sauder.com Gets on your couch’s good side. Sofa Table Carson Forge Collection | Model 414443 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 361493 04/03/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification D A I G F K H C N B M J E D83 D75 D721 L N D84 O D83 D75 D721 P D84 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push thirty-two HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), SHELF (E), BACK (G), BRACE (H), and SIDE SKIRTS (N). Then, insert the metal end of eighteen CAM DOWELS (2F) into the HIDDEN CAMS in the ENDS, UPRIGHT, SHELF, BACK, and BRACE. Do not tighten the HIDDEN CAMS in this step.
Step 2 å å Turn fourteen CAM SCREWS (8F) into the LEGS (I, J, K, and L). Remember: Righty tighty. Lefty loosey. NOTE: Be sure to use the exact holes shown. (14 used) 8F 8F L K I J 8F Page 6 414443 www.sauder.
Step 3 å Fasten a CORNER ACCENT (8E) to each FRONT LEG (K and L). Use two SILVER 5/8" MACHINE SCREWS (15S). 15S SILVER 5/8" MACHINE SCREW (2 used in this step) 8E L 8E K Angled edge Angled edge www.sauder.
Step 4 å First, fill the hole in the side of each LEG (I, J, K, and L) 1/4 to 1/2 full with GLUE (54M). Then, insert four WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å å Now, fill the holes in the SIDE SKIRTS (N) 1/4 to 1/2 full with GLUE (54M). å NOTE: Be sure the WOOD DOWELS (15F) in the LEGS (I, J, K, and L) insert into the holes in the SIDE SKIRTS (N). Wipe away the excess GLUE. Fasten the LEGS (I, J, K, and L) to the ENDS (A and B) and SIDE SKIRTS (N). Tighten twelve HIDDEN CAMS.
Step 5 å Fasten the CABINET RAILS (Q and R) to the ENDS (A and B) and both surfaces of the UPRIGHT (C). Use eight GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å NOTE: The CABINET RAILS are marked "CABINET RIGHT" and "CABINET LEFT" for easy identification. 3S Roller end GOLD 5/16" FLAT HEAD SCREW (8 used in this step) 1 2 Q Finished edge 3 S HI urfa DD ce EN wi CA th M S Roller end Roller end 1 1 C 2 R Q 2 3 3 A K Roller end 3 2 1 R B L www.sauder.
Step 6 å Wrap the METAL FRAME (25M) around the MODESTY PANEL (F). Then, fasten the METAL FRAME to the MODESTY PANEL. Use eight BROWN 9/16" LARGE HEAD SCREWS (40S). å Cross the METAL BARS (26M) and line up the center holes in the BARS. Then, fasten the METAL BARS to the MODESTY PANEL (F). Use five BROWN 9/16" LARGE HEAD SCREWS (40S). 40S 26M BROWN 9/16" LARGE HEAD SCREW (13 used in this step) 26M F ce rfa Su th wi s le ho 25M 25M Page 10 414443 www.sauder.
Step 7 å Fasten the BACK SKIRT (M) to the SHELF (E). Tighten two HIDDEN CAMS. Rounded edge Sur HIDface w DEN ith CA MS E Long unfinished edge M Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 8 å First, fill the hole in the edge of the BACK SKIRT (M) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into the hole. Wipe away the excess GLUE. å Now, fill the large hole in the RIGHT REAR LEG (I) 1/4 to 1/2 full with GLUE (54M). å Fasten the SHELF (E) to the SIDE SKIRT (N). Tighten two HIDDEN CAMS. å NOTE: Be sure the WOOD DOWEL (15F) in the BACK SKIRT (M) inserts into the hole in the RIGHT REAR LEG (I). Wipe away the excess GLUE.
Step 9 å Fasten the BACK (G) to the RIGHT REAR LEG (I). Tighten one HIDDEN CAM. å Fasten the BRACE (H) to the RIGHT END (A). Tighten two HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Edge and surface with HIDDEN CAMS Sur withface HID CA DEN MS G H I www.sauder.
Step 10 å First, fill the hole in the edge of the LEFT REAR LEG (J) 1/4 to 1/2 full with GLUE (54M). Then, insert a WOOD DOWEL (15F) into the hole. Wipe away the excess GLUE. ! Caution Inspect the parts thoroughly before assembling. Disassembly of glued parts is extremely difficult. å Now, fill the hole in the BACK SKIRT (M) 1/4 to 1/2 full with GLUE (54M). å Fasten the LEFT END (B), LEFT REAR LEG (J), and SIDE SKIRT (N) to the SHELF (E), BACK (G), and BRACE (H). Tighten five HIDDEN CAMS.
