sauder.com Smart stand for the idiot box. Corner TV Stand Barrister Lane Collection | 414729 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-24 Français pg 25-28 Español pg 29-32 Lot # 368865 02/03/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-24 Hammer Français 25-28 Español 29-32 Safety 33-34 Warranty Not actual size Skip the power trip. This time. 35 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 23E FOOT - 1 1F HIDDEN CAM - 20 1G SAFETY BRACKET - 1 2I MAGNETIC CATCH - 1 4G METAL BRACKET - 4 6I CAM DOWEL - 12 2F 8F 27G ANGLE BRACKET - 10 DECORATIVE 69K KNOB - 1 STRIKE PLATE - 1 ® 10F TWIST-LOCK FASTENER - 3 CAM SCREW - 8 31G CORNER BRACKET - 4 1L 27H HINGE - 2 WARNING LABEL - 1 3M ANTI-SKID PAD - 1 WARNING Never use this furniture with a TV that is too large or too heavy.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the MOLDINGS (M and N) and SMALL UPRIGHT (D). Do not tighten the TWIST-LOCK® FASTENERS in this step. D 10F M N www.sauder.
Step 2 å Push twenty HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), BOTTOM (F), and SHELF (G). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except the short edges of the ENDS (A and B). Do not tighten the HIDDEN CAMS in this step. Arrow 2F (12 used) (20 used) F 1F G Do not insert CAM DOWELS into these edges. C Arrow B A Insert the metal end of the CAM DOWEL into the HIDDEN CAM.
Step 3 å Fasten ten ANGLE BRACKETS (27G) to the ENDS (A and B) and SHELF (G). Use ten BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS and SHELF. å Fasten the SMALL END MOLDINGS (R) to the ENDS (A and B). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: The SMALL END MOLDINGS do not have holes. Turn the screws into the grooves of the MOLDINGS. Do not over tighten. Some assembly (and snacks) required.
Step 4 å Turn eight CAM SCREWS (8F) into the MOLDINGS (M and N) and BASES (P and Q). (8 used) 8F Q P M N Page 8 414729 www.sauder.
Step 5 å Fasten the RIGHT BASE (P) to the RIGHT END (A). Tighten two HIDDEN CAMS. å Fasten the LEFT BASE (Q) to the LEFT END (B). Tighten two HIDDEN CAMS. 1 2 A su rf ac e Angled edge P U n fin is h ed su rf ac e U n fin is h ed B Q Angled edge www.sauder.
Step 6 å Fasten the MOLDINGS (M and N) to the TOP (E). Tighten two TWIST-LOCK® FASTENERS. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible. Dowel end N E M Page 10 414729 www.sauder.
Step 7 å Fasten two CORNER BRACKETS (31G) to the MOLDINGS (M and N) and TOP (E). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten two METAL BRACKETS (4G) to the TOP (E). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the FRONT MOLDING (U) to the CORNER BRACKETS (31G) and METAL BRACKETS (4G). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). 1S BLACK 9/16" LARGE HEAD SCREW (16 used in this step) 31G N 4G E U M 31G www.sauder.
Step 8 å Fasten the LEFT END (B) to the LEFT MOLDING (N). Tighten two HIDDEN CAMS. å Fasten the SMALL UPRIGHT (D) to the TOP (E). Tighten the TWIST-LOCK® FASTENER. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. B Sur HIDface w DEN ith CA MS Surface with TWIST-LOCK® FASTENER D N E Page 12 414729 www.sauder.
Step 9 å Fasten the SHELF (G) to the LEFT END (B). Tighten two HIDDEN CAMS. å Fasten the SHELF (G) to the SMALL UPRIGHT (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) B G Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 10 å Fasten the UPRIGHT (C) to the SHELF (G). Tighten two HIDDEN CAMS. å Fasten the SHELF MOLDING (S) to the SHELF (G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). Maximum 210 degrees Arrow Minimum 190 degrees Don't worry. It isn't Rome. This can be built in a day. C Sur HIDface w DEN ith CA MS G S 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the SHELF MOLDING) These edges should be even. Page 14 414729 www.sauder.
Step 11 å Fasten the BOTTOM (F) to the LEFT BASE (Q). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (F) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Maximum 210 degrees Arrow Minimum 190 degrees 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) S H urf ID a D ce E w N i C th A M S Q F C www.sauder.
Step 12 å Fasten the RIGHT END (A) to the RIGHT MOLDING (M), SHELF (G), and BOTTOM (F). Tighten six HIDDEN CAMS. å Push the MAGNETIC CATCH (2I) into the hole in the UPRIGHT (C). Maximum 210 degrees Arrow Minimum 190 degrees F C G A 2I M Page 16 414729 www.sauder.
Step 13 å Fasten an END MOLDING (T) to the RIGHT END (A). Tighten two HIDDEN CAMS. å Fasten the other END MOLDING (T) to the LEFT END (B). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten two CORNER BRACKETS (31G) to the BASES (P and Q) and BOTTOM (F). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten two METAL BRACKETS (4G) to the BOTTOM (F). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the BRACKETS are even with the edges of the BOTTOM.
