sauder.com Your center of attention. Entertainment Credenza Barrister Lane Collection | 414958 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 374470 06/24/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Not actual size Skip the power trip. This time. 27 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F 23E FOOT - 2 10F TWIST-LOCK® FASTENER - 2 27H HINGE - 4 3L WARNING LABEL - 1 CAM DOWEL - 12 2F HIDDEN CAM - 24 17G METAL BRACKET - 6 8F CAM SCREW - 12 31G CORNER BRACKET - 4 2I MAGNETIC CATCH - 2 6I STRIKE PLATE - 2 1N NAIL - 46 1R METAL PIN - 12 69K KNOB - 2 2R RUBBER SLEEVE - 12 WARNING Never use this furniture with a TV that is too large or too heavy.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twenty-four HIDDEN CAMS (1F) into the ENDS (A), UPRIGHTS (B and C), TOP (D) and BOTTOM (E). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except in the five edges called out below. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Turn twelve CAM SCREWS (8F) into the BASES (K and L), MOLDINGS (N and O), and STOP MOLDING (P). Remember: Righty tighty. Lefty loosey. O N L K P 8F Page 6 414958 www.sauder.
Step 3 å Push two SAUDER TWIST-LOCK® FASTENERS (10F) into the large holes in the MOLDINGS (N and O). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F N O www.sauder.
Step 4 å å Fasten the MOLDINGS (N and O) to the TOP (D). Tighten two TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. Fasten the STOP MOLDING (P) to the TOP (D). Tighten four HIDDEN CAMS. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 5 å Fasten three METAL BRACKETS (17G) to the STOP MOLDING (P). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten two CORNER BRACKETS (31G) to the TOP (D), STOP MOLDING (P), and MOLDINGS (N and O). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). å Now, fasten the FRONT MOLDING (M) to the CORNER BRACKETS (31G) and METAL BRACKETS (17G). Use seven BLACK 9/16" LARGE HEAD SCREWS (1S). 1S BLACK 9/16" LARGE HEAD SCREW (18 used in this step) 31G N 17G D Curved edge M P O Wide edge 31G www.
Step 6 å å Fasten the UPRIGHTS (B and C) to the TOP (D). Tighten four HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day. Push two MAGNETIC CATCHES (2I) into the large holes in the UPRIGHTS (B and C). 2I B out h t i ew S fac CAM r u S DEN HID C withMS e c fa A Sur DEN C HID D Finished edge 2I Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 7 å Fasten the END MOLDINGS (Q) to the ENDS (A). Tighten four HIDDEN CAMS. å Fasten the BASES (K and L) to the ENDS (A) as shown. Tighten four HIDDEN CAMS. å NOTE: The END (A) on the left will be called the LEFT END and the END (A) on the right will be called the RIGHT END. Maximum 210 degrees Arrow Minimum 190 degrees These holes must be closest to the top edge. S HI urfa DD ce EN wi CA th M S Sur fac ew ith hol es The four small holes must be closest to the top edge.
Step 8 å Fasten the RIGHT END (A) to the RIGHT MOLDING (N). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (E) to the RIGHT BASE (K). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Maximum 210 degrees Minimum 190 degrees K A S ith M w A ce C fa EN ur D S ID H RIGHT END Arrow E N These holes must be here. Page 12 414958 www.sauder.
Step 9 å Fasten the BOTTOM (E) to the UPRIGHTS (B and C). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Fasten the LEFT END (A) to the LEFT MOLDING (O). Tighten two HIDDEN CAMS. å Fasten the LEFT BASE (L) to the BOTTOM (E). Tighten two HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) E B L C LEFT END A O www.sauder.
Step 10 å Fasten three METAL BRACKETS (17G) to the BOTTOM (E). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten two CORNER BRACKETS (31G) to the BOTTOM (E) and BASES (K and L). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the BASE (J) to the BRACKETS (17G) on the BOTTOM (E) and BASES (K and L). Use seven BLACK 9/16" LARGE HEAD SCREWS (1S). 1S BLACK 9/16" LARGE HEAD SCREW (18 used in this step) 31G K 17G E Curved edge J L 31G Unfinished edge Page 14 414958 www.sauder.
Step 11 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHTS (B and C).
Step 12 å Fasten the HINGES (27H) to the DOORS (G). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the STRIKE PLATES (6I) to the DOORS (G). Use two BLACK 1/2" FLAT HEAD SCREWS (11S). 1S BLACK 9/16" LARGE HEAD SCREW (8 used for the HINGES) 27H 11S BLACK 1/2" FLAT HEAD SCREW (2 used for the STRIKE PLATES) 6I 6I G This will be the LEFT DOOR (G) in the next step. G 27H This will be the RIGHT DOOR (G) in the next step. Page 16 414958 www.sauder.
Step 13 å NOTE: You may need help from another person to complete this step. å å Carefully stand your unit upright. å Fasten a KNOB (69K) to the RIGHT DOOR (G). Use a BLACK 1-1/8" MACHINE SCREW (21S). å Repeat this step fastening the LEFT DOOR (G) to the END MOLDING (Q) on the LEFT END (A). Pro Tip: Lift with your legs. And, you know, your arms. Fasten the RIGHT DOOR (G) to the END MOLDING (Q) on the RIGHT END (A). Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 14 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A) and UPRIGHTS (B and C). Set the ADJUSTABLE SHELVES (H and I) onto the METAL PINS. å Apply the WARNING LABEL (3L) to the TOP (D). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram.
Crédence télévision/ vidéo/stéréo 414958 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Fixer les MOULURES (N et O) au DESSUS (D). Serrer deux FIXATIONS TWIST-LOCK®. • Vérifier la taille et le poids du téléviseur.
ÉTAPE 8 ÉTAPE 12 Attention : Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Fixer les CHARNIÈRES (27H) aux PORTES (G). Utiliser huit VIS TÊTE LARGE 14 mm NOIRES (1S). Fixer l’EXTRÉMITÉ DROITE (A) à la MOULURE DROITE (N). Serrer deux EXCENTRIQUES ESCAMOTABLES. Fixer les PLAQUES DE BUTÉE (6I) aux PORTES (G). Utiliser deux VIS TÊTE PLATE 13 mm NOIRES (11S). Fixer le DESSOUS (E) au SOCLE DROIT (K). Serrer deux EXCENTRIQUES ESCAMOTABLES.
414958 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 4 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Fije las MOLDURAS (N y O) al PANEL SUPERIOR (D). Apriete dos SUJETADORES TWIST-LOCK®. • Verifique el tamaño y peso del televisor.
PASO 8 PASO 12 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije las BISAGRAS (27H) a las PUERTAS (G). Utilice ocho TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Fije el EXTREMO DERECHO (A) a la MOLDURA DERECHA (N). Apriete dos EXCÉNTRICOS ESCONDIDOS. Fije las PLACAS DE CONTACTO (6I) a las PUERTAS (G). Utilice dos TORNILLOS NEGROS DE CABEZA PERDIDA de 13 mm (11S). Fije el FONDO (E) a la BASE DERECHA (K).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