Step 11 å å Carefully lay your unit on its front edges. Fasten the MODESTY PANEL (F) to the BACK (G) and BACK SKIRT (M). Use four BROWN 9/16" LARGE HEAD SCREWS (40S) through the METAL BARS (26M) and into the holes in the BACK and BACK SKIRT. 40S BROWN 9/16" LARGE HEAD SCREW (4 used in this step) F 26M S M urfa ET ce AL w BA itho RS ut G M 26M www.sauder.
Step 12 å Push a FOOT (10E) over the bottom edge of each LEG (I, J, K, and L). å With a hammer, gently tap a TACK GLIDE (12E) through the holes of the FEET (10E). 10E J L I K 10E Page 16 12E 414443 www.sauder.
Step 13 å å Carefully stand your unit upright. Pro Tip: Lift with your legs. And, you know, your arms. Fasten the UPRIGHT (C) to the BRACE (H). Use a BLACK 1-7/8" FLAT HEAD SCREW (2S). Finished edge Surface with HIDDEN CAMS C H 2S BLACK 1-7/8" FLAT HEAD SCREW (1 used in this step) www.sauder.
Step 14 å First, fill the four holes in the TOP (D) 1/4 to 1/2 full with GLUE (54M). Then, insert the WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å å Now, fill the four holes in the LEGS (I, J, K, and L) 1/4 to 1/2 full with GLUE (54M). å NOTE: Be sure the WOOD DOWELS (15F) in the TOP (D) insert into the holes in the LEGS (I, J, K, and L). Wipe away the excess GLUE. Fasten the TOP (D) to the ENDS (A and B), UPRIGHT (C), and BACK (G). Tighten eight HIDDEN CAMS.
Step 15 VIEW THE T-LOCK BOX VIDEO 1 2 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D721 D83 D83 O O D84 D84 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å Insert the DRAWER SIDES (D83 and D84) at an angle into the slot at each end of the RIGHT DRAWER FRONT (O).
Step 16 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D83 and D84). å NOTE: The DRAWER SLIDES are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Fasten a PULL (53K) to the RIGHT DRAWER FRONT (O). Use two SILVER 5/8" MACHINE SCREWS (15S). å Repeat this step for the other drawer. Fasten the DRAWER SLIDES (S and T) to the DRAWER SIDES (D83 and D84).
Step 17 å To insert the drawers into your unit, tip the fronts of the drawers down and drop the rollers on the drawers behind the rollers on the unit. Lift the fronts of the drawers up and slide them into the unit. å Push a CAM COVER (12P) onto each visible HIDDEN CAM in the SIDE SKIRTS (N). 50 lbs. 10 lbs. P N 10 lbs. O 25 lbs. 12P (2 used) N To cover HIDDEN CAMS www.sauder.
Step 18 å To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
Modèle 414443 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les CAMES ESCAMOTABLES dans cette étape. Enrober le CADRE EN MÉTAL (25M) autour du VOILE DE FOND (F). Fixer ensuite le CADRE EN MÉTAL sur le VOILE DE FOND. Utiliser huit VIS TÊTE LARGE 14 mm MARRON (40S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol.
ÉTAPE 11 ÉTAPE 16 Placer, avec précaution, l'élément sur ses chants avant. Insérer une EXCENTRIQUE DE COULISSE (10A) dans les CÔTÉS DE TIROIR (D83 et D84). Fixer le VOILE DE FOND (F) sur l’ARRIÈRE (G) et la PLINTHE ARRIÈRE (M). Utiliser quatre VIS TÊTE LARGE 14 mm MARRON (40S) à travers les BARRES EN MÉTAL (26M) et dans les trous dans l'ARRIÈRE et la PLINTHE ARRIÈRE. ÉTAPE 12 Mettre un PIED (10E) sur le chant inférieur de chaque PIED (I, J, K et L).
Modelo 414443 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Envolverse el MARCO METÁLICO (25M) alrededor el VELO DE FONDO (F). A continuación, fije el MARCO METÁLICO al VELO DE FONDO. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje treinta y dos EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), el PARAL (C), el ESTANTE (E), el DORSO (G), la RIOSTRA (H) y los FALDONES LATERALES (N).
PASO 11 PASO 16 Cuidadosamente coloque la unidad para que repose sobre los bordes delanteros. Inserte un EXCÉNTRICO DE CORREDERA (10A) dentro de los LADOS DE CAJÓN (D83 y D84). Fije el VELO DE FONDO (F) al DORSO (G) y al FALDÓN POSTERIOR (M). Utilice cuatro TORNILLOS MARRONES DE CABEZA GRANDE de 14 mm (40S) a través las BARRAS METÁLICAS (26M) y dentro de los agujeros en el DORSO y en el FALDÓN POSTERIOR. Fije las CORREDERAS DE CAJÓN (S y T) a los LADOS DE CAJÓN (D83 y D84).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