Step 14 å å Carefully turn your unit over onto its front edges. å Carefully insert the CROSS SHELF assembly into the opening as shown. Insert two LONG METAL PINS (3R) into the holes in the CROSS SHELF (H). Push two SMALL CROSS SHELVES (I) over the LONG METAL PINS. I I H Finished edge I I Finished edge H 3R Finished edge Page 18 414729 www.sauder.
Step 15 å å å Unfold the BACK (J) and lay it over your unit. å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. å Push the FOOT (23E) into the hole in the BOTTOM (F). Caution Fasten the BACK (J) to your unit using the NAILS (1N). Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHT (C), SMALL UPRIGHT (D), and SHELF (G).
Step 16 å Fasten the HINGES (27H) to the DOOR (K). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the STRIKE PLATE (6I) to the DOOR (K). Use a BLACK 1/2" FLAT HEAD SCREW (11S). 11S BLACK 1/2" FLAT HEAD SCREW (1 used for the STRIKE PLATE) 6I 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the HINGES) K 27H Page 20 414729 www.sauder.
Step 17 å å Carefully stand your unit upright. å Fasten the DECORATIVE ENDS (33M) to the DOOR (K). Use two SILVER 3/4" MACHINE SCREWS (20S). å Insert a DECORATIVE POST (32M) into the DECORATIVE ENDS. å Fasten the DECORATIVE BACKPLATE (34M) and DECORATIVE KNOB (69K) to the DOOR. Use a SILVER 1-1/2" MACHINE SCREW (95S). Pro Tip: Lift with your legs. And, you know, your arms. Fasten the DOOR (K) to the RIGHT END MOLDING (T). Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 18 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the END (A) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (L) onto the METAL PINS. å Apply the WARNING LABEL (1L) to the TOP (E). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram.
Step 19 å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. BLACK 1-7/8" FLAT HEAD SCREW (1 used into a stud in your wall) 2S 1G BLACK 9/16" LARGE HEAD SCREW (1 used into the top of your unit) 1S www.sauder.
Step 20 å To help prevent the TV from sliding, place the ANTI-SKID PAD (3M) under the front support of the TV or divide among the front supports if more than one. å å å Push a CAM COVER (36P) onto each HIDDEN CAM. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? 50 lbs. 3M 35 lbs. 25 lbs. 25 lbs. 25 lbs. 50 lbs.
414729 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 3 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Fixer dix CONSOLES À ÉQUERRE (27G) aux EXTRÉMITÉS (A et B) et à la TABLETTE (G). Utiliser dix VIS TÊTE LARGE 14 mm NOIRES (1S).
ÉTAPE 7 ÉTAPE 11 Fixer deux SUPPORTS EN CORNIÈRE (31G) aux MOULURES (M et N) et au DESSUS (E). Utiliser huit VIS TÊTE LARGE 14 mm NOIRES (1S). Fixer le DESSOUS (F) sur le SOCLE GAUCHE (Q). Serrer deux EXCENTRIQUES ESCAMOTABLES. Fixer deux CONSOLES EN MÉTAL (4G) au DESSUS (E). Utiliser deux VIS TÊTE LARGE 14 mm NOIRES (1S). Fixer la MOULURE AVANT (U) sur les SUPPORTS EN CORNIÈRE (31G) et aux CONSOLES EN MÉTAL (4G). Utiliser six VIS TÊTE LARGE 14 mm NOIRES (1S).
ÉTAPE 15 ÉTAPE 18 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Enfoncer les MANCHONS EN CAOUTCHOUC (2R) sur les GOUPILLES EN MÉTAL (1R). Insérer les GOUPILLES EN MÉTAL dans les trous choisis de l'EXTRÉMITÉ (A) et du MONTANT (C). Poser les TABLETTES RÉGLABLES (L) sur les GOUPILLES EN MÉTAL. Déplier l'ARRIÈRE (J) et le placer sur l'élément. Fixer l'ARRIÈRE (J) à l'élément à l'aide des CLOUS (1N).
414729 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 3 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Fije diez SOPORTES ANGULARES (27G) a los EXTREMOS (A y B) y al ESTANTE (G). Utilice diez TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S).
PASO 7 PASO 11 Fije dos MÉNSULAS DE ESQUINA (31G) a las MOLDURAS (M y N) y al PANEL SUPERIOR (E). Utilice ocho TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Fije el FONDO (F) a la BASE IZQUIERDA (Q). Apriete dos EXCÉNTRICOS ESCONDIDOS. Fije dos SOPORTES DE METAL (4G) al PANEL SUPERIOR (E). Utilice dos TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Fije la MOLDURA DELANTERA (U) a las MÉNSULAS DE ESQUINA (31G) y a los SOPORTES DE METAL (4G).
PASO 15 PASO 18 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Empuje los MANGUITOS DE GOMA (2R) sobre las ESPIGAS DE METAL (1R). Inserte las ESPIGAS DE METAL dentro de los agujeros al nivel preferido del EXTREMO (A) y del PARAL (C). Coloque los ESTANTES AJUSTABLES (L) sobre las ESPIGAS DE METAL. Desdoble el DORSO (J) y colóquelo sobre la unidad. Fije el DORSO (J) a la unidad utilizando los CLAVOS (1N).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
