414723 Corner TV Stand Barrister Lane Collection PLEASE CONTACT US BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English .................... Page 1-22 Français ...............Pages 23-25 Made in the USA Archbold, OH Espanol.............
TABLE OF CONTENTS ADULT ASSEMBLY REQUIRED Part Identification .......................3 Hardware Identification .............4 ASSEMBLY TOOLS REQUIRED Assembly Steps .................... 5-22 No. 2 Phillips Screwdriver Français .............................. 23-25 Tip Shown Actual Size Espanol............................... 26-28 Safety ................................. 29-30 Hammer Warranty ...................................31 WARNING Use of a TV that is too heavy or large is hazardous.
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts.
HARDWARE IDENTIFICATION 2F CAM DOWEL - 12 1F HIDDEN CAM - 20 23E FOOT - 1 8F CAM SCREW - 8 10F TWIST-LOCK® FASTENER - 3 1G SAFETY BRACKET - 1 4G METAL BRACKET - 4 27G ANGLE BRACKET - 10 31G CORNER BRACKET - 4 DECORATIVE 69K KNOB - 1 27H HINGE - 2 1L WARNING LABEL - 1 2I MAGNETIC CATCH - 1 3M ANTI-SKID PAD - 1 6I STRIKE PLATE - 1 DECORATIVE 32M POST - 2 WARNING Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur.
S p te Look for this icon. It means a video assembly tip is available at: www.sauder.com/services/tips 1 Do not tighten the TWIST-LOCK® FASTENERS in this step. D 10F M N Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the MOLDINGS (M and N) and SMALL UPRIGHT (D). 414723 www.sauder.
S p te 2 Do not tighten the HIDDEN CAMS in this step. Arrow 2F (12 used) (20 used) 1F F G Do not insert CAM DOWELS into these edges. Arrow 1F C Arrow B 1F Do not insert CAM DOWELS into this edge. A 2F Arrow Arrow 1F Do not insert CAM DOWELS into this edge. Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Push twenty HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), BOTTOM (F), and SHELF (G).
S p te 3 27G G The groove in the MOLDINGS (R) should be closer to the top edge. R These edges should be even. 27G (10 used in this step) A 1S B R BLACK 9/16" LARGE HEAD SCREW (14 used for the BRACKETS) 27G Fasten ten ANGLE BRACKETS (27G) to the ENDS (A and B) and SHELF (G). Use ten BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS and SHELF. Fasten the SMALL END MOLDINGS (R) to the ENDS (A and B).
S p te 4 Q P M N 8F (8 used) A ac e Angled edge P Q U n fi ni sh ed su rf ac e U n fi ni sh ed su rf B Angled edge Turn eight CAM SCREWS (8F) into the MOLDINGS (M and N) and BASES (P and Q). Fasten the RIGHT BASE (P) to the RIGHT END (A). Tighten two HIDDEN CAMS. Fasten the LEFT BASE (Q) to the LEFT END (B). Tighten two HIDDEN CAMS. Page 8 www.sauder.
S p te How to use the SAUDER TWIST-LOCK® FASTENER 5 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible. Dowel end N E M Fasten the MOLDINGS (M and N) to the TOP (E). Tighten two TWIST-LOCK® FASTENERS. 414723 www.sauder.
S p te 6 31G N 4G E U M 1S 31G BLACK 9/16" LARGE HEAD SCREW (16 used for the BRACKETS) Fasten two CORNER BRACKETS (31G) to the MOLDINGS (M and N) and TOP (E). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten two METAL BRACKETS (4G) to the TOP (E). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the FRONT MOLDING (U) to the CORNER BRACKETS (31G) and METAL BRACKETS (4G). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). Page 10 www.sauder.
S p te 7 B Sur f HIDace w DE ith NC AM S Surface with TWIST-LOCK® FASTENER D N E Fasten the LEFT END (B) to the LEFT MOLDING (N). Tighten two HIDDEN CAMS. Fasten the SMALL UPRIGHT (D) to the TOP (E). Tighten the TWIST-LOCK® FASTENER. 414723 www.sauder.
S p te 8 B 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) G S H urf ID a c D e E w N it C h A M S D Fasten the SHELF (G) to the LEFT END (B). Tighten two HIDDEN CAMS. Fasten the SHELF (G) to the SMALL UPRIGHT (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Caution Risk of damage or injury. Hidden Cams must be completely tightened. Hidden Cams that are not completely tightened may loosen, and parts may separate.
S p te 9 Maximum 210 degrees Minimum 190 degrees Arrow C Sur f HIDace w DE ith NC AM S G S 1S These edges should be even. BLACK 9/16" LARGE HEAD SCREW (4 used for the SHELF MOLDING) Fasten the UPRIGHT (C) to the SHELF (G). Tighten two HIDDEN CAMS. Fasten the SHELF MOLDING (S) to the SHELF (G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 414723 www.sauder.
S p te 10 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) S H urf ID a c D e E w N it C h A M F S Q C Maximum 210 degrees Arrow Minimum 190 degrees Fasten the BOTTOM (F) to the LEFT BASE (Q). Tighten two HIDDEN CAMS. Tighten the BOTTOM (F) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Page 14 www.sauder.
S p te 11 F C G A 2I M Maximum 210 degrees Arrow Minimum 190 degrees Fasten the RIGHT END (A) to the RIGHT MOLDING (M), SHELF (G) and BOTTOM (F). Tighten six HIDDEN CAMS. Push the MAGNETIC CATCH (2I) into the hole in the UPRIGHT (C). 414723 www.sauder.
