE : Les MOULURES D'EXTRÉMITÉ ne comportent pas de trous pré-percés. Serrer les VIS dans les rainures.
415004 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 Inserte un TORNILLO CONECTOR (8S) dentro de cada CONECTOR INVISIBLE (9F). Primero, fije el FALDÓN (K) a la MOLDURA DE FONDO (I). Utilice dos TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (2S). PASO 2 A continuación, fije la MOLDURA DE FONDO (I) al FONDO (D). Utilice cuatro TORNILLOS PLATEADOS DE CABEZA REDONDA de 32 mm (45S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso.
PASO 11 PASO 14 Fije las MOLDURAS DE EXTREMO (O) a los EXTREMOS (A y B). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S) a través de los SOPORTES ANGULARES sujetados a los EXTREMOS y dentro de las MOLDURAS DE EXTREMO. Inserte un EXCÉNTRICO DE CORREDERA (10A) dentro de los LADOS DE CAJÓN (D24 y D25). NOTA: No hay agujeros perforados en las MOLDURAS DE EXTREMO. Los TORNILLOS apretarán dentro de las ranuras.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves. Place the heavier items on the lower shelves.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
