sauder.com WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Bookcase/Footboard Pogo Collection | Model 414436 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-14 Hammer Français 15-17 Español 18-20 Safety 21-22 Warranty Page 2 Not actual size Skip the power trip. This time. 23 414436 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A2 RIGHT END (1) E TOP (1) I BACK (1) B2 LEFT END (1) F BOTTOM (1) J SKIRT (1) C UPRIGHT (1) G2 FRONT PANEL (1) K RAIL (1) D LOWER UPRIGHT (1) H L TOP MOLDING (1) SHELF (1) E L A2 I C H K D G2 B2 F www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F 12E TACK GLIDE - 4 15F WOOD DOWEL - 4 4G METAL BRACKET - 8 40M CARD SHEET - 1 2S 1N 8M 6S BLACK 1-7/8" FLAT HEAD SCREW - 2 CAM DOWEL - 13 21M GLUE - 1 1R NAIL - 49 14S BROWN 1-1/2" FLAT HEAD SCREW - 4 Page 4 2F HIDDEN CAM - 13 CARD HOLDER - 2 METAL PIN - 4 BROWN 7/16" LARGE HEAD SCREW - 16 97S SILVER 3/8" MACHINE SCREW - 4 414436 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Push thirteen HIDDEN CAMS (1F) into the ENDS (A2 and B2), LOWER UPRIGHT (D), BOTTOM (F), and SHELF (H). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1529 to watch a video on how to assemble your unit.
Step 2 å Fasten the SHELF (H) to the RIGHT END (A2). Tighten two HIDDEN CAMS. å Fasten the LOWER UPRIGHT (D) to the SHELF (H). Tighten a HIDDEN CAM. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Curved edge Finished edge A2 Sur f a c HID e w DEN ith CA MS H ith e w AMS c a f Sur DEN C D HI Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 3 å å å Fasten four METAL BRACKETS (4G) to the RAIL (K). Use four BROWN 7/16" LARGE HEAD SCREWS (6S). Remember: Righty tighty. Lefty loosey. NOTE: Be sure the BRACKETS are even with the edges of the RAIL. Fasten the CARD HOLDERS (21M) to the other surface of the RAIL (K). Use four SILVER 3/8" MACHINE SCREWS (97S). 6S 4G BROWN 7/16" LARGE HEAD SCREW (4 used for the METAL BRACKETS) Surface with more holes 4G K 4G Open slot 21M 97S SILVER 3/8” MACHINE SCREW (4 used for the CARD HOLDERS) www.
Step 4 å Fasten the RAIL (K) to the RIGHT END (A2) and SHELF (H). Use three BROWN 7/16" LARGE HEAD SCREWS (6S). å Fasten the BOTTOM (F) to the RIGHT END (A2) and LOWER UPRIGHT (D). Tighten two HIDDEN CAMS and use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Maximum 210 degrees Arrow Minimum 190 degrees 6S BROWN 7/16" LARGE HEAD SCREW (3 used for the RAIL) Open slot These holes must be here.
Step 5 å First, fill the holes in the FRONT PANEL (G2) 1/4 to 1/2 full with GLUE (8M). Then, insert the WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å Now, fill the holes in the RIGHT END (A2) 1/4 to 1/2 full with GLUE. Then, insert the WOOD DOWELS in the FRONT PANEL (G2) into these holes. Wipe away the excess GLUE. Fill the holes 1/4 to 1/2 full with GLUE. ! Caution Inspect the parts thoroughly before assembling. Disassembly of glued parts is extremely difficult.
Step 6 å First, fill the holes in the LEFT END (B2) 1/4 to 1/2 full with GLUE (8M). Then, insert the WOOD DOWELS (15F) in the FRONT PANEL (G2) into the holes in the LEFT END. Wipe away the excess GLUE. å Fasten the LEFT END (B2) to the BOTTOM (F) and SHELF (H). Tighten four HIDDEN CAMS. å Fasten the RAIL (K) to the LEFT END (B2). Use a BROWN 7/16" LARGE HEAD SCREWS (6S). å å Insert four METAL PINS (1R) into the UPRIGHT (C). Fill the holes 1/4 to 1/2 full with GLUE.
Step 7 å Fasten the TOP (E) to the ENDS (A2 and B2). Tighten four HIDDEN CAMS. å NOTE: Be sure the METAL PINS in the UPRIGHT (C) insert into the holes in the TOP (E). å Fasten the TOP MOLDING (L) to the TOP (E). Use four BROWN 1-1/2" FLAT HEAD SCREWS (14S). å NOTE: Do not overtighten the SCREWS into the TOP. Maximum 210 degrees Arrow Minimum 190 degrees 14S BROWN 1-1/2" FLAT HEAD SCREW (4 used in this step) Rounded edge e fac Sur Curved edge es hol h t wi A2 E L C B2 www.sauder.
Step 8 å Fasten the SKIRT (J) to the ENDS (A2 and B2) and BOTTOM (F). Use four METAL BRACKETS (4G) and eight BROWN 7/16" LARGE HEAD SCREWS (6S). Almost time to celebrate! With a nap. 6S BROWN 7/16" LARGE HEAD SCREW (8 used in this step) Curved edge J A2 F 4G B2 4G 4G Page 12 414436 www.sauder.
Step 9 å Carefully turn your unit over onto its front edges. Unfold the BACK (I) and lay it over your unit. å Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (I) to your unit using the NAILS (1N). å With your hammer, gently tap four TACK GLIDES (12E) into the bottom edges of the ENDS (A2 and B2). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 10 å å å å Carefully stand your unit upright. Separate the CARDS on the CARD SHEET (40M) and insert one into each CARD HOLDER. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? 40M 30 lbs. 30 lbs. total 50 lbs. total Page 14 414436 www.sauder.
Modèle 414436 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 4 Ne pas serrer les CAMES ESCAMOTABLES dans cette étape. Fixer la TRAVERSE (K) à l'EXTRÉMITÉ DROITE (A2) et à la TABLETTE (H). Utiliser trois VIS TÊTE LARGE 11 mm MARRON (6S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer treize EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A2 et B2), le MONTANT INFÉRIEUR (D), le DESSOUS (F) et la TABLETTE (H).
ÉTAPE 7 ÉTAPE 9 Fixer le DESSUS (E) aux EXTRÉMITÉS (A2 et B2). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. REMARQUE : S'assurer de bien insérer les GOUPILLES EN MÉTAL situées sur le MONTANT (C) dans les trous du DESSUS (E). Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (I) et le placer sur l'élément. Fixer la MOULURE DE DESSUS (L) au DESSUS (E).
Modelo 414436 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 4 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el RIEL (K) al EXTREMO DERECHO (A2) y al ESTANTE (H). Utilice tres TORNILLOS MARRONES DE CABEZA GRANDE de 11 mm (6S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje trece EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A2 y B2), del PARAL INFERIOR (D), del FONDO (F) y del ESTANTE (H).
PASO 7 PASO 9 Fije el PANEL SUPERIOR (E) a los EXTREMOS (A2 y B2). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. NOTA: Asegúrese que las ESPIGAS DE METAL sujetadas al PARAL se inserten dentro de los agujeros del PANEL SUPERIOR (E). Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (I) y colóquelo sobre la unidad.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