S p te 12 31G 4G Q These edges should be even. 31G F O P B T A Use the small holes in this MOLDING (T). T Maximum 210 degrees Arrow Minimum 190 degrees 1S These edges should be even. BLACK 9/16" LARGE HEAD SCREW (18 used in this step) Fasten an END MOLDING (T) to the RIGHT END (A). Tighten two HIDDEN CAMS. Fasten the other END MOLDING (T) to the LEFT END (B). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten two CORNER BRACKETS (31G) to the BASES (P and Q) and BOTTOM (F).
S p te 13 I H Finished edge I I Finished edge 3R I H Finished edge Carefully turn your unit over onto its front edges. Insert two LONG METAL PINS (3R) into the holes in the CROSS SHELF (H). Push two SMALL CROSS SHELVES (I) over the LONG METAL PINS. Carefully insert the CROSS SHELF assembly into the opening as shown. 414723 www.sauder.
S Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. p te 14 These holes must line up over the URIGHT (C), SMALL UPRIGHT (D), and SHELF (G). The BACK should be against the bottom surface of the TOP. U n fi ni sh ed su rf ac e J F 23E 1N NAIL (45 used in this step) Unfold the BACK (J) and lay it over your unit. Fasten the BACK (J) to your unit using the NAILS (1N).
S p te 15 6I 11S BLACK 1/2" FLAT HEAD SCREW (1 used for the STRIKE PLATE) K 27H 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the HINGES) Fasten the HINGES (27H) to the DOOR (K). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the STRIKE PLATE (6I) to the DOOR (K). Use a BLACK 1/2" FLAT HEAD SCREW (11S). 414723 www.sauder.
S p te 16 33M 69K 32M 34M 1S 95S SILVER 1-1/2"" MACHINE SCREW (1 used for the BACKPLATE and KNOB) BLACK 9/16" LARGE HEAD SCREW (4 used for the HINGES) 32M 33M T 20S K SILVER 3/4" MACHINE SCREW (2 used for the DECORATIVE ENDS Carefully stand your unit upright. Fasten the DOOR (K) to the RIGHT END MOLDING (T). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the DECORATIVE ENDS (33M) to the DOOR (K). Use two SILVER 3/4" MACHINE SCREWS (20S).
S p te WARNING 17 Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur. The TV and furniture will be unstable and may tip. BLACK 1-7/8" FLAT HEAD SCREW (1 used into a stud in your wall) - The TV must weigh less than 50 lbs. - The base of the TV must be able to sit completely on this shelf. 2S 1G BLACK 9/16" LARGE HEAD SCREW (1 used into the top of your unit) 1S 1L E A L L C 1R 2R (8 used) Push the RUBBER SLEEVES (2R) over the METAL PINS (1R).
S p te 18 50 lbs. 3M 35 lbs. 25 lbs. 25 lbs. 25 lbs. 50 lbs. 36P (8 used) To cover HIDDEN CAMS To help prevent the TV from sliding, place the ANTI-SKID PAD (3M) under the front support of the TV or divide among the front supports if more than one. Push a CAM COVER (36P) onto each HIDDEN CAM. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. Page 22 www.sauder.
414723 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 5 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Utilisation de la FIXATION TWIST-LOCK® SAUDER • Vérifier la taille et le poids du téléviseur.
ÉTAPE 11 ÉTAPE 15 Fixer l'EXTRÉMITÉ DROITE (A) à la MOULURE DROITE (M), à la TABLETTE (G) et au DESSOUS (F). Serrer six EXCENTRIQUES ESCAMOTABLES. Fixer les CHARNIÈRES (27H) à la PORTE (K). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (1S). Enfoncer le LOQUETEAU MAGNÉTIQUE (2I) dans le trou du MONTANT (C). Fixer une PLAQUE DE BUTÉE (6I) à la PORTE (K). Utiliser une VIS TÊTE PLATE 13 mm NOIRE (11S). ÉTAPE 16 ÉTAPE 12 Relever, avec précaution, l'élément dans sa position verticale.
Mueble Televisión rinconero 414723 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 4 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Atornille ocho BIELAS DE EXCÉNTRICO (8F) en las MOLDURAS (M y N) y las BASES (P y Q). • Verifique el tamaño y peso del televisor.
PASO 9 PASO 14 (CONTINUACIÓN) Fije el PARAL (C) al ESTANTE (G). Apriete dos EXCÉNTRICOS ESCONDIDOS. NOTA: Hay perforaciones provistas para el acceso a través del DORSO. Cuidadosamente corte los agujeros necesarios. Fije la MOLDURA DE ESTANTE (S) al ESTANTE (G). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Inserte la PATA (23E) dentro del agujero del FONDO (F). PASO 15 PASO 10 Fije el FONDO (F) a la BASE IZQUIERDA (Q). Apriete dos EXCÉNTRICOS ESCONDIDOS.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear valued customer: Thank you for your purchase from the Sauder family companies. It’s our pleasure to provide you with an affordable solution that meets your furniture and storage needs. I hope you will enjoy it for years to come. I am pleased with this company’s consistent ability to amaze the customer over time. My grandfather, Erie Sauder, founded the company in 1934 and later invented and patented the first commercially successful ready-to-assemble table.
