414721 Storage Credenza Barrister Lane Collection PLEASE CONTACT US BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English .................... Page 1-22 Français ...............Pages 23-25 Made in the USA Archbold, OH Espanol.............
TABLE OF CONTENTS ADULT ASSEMBLY REQUIRED Part Identification .......................3 Hardware Identification .............4 ASSEMBLY TOOLS REQUIRED Assembly Steps .................... 5-22 No. 2 Phillips Screwdriver Français .............................. 23-25 Tip Shown Actual Size Espanol............................... 26-28 Safety ................................. 29-30 Hammer Warranty ...................................31 WARNING Use of a TV that is too heavy or large is hazardous.
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts.
HARDWARE IDENTIFICATION 23E FOOT - 1 1F HIDDEN CAM - 24 1G SAFETY BRACKET - 1 2I SMALL MAGNETIC CATCH - 2 2F CAM DOWEL - 12 CAM SCREW - 12 8F 4G METAL BRACKET - 6 31G CORNER BRACKET - 4 STRIKE PLATE - 4 12I MAGNETIC CATCH - 2 6I 4L WARNING LABEL - 1 3M ANTI-SKID PAD - 1 DECORATIVE 33M END - 4 10F TWIST-LOCK® FASTENER - 2 27H HINGE - 8 DECORATIVE 69K KNOB - 2 DECORATIVE 34M BACKPLATE - 2 WARNING Never use this furniture with a TV that is too large or too heavy.
S p te Look for this icon. It means a video assembly tip is available at: www.sauder.com/services/tips 1 Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F O P Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the MOLDINGS (O and P). 414721 www.sauder.
S Do not tighten the HIDDEN CAMS in this step. p te 2 Arrow 2F (12 used) 1F (24 used) Arrow 2F 1F Do not insert CAM DOWELS into these parts. D T T Arrow 1F B Do not insert CAM DOWELS into these edges. A Arrow A Arrow 1F Do not insert CAM DOWELS into these edges. Insert the metal end of the CAM DOWEL into the HIDDEN CAM. 2F Push twenty-four HIDDEN CAMS (1F) into the ENDS (A), UPRIGHT (B), BOTTOM (D), and BRACES (T).
S p te 3 8F (12 used) N O P K L Turn twelve CAM SCREWS (8F) into the BASES (K and L) and MOLDINGS (N, O, and P). 414721 www.sauder.
S p te 4 This END (A) will now be called the RIGHT END (A). These holes must be here. Q This END (A) will now be called the LEFT END (A). S H urf ID a c D e E w N it C h A M S A K A Q S H urf ID a c D e E w N it C h A M S Angled edge L Angled edge Fasten the END MOLDINGS (Q) to the ENDS (A). Tighten four HIDDEN CAMS. Fasten the BASES (K and L) to the ENDS (A). Tighten four HIDDEN CAMS. Caution Risk of damage or injury. Hidden Cams must be completely tightened.
S p te 5 How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible. Dowel end P S ur fa ce w it h ho le s C O Long finished edge Fasten the MOLDINGS (O and P) to the TOP (C). Tighten two TWIST-LOCK® FASTENERS. 414721 www.sauder.
S p te 6 31G P 4G C N O 1S BLACK 9/16" LARGE HEAD SCREW (16 used for the BRACKETS) 31G Fasten two CORNER BRACKETS (31G) to the MOLDINGS (O and P) and TOP (C). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten two METAL BRACKETS (4G) to the TOP (C). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the FRONT MOLDING (N) to the TOP (C) and MOLDINGS (O and P). Use six BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS (4G) and CORNER BRACKETS (31G) and into the FRONT MOLDING.
S p te 7 Surface with HIDDEN CAMS 51S BLACK 9/16" PAN HEAD SCREW (4 used for the MAGNETIC CATCHES) 12I T Surface with HIDDEN CAMS N 2I T 2I Fasten the BRACES (T) to the FRONT MOLDING (N). Tighten four HIDDEN CAMS. Push a SMALL MAGNETIC CATCH (2I) into the center hole in each BRACE (T). Fasten a MAGNETIC CATCH (12I) to each BRACE (T). Use four BLACK 9/16" PAN HEAD SCREWS (51S). NOTE: Pay close attention to the positioning of the MAGNETIC CATCHES (12I). Follow the diagram. 414721 www.sauder.
S p te 8 R B ith S w M e fac N CA r u S DE HID N C 4G 1S Maximum 210 degrees BLACK 9/16" LARGE HEAD SCREW (2 used for the METAL BRACKETS) Arrow Minimum 190 degrees Fasten the UPRIGHT (B) to the TOP (C). Tighten two HIDDEN CAMS. Fasten the UPRIGHT (B) to the FRONT MOLDING (N). Use a METAL BRACKET (4G) and two BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the UPRIGHT MOLDING (R) to the UPRIGHT (B). Tighten two HIDDEN CAMS. Page 12 www.sauder.
S p te 9 L Q A ith S w M e fac N CA r u S DE HID F P Sur f wit ace h hol es C 1R Fasten the LEFT END (A) to the LEFT MOLDING (P). Tighten two HIDDEN CAMS. Insert two METAL PINS (1R) into the CENTER BACK (F). Insert the METAL PINS (1R) in the CENTER BACK (F) into the holes in the TOP (C). 414721 www.sauder.
S p te 10 2S BLACK 1-7/8" FLAT HEAD SCREW (3 used in this step) L These small holes must be here. A S B h M it A w C ce N fa E ur D S ID H D F Maximum 210 degrees Arrow Minimum 190 degrees Fasten the BOTTOM (D) to the LEFT BASE (L). Tighten two HIDDEN CAMS. Fasten the BOTTOM (D) to the UPRIGHT (B) and CENTER BACK (F). Use three BLACK 1-7/8" FLAT HEAD SCREWS (2S). Page 14 www.sauder.
S p te 11 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) D E Sur f wit ace h hol es Finished edge 1R E Finished edge C Sur f wit ace h hol es 1R Insert four METAL PINS (1R) into the TOP (C). Insert the METAL PINS (1R) in the TOP (C) into the holes in the BACKS (E). Fasten the BACKS (E) to the BOTTOM (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). 414721 www.sauder.
S p te 12 D K Q A t hou S t i w ace CAM f r Su DEN HID O Maximum 210 degrees Arrow Minimum 190 degrees Fasten the RIGHT END (A) to the RIGHT MOLDING (O) and BOTTOM (D) to the RIGHT BASE (K). Tighten four HIDDEN CAMS. Page 16 www.sauder.
S p te 13 31G L 31G D M K 4G 1S BLACK 9/16" LARGE HEAD SCREW (18 used for the BRACKETS) Fasten two CORNER BRACKETS (31G) to the BASES (K and L) and BOTTOM (D). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten three METAL BRACKETS (4G) to the BOTTOM (D). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the BRACKETS are even with the edge of the BOTTOM. Fasten the BASE (M) to the BOTTOM (D) and BASES (K and L).
S Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. p te 14 The perforations should be here. 1S BLACK 9/16" LARGE HEAD SCREW (24 used in this step) D U su nfi rf n ac is e he G d F U su nfi rf n ac is e he G d E E 23E The perforations should be here. 1N NAIL (16 used in this step) Carefully turn your unit over onto its front edges. Lay the LARGE BACKS (G) over your unit. Fasten the LARGE BACKS (G) to the BACKS (E and F).
S p te 15 1S BLACK 9/16" LARGE HEAD SCREW (16 used in this step) 27H I H H I 27H Fasten two HINGES (27H) to each DOOR (H and I). Use sixteen BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: The HINGES should be positioned exactly as shown. 414721 www.sauder.
S p te 16 33M 11S 39M 69K 95S BLACK 1/2" FLAT HEAD SCREW (4 used for the STRIKE PLATES) SILVER 1-1/2"" MACHINE SCREW (2 used for the BACKPLATE and KNOB) 6I 34M Q 39M 33M H R I 15S Q SILVER 5/8" MACHINE SCREW (4 used for the DECORATIVE ENDS) 1S BLACK 9/16" LARGE HEAD SCREW (16 used for the HINGES) IMPORTANT: You may need someone's help in this step. Carefully stand your unit upright. Fasten the DOORS (H and I) to the MOLDINGS (Q and R). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S).
S p te 17 A J S B J S ac e 1R J is in (8 used) F 2R he d su rf A Notched edge S Slide the SHELF MOLDING (S) onto the notched edge of an ADJUSTABLE SHELF (J). Repeat this step for the other SHELF MOLDING and ADJUSTABLE SHELF. Push the RUBBER SLEEVES (2R) over the remaining METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A) and UPRIGHT (B). Set the ADJUSTABLE SHELVES (J) onto the METAL PINS. *U.S. Patent No. 5,499,886 414721 www.sauder.
S p te WARNING 18 Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur. The TV and furniture will be unstable and may tip. BLACK 1-7/8” FLAT HEAD SCREW (1 used into a stud in your wall) 2S - The TV must weigh less than 135 lbs. - The base of the TV must be able to sit completely on this shelf. 1G BLACK 9/16” LARGE HEAD SCREW (1 used into the top of your unit) 1S 3M 4L C 135 lbs. 25 lbs. 25 lbs. 60 lbs.
414721 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 5 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. • Vérifier la taille et le poids du téléviseur.
ÉTAPE 10 ÉTAPE 16 Fixer le DESSOUS (D) sur le SOCLE GAUCHE (L). Serrer deux EXCENTRIQUES ESCAMOTABLES. Fixer le DESSOUS (D) au MONTANT (B) et à l’ARRIÈRE CENTAL (F). Utiliser trois VIS TÊTE PLATE 48 mm NOIRES (2S). Fixer l'EXTRÉMITÉ DROITE (A) à la MOULURE DROITE (O) et le DESSOUS (D) au SOCLE DROIT (K). Serrer quatre EXCENTRIQUES ESCAMOTABLES. IMPORTANT : L'assistance d'autrui peut être nécessaire à cette étape. Relever, avec précaution, l'élément dans sa position verticale.
Credencia de almacenamiento 414721 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 5 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. • Verifique el tamaño y peso del televisor.
PASO 10 PASO 16 Fije el FONDO (D) a la BASE IZQUIERDA (L). Apriete dos EXCÉNTRICOS ESCONDIDOS. Fije el FONDO (D) al PARAL (B) y al DORSO CENTRAL (F). Utilice tres TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (2S). IMPORTANTE: Usted puede necesitar la ayuda de alguien para este paso. Cuidadosamente ponga la unidad en posición vertical. Fije las PUERTAS (H e I) a las MOLDURAS (Q y R). Utilice ocho TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Fije los EXTREMOS DECORATIVOS (33M) a la PUERTA (H).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear valued customer: Thank you for your purchase from the Sauder family companies. It’s our pleasure to provide you with an affordable solution that meets your furniture and storage needs. I hope you will enjoy it for years to come. I am pleased with this company’s consistent ability to amaze the customer over time. My grandfather, Erie Sauder, founded the company in 1934 and later invented and patented the first commercially successful ready-to-assemble table.
